• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.89-92
• /
• 2008

This research analyzed the basic characteristics of unhardened concrete and the compression strength characteristics of hardened concrete according to liquidity retention agent mix rate change to improve the liquidity fluidity retention performance of high performance concrete, and produced the following results. The moment fluidity retention agent is added according to fluidity retention agent mix rate change, which increased fluidity retention agent mix rate, slump flow decreased, and in the case of slump flow according to the progress time change by the fluidity retention agent mix rates, the more fluidity retention agent mix rate increased, the lower slump flow change rate became. The moment fluidity retention agent is added according to fluidity retention agent mix rate change, fluidity retention agent mix rate increased compared to non-mixture of fluidity retention agent, and the air amount by progress time change by the fluidity retention agent mix rates slightly increased, however target range is still met and unit volume mass is inversely proportional to air amount. Compression strength according to age progress by the fluidity retention agent mix rates was shown to increase slightly with increase in fluidity retention agent mix rate, and yet the difference was not significant.

• 한국주조공학회지
• /
• 제26권6호
• /
• pp.241-248
• /
• 2006

The effects of silicon content and melt treatment on the fluidity of Al-Si alloys during squeeze casting were investigated. The fluidity of Al-3.0 wt%Si alloy was found to be lower than that of Al-1.0 wt%Si and the fluidity of the alloy with more than 3.0 wt%Si increased with the silicon content upto 13.0 wt% and rather decreased with15.0 wt%. The fluidity was also increased by the separated treatment of grain refinement or eutectic modification, and even more by the simultaneous treatment of both. The fluidity of hypereutectic alloy was increased by the refinement of primary silicon particle.

• 한국주조공학회지
• /
• 제22권3호
• /
• pp.109-113
• /
• 2002

A good fluidity of high strength Al-alloys is required to cast thin wall castings needed to reduce the weight of cast parts. The fluidity, measured as the length to which the metal flows in a standard channel, is affected by many factors, such as the pouring temperature, solidification type of the alloy, the channel thickness, melt head, mold materials and temperature, coating etc. Therefore the experimentally measured fluidity scatters very much and makes it difficult to estimate the fluidity of a melt with a few measurements. The effect of Ti content and grain refinement on the fluidity of high strength aluminum alloy was investigated with a test casting with 8 thin flow channels to reduce the scattering of the fluidity results. The fluidity of Al-4.8%Cu-0.6%Mn Al-6.2%Zn-1.6%Mg-1.0%Cu and well-known commercial aluminum alloy, A356 was tested. Initial content of Ti was varied from 0 to 0.2wt% and Al-5Ti-B master alloy was added for grain refinement. The flow length varied linearly with superheat. By adding Ti and Al-5Ti-B, the fluidity increased. The grain size decreased by adding grain refiner at the same time. The fluidity depended on the degree of grain refinement. The fluidity of the alloy solidifying in mushy type is improved by grain refinement, because grain refinement increases the solid fraction at the time of flow stoppage.

• 한국세라믹학회지
• /
• 제50권2호
• /
• pp.149-156
• /
• 2013

This study examines the effects of limestone's factors on the fluidity of cement paste when of up to 15%. As the substitution ratio of limestone powder increases, the fluidity of the paste is also improved; however, it has no correlation to the $CaCO_3$ content of the limestone, fineness of the limestone, and fluidity of the pastes. Regardless of clay content of the limestone, it showed a similar mini-slump, so there was no correlation between the clay content and the fluidity of the paste. Also, the total organic carbon content of the limestone and the fluidity of the paste showed no correlation. Regardless of the limestone's grade or fineness, n value of powder gained by using the Rosin-Rammler distribution function showed that the fluidity of the paste increased as the n value reduced. It was also shown that particle size distribution of ordinary Portland cement with limestone powder had a major effect on the fluidity of the paste.

• 한국주조공학회지
• /
• 제32권3호
• /
• pp.127-132
• /
• 2012

Al-Zn-Mg alloys, being high strength aluminum alloys, have attracted attention as a material of automobile parts that require higher mechanical properties and lightness. Automobile parts with complex shapes are manufactured by low-priced casting method, but Al-Zn-Mg alloys are difficult to cast because of its poor hot cracking, feeding, and fluidity. Thus fluidity experiments on Al-Zn-Mg alloys were conducted for the castability evaluation. The effects of Mg and Zn, representative elements of Al-Zn-Mg alloys, on fluidity were observed. Spiral mold was used for fluidity experiments and the lengths of solidified specimens were measured after melting and gravity casting. Correlation between microstructures and fluidity length based on the alloy composition was considered. According to the experimental results, as the amount of Mg and Zn increased, fluidity decreased. Also, it was confirmed that fluidity change by the variation of Mg composition was greater than that of Zn.

• 한국주조공학회지
• /
• 제10권1호
• /
• pp.31-42
• /
• 1990

The full mould casting process in one of the newly developed techniques which has many advantages. Unbonded sand mould has been prepared for the major mould and $CO^2$ gas mould has been used occasionally for comparison. Patterns were built up with expanded polystyrene and coated with three different materials. Silica, graphite and zircon were used for the coating layer. The effects on fluidity and temperature loss of molten metals were investigated. The molten metals were Al-5% Si alloy, Cu-30% Zn alloy and gray iron of approximately 4.0% of carbon equivalent. Experimental variables were runner section area, superheat, sprue height, coating materials, coating thickness and apparent density of EPS pattern. The effects of coating materials on fluidity and temperature loss of the molten metals during transient pouring are summarized as follows : As runner section area, superheat and sprue height increased, fluidity increased. Temperature loss decreased as runner section area and sprue height increased. However, reversed effects were observed in the case of superheat increment. The coating materials decreased the fluidity of each alloy in the order of silica, graphite and zircon. Zircon brought to the highest temperature loss among the coating materials used. The fluidity increased in the order gray iron, Cu-30% Zn and Al-5% Si alloy while temperature loss in the reverse order. Especially in case of reduced pressure process, the fluidity was increased apparently. Al-5% Si alloy showed the lowest temperature loss among the alloys. The increment of the apparent density of EPS pattern resulted in the fluidity decrease and temperature loss increase. The relation between fluidity and temperature loss of each alloy can be expressed by the following equation within the coating thickness limit of 0.5-1.5㎜. F^*={\frac{a}{T^*-b}}-c$ where, $F^*$ : fluidity in the Full mould, $T^*$ : temperature loss in the mould. a : parameter for full mould. b, c : constants.

• 한국건축시공학회지
• /
• 제4권2호
• /
• pp.129-136
• /
• 2004

High fluidity concrete(HFC) requires high dosage of superplasticizer to acquire sufficient fluidity, and high contents of fine powder and viscosity enhancing admixtures to resist segregation. The use of high amount of admixtures to make HFC at batcher plant in ready mixed concrete company is one of the reasons to raise the manufacturing cost of HFC. For this reason, new type of manufacturing method of HFC are described using both flowing concrete method and segregation reducing superplasticizer(SRS) in order to gain economical profit and offer the convenience for quality control.. As dosage of melamine based superplasticizer increases, it shows that fluidity and bleeding increase, while air contents and ratio of segregation resistance decrease. It also shows that addition of viscosity agent into superplasticizer reduce bleeding and improve segregation resistance of concrete. Dosage of AE agent into superplasticizer containing viscosity agent recovers loss of air contents during flowing procedure. Combination of proper contents of superplasticizer, viscosity agent and AE agent make possible to develope segregation reducing type superplasticizer. Compressive strength of high fluidity concrete applying flowing method with it is higher than that of base concrete. No differences of compressive strength between compacting methods are found. For the estimation of construction cost of high fluidity concreting using segregation reducing type superplasicizer, under same strength levels, although material cost of high fluidity concrete is somewhat higher than that of plain concrete due to segregation reducing type superplasticizer cost, labor cost and equipment cost of high fluidity concrete is cheaper than that of plain concrete. However, based on the strength differences, high fluidity concrete shows lower material cost, labor cost and equipment cost than that of plain concrete due to decreasing in size of member and re-bar caused by high strength development of concrete.

• 한국건설순환자원학회논문집
• /
• 제1권1호
• /
• pp.67-75
• /
• 2013

최근 노출 콘크리트에 대한 관심이 높아지고 있으며, 이에 따라 노출 콘크리트의 사용이 확대되고 있다. 그러나 콘크리트 구조물은 점차 복합한 단면 및 조밀한 철근으로 인하여 기존의 노출 콘크리트용 일반 콘크리트를 적용하기 어려운 실정이다. 따라서, 본 논문에서는 노출 콘크리트에 고유동 콘크리트를 적용하기 위하여 플라이애시 및 석회석 미분말을 사용한 고유동 노출 콘크리트를 제조하였으며, 콘크리트의 품질특성(유동특성, 역학특성 및 표면특성)을 평가하였다. 실험배합은 OPC 및 LSP10을 기준배합으로 하였으며, FA 혼합률(0, 10, 15 및 20)에 따라 콘크리트 품질에 미치는 영향을 평가하였다. 실험결과, 고유동 노출 콘크리트의 유동특성, 역학특성 및 표면특성은 소요 요구 조건을 만족하는 것으로 나타났으며, 플라이애시 및 석회석 미분말의 혼합에 따라 유동성 및 표면마감성이 향상되는 것으로 나타났다. 이를 통하여, 노출 콘크리트용 고유동 콘크리트 개발을 위한 기초연구 자료로써 활용하고자 한다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표회 논문집(I)
• /
• pp.93-98
• /
• 1998

Fluidity retention of concrete used high range water reducing AE agent(HWAE) is varied according to type, dosage amount and dosing method of HWAE. The type and substitution ratio of mineral admixture also have influence on the fluidity retention of concrete using HWAE. For the purpose of improving the fluidity retention in concrete used HWAE, 3 types of HWAE and ground granulated blast furnace slag(SG) are applied in cement-based composites such as cement paste, mortar and concrete respectively. According to using the HWAE of naphthalene sulfonates and SG, the fluidity retention of mortar and concerete is improving the fluidity retention and strength of concrete regardless of type of HWAE.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.195-196
• /
• 2018

The Research is underway to utilize heavyweight concrete for various applications. One of them is to use heavy concrete as a marine concrete such as a breakwater to resist wave. Marine concrete is often complex in shape and requires high fluidity. When the heavyweight concrete is high fluidity, there is a high risk of segregation due to the high density of the coarse aggregate. Therefore, we evaluate the fluidity of heavyweight concrete using heavy fine aggregate. As a result of the fluidity evaluation of the heavyweight concrete, the fluidity of the heavy fine aggregate was similar to that of ordinary concrete. Therefore, it is considered that the use of heavy fine aggregate in the development of high fluidity heavyweight concrete will be one of the methods.