• Tunnel and Underground Space
• /
• v.30 no.3
• /
• pp.242-255
• /
• 2020

The numerical simulations of Heater Experiment-D (HE-D) at the Mont Terri rock laboratory in Switzerland were performed to investigate an applicability of FLAC3D to reproduce the coupled thermo-hydro-mechanical (THM) behaviour in Opalinus Clay, as part of the DECOVLEX-2015 project Task B. To investigate the reliability of numerical simulations of the coupled behaviour using FLAC3D code, the simulation results were compared with the observations from the in-situ experiment, such as temperature at 16 sensors, pore pressure at 6 sensors, and strain at 22 measurement points. An anisotropic heat conduction model, fluid flow model, and transversely isotropic elastic model in FLAC3D successfully represented the coupled thermo-hydraulic behaviour in terms of evolution for temperature and pore pressure, however, performance of the models for mechanical behavior is not satisfactory compared with the measured strain.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.76-80
• /
• 2004

Nano-sized ZnO colloids were prepared by use of spray combustion method. for combustion reaction, $Zn(NO_3)_2{\cdot}6H_2O$ and $CH_6N_4O$ were employed as an oxidizer and a fuel. Exothermic peak was shown at $230^{\circ}C$ by DTA/TGA, and it was considered as a combustion reaction followed by ignition of the precursor mixture. In case of spray combustion method, because insufficient contents of molecules and radicals generated from precursor droplets may lead an incomplete igmition, the ignition temperature of combustion chamber was chosen at $500^{\circ}C$. For diminishing aerosol coagulation, the droplet number concentration was reduced by filter media. The fluid was laminar with 2.5 seconds of aerosol residence time. The synthesized colloids had spherical shape with 180 nanometer size, and the crystalline phase was ZnO with hexagonal structure.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.1-9
• /
• 2017

Numerical computations are performed to investigate the effect of pintle stroke on the performance of an internal pintle thruster. Results show that the thrust control ratio was less than 2% and the aerodynamic load ratio was 22% as the pintle stroke increased. The flow past the nozzle throat rapidly expanding because of the shape of the pintle, and a shock wave was generated. Particularly, at the pintle stroke distance of 4 and 5 mm, the shock wave hit the wall of the nozzle, results in peeling bubbles. Depending on the altitude, the thrust increased and the aerodynamic load decreased, but the difference was as small as 1.5%. In the presence of the bore, the reduction of the pintle tip area resulted in a decrease in aerodynamic load.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.3
• /
• pp.237-243
• /
• 2010

In this study, the effect of the shape of a pintle(obstacle) on thrust-modulation performance and drag in a pintle rocket was investigated by a cold flow test and by computational fluid dynamics. Pintle movement caused a monotonic increase in the chamber pressure. Thrust generated by the pressure distribution on the pintle body was linearly changed to the chamber pressure, and this thrust was greater than that generated by the nozzle-wall pressure distribution. Because the shock pattern in the nozzle changes with the shape of the pintle body and pressure ratio, the thrust generated by the nozzle-wall pressure is not directly affected by chamber pressure. The drag due to the pintle(obstacle) can be minimized for a fully linear pintle shape, regardless of chamber pressure.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.21-26
• /
• 2008

Recently, small and medium-sized buildings have employed a multi-heat pump. The major benefits of the multi-heat pump over a conventional system are that it is easier system to maintain along with a diversification of facility use, and high comfortability. The performance of multi-heat pump systems can be enhanced by using geothermal energy instead of air source energy. This paper describes the multi-heat pumps applied in an ground source heat pump system for an actual building. The performance of a ground source multi-heat pump installed in the field was investigated in cooling mode. The maximum COP of the systems with single U-tube and double tube ground loop heat exchangers were 6.6 and 6.0, respectively. It is suggested that the new algorithms to control the flow rate of secondary fluid for ground loop heat exchanger have to be developed in order to enhance the performance of the system.

• Journal of the Korean Institute of Gas
• /
• v.3 no.1
• /
• pp.33-40
• /
• 1999

The extraction characteristics of lipids from powdered sea mustard have been investigated by the use of supercritical carbon dioxide($SC-CO_2$) and cosolvents. The extraction rate was increased as the particle size of the sea mustard is smaller, the pressure is higher, the temperature is lower, and the quantities of the fluid is more. However, the extraction yield of lipids from sea mustard was almost constant at a given condition. The optimum extraction condition was determined with the extraction yield of $1.45wt\%$ at 300um of particle size, 313K of $SC-CO_2$ temperature, 13.8MPa of pressure, and 30L/min of flow rate. Ethanol was the most efficient cosolvent among ethanol, methanol, and hexane. The extraction yield was increased at about 2.21times by the addition of ethanol as a cosolvent to $SC-CO_2$. As the residence time and the average concentration of lipids were decreased, the mass transfer parameter($k_fa$) was increased. But the opposite result was obtained when the ethanol was used as cosolvent.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.4
• /
• pp.1-9
• /
• 2010

Fuel shutoff valve of a gas generator controls propellant mass flowrate of a rocket engine, by using pilot pressure and spring force. The developing fuel shutoff valve can be self sustained even though pilot pressure is removed in an actuator. Therefore, it is necessary to analyze the characteristics of the forces with respect to the opening and closing of the valve in order to evaluate its performance. In light of this, the valve has been designed to adjust the control pressure for the opening of the poppet and to determine the working fluid pressure at which the valve starts to close. This paper also has been designed dynamic model using the AMESim and predicted flow coefficient of the valve by Fluent CFD analysis. Various results from the prediction and the analysis have been compared with experiments. Finally, dynamic characteristics of the valve have been verified with experimental results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.5
• /
• pp.10-17
• /
• 2021

In this study, cold-flow test of simulant gel is conducted using a pressure swirl injector to identify spray characteristics according to gellant weight percent. Experiment results show the aircore is developed locally at the nozzle and expanded to the entire swirl chamber as the supply pressure increases. The aircore formation of simulant gel showed no significant difference compared to Newtonian fluid. The spray pattern was classified into four distinct shapes where relationship between the breakup regimes and dimensionless numbers were investigated. In the future, additional study is necessary to understand the aircore formation mechanism, stability and spray characteristics at different configuration of the swirl chamber shape.

• Journal of Korea Water Resources Association
• /
• v.56 no.2
• /
• pp.125-137
• /
• 2023

In marine environments, plastics have become more abundant due to increasing plastic use. Especially, in coastal regions, particles may remain for a long time, and they interact with flows, wind, sand and human activities. This study aimed thus to observe how plastic debris interacts with and escape from sediments. A series of experiments were conducted in order to gain a better understanding of particle release from coastal sediments into water body. An oscillating water tunnel was built for the experiments, and used to generate oscillatory flows of relatively high Reynolds number and induce sediment transport. Spherical plastic particles of three different sizes was used in lieu of plastic debris in environments. It was observed that release of the particles was directly related to change of bedform, which is in turn determined by the flow condition. Also smaller particles tend to escape the sediment more readily. Critical values for dimensionless parameters are proposed.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.11
• /
• pp.63-70
• /
• 2023

Underground carbon dioxide (CO₂) storage emerges as a pivotal strategy for mitigating atmospheric CO₂ emissions and addressing global warming concerns. This study investigates techniques to optimize storage efficiency in aquifers, which stand out for their superior capacity compared to other geological layers. The focus is on the application of nonionic and anionic surfactants to enhance CO₂ storage efficiency within confined spaces. A specialized micromodel facilitating fluid flow observation was employed for the evaluation. Experimental results revealed a noteworthy minimum 40% increase in storage efficiency at the lowest injection rate when utilizing nonionic and anionic surfactants, in comparison to pure water injection. Interestingly, no significant variations in storage efficiency were observed based on the ionicity and concentration of the surfactants under investigation. These findings have implications for guiding the selection and concentration determination of surfactants in future underground CO₂ storage endeavors.