• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.1
• /
• pp.10-14
• /
• 2008

We synthesized GaN nanowires with high quality using the vapor phase epitaxy technique. The GaN nanowires were obtained at a temperature of $950^{\circ}C$. The Ar and $NH_3$ flow rates were 1000 sccm and 50 sccm, respectively. The shape of the GaN nanowires was confirmed through FESEM analysis. We were able to conclude that the GaN nanowires synthesized via vapor-solid (VLS) mechanism when the source was closed to the substrate. On the other side, the VS mechanism changed to vapor-liquid-solid (VLS) as the source and the substrate became more distant. Therefore, we can suggest that the large amount of Ga source from initial growth interrupt the role of catalyst on the substrate.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.141-149
• /
• 2013

IETF 6LoWPAN standard technique has been studied in IoT environment to support the IPv6 packet communication. 6LoWPAN protocol for transmission of packets mainly in the AODV routing protocol and a variety of extended techniques have been investigated. In particular, consisting of nodes with limited resources in a network error occurs when the 6LoWPAN reliable data transfer and fast routing method is needed. To this end, in this paper, we propose resilient routing protocol and extension of IETF LOAD algorithm, for optimal recovery path, More specifically, the optimal recovery path setup algorithm, signal flow, and detailed protocols for the verification of the reliability of packet transmission mathematical model is presented. The proposed protocol techniques to analyze the performance of the NS-3 performance through the simulation results that is end-to-end delay, throughput, packet delivery fraction and control packet overhead demonstrated excellence in comparison with existing LOAD.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.108-116
• /
• 2013

The input buffer in Network on Chip (NoC) router plays a key role in on-chip-network performance, which is utilized in flow control and virtual channel. However, increase in area and power due to input buffers as the network size gets larger is becoming severe. To solve this problem, a bufferless deflection routing without input buffer was suggested. Since the bufferless deflection routing shows poor performance at high network load, other approaches which combine the deflection routing with small size side buffers were also proposed. Nonetheless these new methods still show deficiencies caused by frequent path collisions. In this paper, we propose a modified deflection routing technique using a location based priority. In comparison with existing deflection routers, experimental results show improvement by 12% in throughput with only 3% increase in area.

• Journal of Korea Water Resources Association
• /
• v.47 no.5
• /
• pp.491-500
• /
• 2014

To estimate the severity of streamflow drought, this study introduced the concept of streamflow drought index based on threshold level method and Seomjingang Dam inflow was applied. Threshold levels used in this study are fixed, monthly and daily threshold, The $1^{st}{\sim}3^{rd}$ analysis results of annual drought, the severe hydrological droughts were occurred in 1984, 1988 and 1995 and the drought lasted for a long time. Annual compared to extreme values of total water deficit and duration, the drought occurred in 1984, 1988, 1995 and 2001 was serious level. In the results of study, because a fixed threshold level is not reflect seasonal variability, at least the threshold under seasonal level was required. Threshold levels determined by the monthly and daily were appropriate. The proposed methodology in this study can be used to forecast low-flow and determine reservoirs capacity.

• Composites Research
• /
• v.28 no.6
• /
• pp.340-347
• /
• 2015

As resin impregnates through the fiber preform in vacuum assisted resin transfer molding process, the volume of fibers is changed by expansion of fiber mat according to filling time. It causes not only the change in dimension but also the decrease of mechanical properties of the composite product. Moreover, it results in the economic loss by increase of the used amount of resin especially in the large product such as wind turbine blade. In this study, the ways to control fiber volume fraction were investigated by both the experimental and theoretical analyses on the expansion of fiber preform as the preform was impregnated by resin in the VARTM process. Two kinds of swelling stage were observed as flow front progressed, which was analyzed by comparing the experimental and simulation results. The process parameters are expected to be optimized by investigating the swelling behavior of fiber preform in the manufacturing process of the composite product.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.2
• /
• pp.164-170
• /
• 2010

In brushless DC motor, current flow should be controlled such that only properly selected 2 out of 3 phases carry current depending on the position of rotor. In order to detect position of rotor, hole sensor, encoder, optical position-detecting sensor, and magnetic position-detecting sensor are frequently employed. These sensors not only often cause malfunction in low and high temperature but they also have disadvantage of increasing cost and size of an motor system. To reduce the cost and size and to increase the robustness of the motor system, recently researches on sensorless motor dirve are very active. This paper proposes a novel unipolar PWM switching method that can improve the control problem caused by the difficulty of detecting zero crossing point at high revolution speed by minimizing the switching noise while increasing the lifespan of the drive system.

• Journal of Environmental Science International
• /
• v.21 no.10
• /
• pp.1181-1186
• /
• 2012

We studied the ozone concentrations generated by low-temperature dielectric barrier discharge plasma reactor after adding air and phytoplankton to control the ozone concentrations in seawater. We also examined the numbers of bacteria and Vibrio spp. after treatment using the plasma reactor. As the airflow rate was increased, more ozone was removed. Although marked variation in the ozone decrease was observed with and without airflow, the rate of ozone removal did not increase proportionately with the airflow rates. The ozone concentration decreased with increasing organic matter and time. The amount of organic matter seems to be an important factor decreasing the dissolved ozone concentration in liquid. The ozone concentration was 0.07, 0.32, 1.28, and 2.3 mg/L when operating the plasma reactor for 30, 60, 180, and 300 s, respectively; i.e., the ozone concentration increased with the reactor operating time. The initial numbers of bacteria and Vibrio spp. were 800 and 480 CFU/mL, respectively. After operating the plasma reactor at a flow rate of 6 L/min for 30 s, no bacteria or Vibrio spp. were detected. The disinfection effect of this plasma reactor seems to be superior to that of a conventional ozone generator.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.6
• /
• pp.41-48
• /
• 2014

In this study, the behavior of fill dam with continuous water level change considering velocity changes via centrifugal model test was investigated. In addition, the collapse of fill dam due to the overflow was also experimentally simulated. The experimental results demonstrate that the pore water pressures and displacements vary in proportion to the water-level-change velocity, and the displacement increment is independent to the water-level-change velocity. Also, it is confirmed that the continuous water level change induces to the progress of fill-dam deformation due to displacement accumulation and the fill-dam stability dramatically degrades owing to the overflow. Hence, the real-time monitoring of pore water pressures and displacements of fill dam, and the control of water level in heavy rain through the countermeasure such as opening sluice gates are needed to ensure the stability of fill dam.

• Journal of the Korean Geographical Society
• /
• v.33 no.3
• /
• pp.355-364
• /
• 1998

Flume experiments are conducted to describe the channel morphology at a tributary junction and to examine the influence of channel arrangements and hydrologic conditions on the channel morphology. When flow momenta of two tributaries are equal, a receiving stream tends to align with an axis bisecting junction angle. It causes lateral migration of a receiving stream according to an initial channel arrangement. As a result, the post-fonfluent channel morphology varies with plan geometry of a confluence such as symmetry, transition and asymmetry. Bed scour is the most notable morphology within a junction site. Its shape is characterized by steep walls which are primarily influenced by junction angle. Key control of scour dimension is also junction angle. Although the principle of accordant junction has been undoubtedly accepted, discordance is commonly developed at model and natural stream confluences. Unit discharge ratio of confluent streams is the most crucial factor because both discharge and sediment concentration ratios have an effect on discordance at a junction.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1532-1548
• /
• 2008

The tunnel type spillways is under construction to increasing water reservoir capacity in Dae-am dam. The tunnel outlet was planned to be made after installing slope stabilization system on natural slope there. Generally, the tunnel outlet is made perpendicularly to the slope, but in this case, it had to be made obliquely to the slope for not interrupting flow of river. Because of excavation in condition of natural slope caused to deflecting earth pressure, the outlet couldn't be made. So, artificial ground made with concrete that it was constructed in the outside of tunnel for producing the arching effect which enables to make a outlet. We were planned tunnel excavation was carried out after artificial ground made. Artificial ground made by poor mix concrete of which it was planned that the thickness was at least 3.0m height from outside of tunnel lining and 30cm of height per pouring. Spreading and compaction was planned utilized weight of 15 ton roller machine. In order to access of working truck, slope of artificial ground was designed 1:1.0 and applied 2% slope in upper pert of it for easily drainage of water. In addition to, upper pert of artificial ground was covered with soil, because of impaction of rock fall from upper slope was made minimum. The tunnel excavation of the artificial ground was designed application with special blasting method that it was Super Wedge and control blasting utilized with pre-percussion hole.