• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.5
• /
• pp.591-598
• /
• 2011

Tip position control of a flexible cantilever is difficult due to the non-minimum phase dynamics that result from the finite propagating speed of a mechanical wave along the cantilever. In this paper, we propose a method for the tip position control using a light and cheap accelerometer that does not bring any significant change to the dynamics of the cantilever system. The linear system identification model of the flexible cantilever is obtained with measurements by a laser displacement sensor. A Kalman estimator is designed with this model and calculates the estimated tip position with the acceleration data of the accelerometer that is attached on the tip of the cantilever. To verify reliability of the estimator, the estimated tip position is used to the feedback control system that uses a fuzzy logic controller. The control results are compared with those of the fuzzy control system where the real tip position is measured by a laser displacement sensor. Also, the performance of the estimator with the accelerometer is presented and discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.205-212
• /
• 1997

In this study, active vibration control for a flexible cantilever beam was performed by using the intelligent control technique. The intelligent control method which integrating the back propagation algorithm and the fuzzy inference technique was proposed and its performance was examined. The proposed control algorithm for the flexible cantilever beam was verified via computer simulation of active vibration control. Furthermore, the control system and its efficiency were investigated via experiments on active vibration control by the intelligent control technique without a digital signal processing device.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.3
• /
• pp.107-113
• /
• 1997

This paper presents the active control of a flexible cantilever beam vibration. The cantilever beam was excitied by a steady-state harmonic and white noise point force and the control was performed by one piezo ceramic actuator bonded to the surface of the beam. An adaptive controller based on filtered-x LMS algorithm was used and the controller was defined by minimizing the square of the response of error sensor. In the experiment, gap sensor was used as an error sensor while the sinusoidal or white noise was applied as a disturbance. In the case of sinusoidal input, more than 20 dB of vibration reduction was achieved over all range of the natural frequencies and it takes 5 seconds to control the vibration at first natural frequency and 1 second at other natural frequencies. In the case of white noise input, 7 dB of vibration reduction was achieved at the first natural frequency and good control performance was achieved in the considered whole frequency range. Results indicate that the vibration of a flexible cantilever beam could be controlled effectively when the piezo ceramic actuator was used with filtered-x LMS algorithm.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.4 s.97
• /
• pp.445-451
• /
• 2005

This paper is the result of a experimental study about non-linear one to one modal coupling of a flexible circular cantilever beam which was transversely excited with harmonic excitation. It was proved that 2 order jumping in out of plane was caused by jump phenomenon in in-plane of flexible circular cantilever beam, because of non-linear coupling. In addition, cantilever beam showed hardening spring characteristics in in-plane and softening spring characteristics in out-of-plane.

• Korean Journal of Materials Research
• /
• v.17 no.2
• /
• pp.121-123
• /
• 2007

Energy harvesting from the vibration through the piezoelectric effect has been studied for powering the wireless sensor node. As piezoelectric unimorph cantilever structure can transfer low vibration to large displacement, this structure was commonly deployed to harvest electric energy from vibrations. Piezoelectric unimorph structure was composed of small stiff piezoelectric ceramic on the large flexible substrate. As there is the large Young's modulus difference between the flexible substrate and stiff piezoelectric ceramic, flexible substrate could not homogeneously transfer the vibration to stiff piezoelectric ceramic. As a result, most piezoelectric ceramics had been broken at the certain point. We measured and analyzed the stress distribution on the piezoelectric ceramic on the cantilever.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.129-133
• /
• 2004

This paper is the result of a experimental study about non-linear one to one modal coupling of a flexible circular cantilever beam which was transversely excited with harmonic excitation. It was proved that 2 order jumping in out of plane was caused by jump phenomenon in in-plane of flexible circular cantilever beam, because of non-linear coupling. In addition, cantilever beam showed hardening spring characteristics in in-plane and softening spring characteristics in out-of-plane.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.1
• /
• pp.3-10
• /
• 2008

In this paper, the optimal command input is considered in order to minimize the residual vibrations of a flexible cantilever beam when the beam simply changes its position by translation or rotation. Although a cantilever beam has many modes of vibration, it is shown that the consideration of the first mode is sufficient in this case. Thus, the problem becomes a single-degree-of-freedom system subjected to a ground excitation. Two simple methods are proposed to find the optimal command input based on the shock response spectrum (SRS). The first method is the simplest and can be applied to lightly damped cases, and the second method is applicable to more general problems. The second method gives almost the same results as the input shaping method. However the proposed method gives a easier and clearer control strategy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.257-258
• /
• 2009

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.1
• /
• pp.30-41
• /
• 2004

This paper is concerned with the active vibration control of flexible cantilever beam system using electromagnetic farce actuator. The main objective of this paper is to propose the control algorithms and to implement the experimental setups for active vibration control. Dynamic equations of the electromagnetic actuator and the beam are combined to find the transfer function from the electromagnetic actuator to the laser sensor. The final transfer function is determined by considering only the first and second modes, and experiments confirm that this model works well. Several control algorithms are proposed and implemented on the experimental setups to show their efficacy. These include a PID control design, an optimal H$_2$ control design, and a fuzzy PID control design. Effectiveness and performance of the designed controller were verified by both simulation and experiment results.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2073-2075
• /
• 2003

This paper presents the active vibration control of flexible cantilever beam using piezoceramic actuators. The transfer function from the force input to the bending displacement was obtained via modal analysis results and piezoelectric constitutive equations. For the active vibration control piezoceramic actuators and sensors were used to construct a flexible smart cantilever beam. To further enhance the sensing and actuation properties of the piezoceramics, a typical interdigitated electrode pattern was fabricated. The PID controller was designed via various simulation and experiment trials. It was shown that the PID controller could suppress vibration of the beam effectively. Simulations and experiments verified good performances of the designed controller.