• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.4
• /
• pp.435-442
• /
• 2016

For inertial navigation systems, initial information such as position, velocity and attitude is required for navigation. Self-alignment is the process to determine initial attitude on stationary condition using inertial measurements such as accelerations and angular rates. The accuracy of self-alignment is determined by inertial sensor error. As soon as an inertial navigation system is powered on, the temperature of accelerometer rises rapidly until temperature stabilization. It causes acceleration error which is called temperature stabilizing error of accelerometer. Therefore, temperature stabilizing error degrades the alignment accuracy and also increases alignment time. This paper suggests a method to calculate azimuthal attitude using curve fitting of horizontal control angular rate in fixed-gain self-alignment. It is verified by simulation and experiment that the accuracy is improved and the alignment time is reduced using the proposed method under existence of the temperature stabilizing error.

• KIPS Transactions on Software and Data Engineering
• /
• v.6 no.2
• /
• pp.91-102
• /
• 2017

Many of the wearable smart fitness devices provide services related to users' heartbeat rates. These services use fixed standards which have been pre-determined based on statistical data. However, because body conditions significantly differ between individuals, the services applying fixed standards to all individuals are not reliable. This paper proposes the Feedback-RFC model which adapts heartbeat standards to individual users' exercise abilities and also proposes a method to implement the model. This paper also shows the effectiveness of the Feedback-RFC model by collecting heartbeat data from 12 participants and evaluating the model with the data.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.109-114
• /
• 2009

The dominant heating system used in Korean residential apartment buildings is a hydronic radiant floor heating system, known as the Ondol system. The most common control strategy applied to this traditional hydronic radiant system is a simple on-off control that intermittently supplies "hot water of a fixed temperature" at a "constant flow rate" to each room. However, the current problems with the aforementioned control are as follows: (1) since the simple on-off control is usually based on a one point measured temperature (a signal from a thermostat installed in a living room) in each dwelling unit, heating energy use for unoccupied rooms as well as a difference in temperatures between spaces (master bedroom, living room, bedroom1, bedroom2) can occur occasionally. (2) the most widely used residential water splitter has static valves, and is thus not able to change the flow rate to each room depending on the space heating load. In other words, the ratio of flow rates to rooms is fixed after construction, resulting in over- or under-heating and an improper use of energy. The aim of this paper is therefore to investigate the differences in the system's performance between control strategies in terms of the flow rate control and sensor location. It is shown that energy savings of control strategies are strongly influenced by occupant schedule.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.27-30
• /
• 2003

The introduction of reseller In Australian Fixed Telecommunication Market resulted in the reduction of Telstra's local call market share by 13 percent and average fall rate was reduced. Thus, Telstra increased basic rate at 14.5 percent to compensate loss revenue in the local call market. With the deployment of carrier pre-selection of long distance and international calls, it reduced long distance rate at 23.5 percent and international tall rate at 53 percent, and increased the Churn rate. Therefore, the deployment of service-based competition brought efficient results for long distance and international call market. However, LM market created 13.4 percent reduction in call rates, complications in charge system, technical barriers and the preference of one-bill by customers.

• The Journal of Asian Finance, Economics and Business
• /
• v.7 no.7
• /
• pp.229-239
• /
• 2020

This article aims to measure the impact of economic growth and urbanization on poverty reduction in Vietnam, and verify whether economic growth and urbanization will help reduce poverty rates. Data for this study are tabular data related to growth, urbanization and poverty at the provincial level for the period of nine years, from 2006 to 2014 provided by the Vietnam General Statistics Office and the Vietnam General Department of Customs. The level of economic growth and urbanization mentioned in the study is reflected in such indicators as GDP value, exports value, imports value, urbanization rate and employment rate. The authors used logistic regression models with fixed-effects and logistic regression models with random effects. With 5% confidence level tested by the Chi-Square test of Hausman trial with the fixed-effect model, research results show that: (1) factors with significant negative impact on the poverty rate include imports value, urbanization rate and, employment rate; (2) factors that do not affect the poverty rate include exports value and GDP value. Based on the research results, this study proposes a number of policy recommendations to help promote economic growth, to sustain the urbanization process, and to contribute directly and positively to poverty reduction in Vietnam.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.7
• /
• pp.564-568
• /
• 2003

The etching of Au thin films have been performed in an inductively coupled CF$_4$/Cl$_2$/Ar plasma. The etch rates were measured as CF$_4$ contents added from 0 to 30 % to Cl$_2$/Ar plasma, of which gas mixing ratio was fixed at 20%. Other parameters were fixed at an rf power of 700 W, a dc bias voltage of 150 V, a chamber pressure of 15 mTorr, and a substrate temperature of 3$0^{\circ}C$. The highest etch rate of the Au thin film was 3700 $\AA$m/min at a 10% additive CF$_4$ into Cl$_2$/Ar plasma. The surface reaction of the etched Au thin films was investigated using x-ray photoelectron spectroscopy (XPS) analysis. XPS analysis indicated that Au reacted with Cl and formed Au-Cl, which is hard to remove on the surface because of its high melting point. The etching products could be sputtered by Ar ion bombardment.

• Proceedings of the KIEE Conference
• /
• 1996.07b
• /
• pp.1295-1297
• /
• 1996

CCITT G.721, G.723 standard ADPCM algorithm is implemented by using TI's fixed point DSP start kit (DSK). ADPCM can be implemented on a various rates, such as 16K, 24K, 32K and 40K. The ADPCM is sample based compression technique and its complexity is not so high as the other speech compression techniques such as CELP, VSELP and GSM, etc. ADPCM is widely applicable to most of the low cost speech compression application and they are tapeless answering machine, simultaneous voice and fax modem, digital phone, etc. TMS320C50 DSP is a low cost fixed point DSP chip and C50 DSK system has an AIC (analog interface chip) which operates as a single chip A/D and D/A converter with 14 bit resolution, C50 DSP chip with on-chip memory of 10K and RS232C interface module. ADPCM C code is compiled by TI C50 C-compiler and implemented on the DSK on-chip memory. Speech signal input is converted into 14 bit linear PCM data and encoded into ADPCM data and the data is sent to PC through RS232C. The ADPCM data on PC is received by the DSK through RS232C and then decoded to generate the 14 bit linear PCM data and converted into the speech signal. The DSK system has audio in/out jack and we can input and out the speech signal.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.2
• /
• pp.186-195
• /
• 2015

This study aims at modeling the rotary drying of wood chips in co-current mode and estimating the drying time of larch (Larix kaemferi) wood chip. Drying data were obtained in a lab. scale fixed bed dryer operating with an air velocity of 1 m/sec. and at hot air inlet temperatures of $100^{\circ}C$, $200^{\circ}C$, and $300^{\circ}C$. The lab. scale fixed-bed drying rates for small, medium and large size larch wood chips that had been dried from 40% wet-based moisture content (MC) to 10% MC at $200^{\circ}C$ drying temperature were 17.3 %/min., 10.2 %/min. and 5.5 %/min., respectively. It was predicted that larch large size wood chips could be dried from 40% MC to 10% MC in about 23.0, 34.6, and 44.7 minutes at $300^{\circ}C$, $200^{\circ}C$ and $150^{\circ}C$, respectively. Expected drying times for medium size chips were about 8.6, 11.2 and 13.2 minutes and those for small size chips were 4.3, 5.5 and 6.4 minutes, respectively.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.2
• /
• pp.170-176
• /
• 2017

In this paper, we propose an underwater localization scheme through the fusion of an inertial navigation system (INS) and the received signal strength (RSS) of electromagnetic (EM) wave sensors to guarantee precise localization performance with high sampling rates. In this localization scheme, the INS predicts the pose of the unmanned underwater vehicle (UUV) by dead reckoning at every step, and the RF sensors corrects the UUV position functions using the Earth-fixed reference when the UUV is located in underwater wireless sensor networks (UWSN). The localization scheme and state modeling were conducted in the extended Kalman filter framework, and UUV localization experiments were conducted in a basin environment. The scheme achieved reliable localization accuracy during long-term navigation, demonstrating the feasibility of exploiting EM wave attenuation as Earth-fixed reference sensors.

• Nuclear Engineering and Technology
• /
• v.54 no.8
• /
• pp.3017-3026
• /
• 2022

The ¹³¹Cs radioisotope with a short half-life time and high average radiation energy can treat the cancer effectively in prostate brachytherapy. The typical ¹³¹Cs production processes have a separation step of the cesium from ¹³¹Ba to obtain a high specific radioactivity. Herein, we suggested a novel ¹³¹Cs separation method based on the Ba²⁺ adsorption of alginate beads. It is necessary to reduce the affinity of alginate beads to cesium ions for a high production yield. The carboxyl group of the alginate beads was replaced by a sulfonate group to reduce the cesium affinity while reinforcing their affinity to barium ions. The modified beads exhibited superior Ba²⁺ adsorption performances to native beads. In the fixed-bed column tests, the saturation time and adsorption capacity could be estimated with the Yoon-Nelson model in various injection flow rates and initial concentrations. In terms of the Cs elution, the modified alginate showed better performance (i.e., an elution over 88%) than the native alginate (i.e., an elution below 10%), indicating that the functional group modification was effective in reducing the affinity to cesium ions. Therefore, the separation of cesium from the barium using the modified alginate is expected to be an additional option to produce ¹³¹Cs.