• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.5
• /
• pp.44-53
• /
• 1999

This paper are reported a methodology and application for extracting parasitic capacitances in a multi-level interconnect semiconductor structure by a numerical technique. To calculate the parasitic capacitances between the interconnect lines, we employed finite element method (FEM) and calculated the distrubution of electric potential in the inter-metal layer dielecric(ILD) by solving the Laplace equation. The three-dimensional multi-level interconnect structure is generated directly from two-dimensional mask layout data by specifying process sequences and dimension. An exemplary structure comprising two metal lines with a dimension of 8.0$\times$8.0$\times$5.0$\mu\textrm{m}^3/TEX>, which is embedded in three dielectric layer, was simulated to extract the parasitic capacitances. In this calculation, 1960 nodes with 8892 tetrahedra were used in ULTRA SPARC 1 workstation. The total CPU time for the simulation was 28 seconds, while the memory size of 4.4MB was required.

• Journal of the Korean Magnetics Society
• /
• v.26 no.3
• /
• pp.86-91
• /
• 2016

The cogging torque of a brushless dc (BLDC) motor results from the interaction between permanent magnets and iron core, and it causes noise and induce vibrations. During a manufacturing process, assembly tolerances lead to the change of the electromagnetic structure of a BLDC motor where permanent magnets are not properly glued to the surface of rotor core. In this paper, the effect of magnet separation from the surface of rotor core on the cogging torque is investigated due to assembly tolerance. The relationship with key design parameters is considered such as separation between magnets and rotor core, the number of magnets having separation, as well as the several types of arrangements among neighboring magnets. Finite element method (FEM) has been used to analyze a BLDC motor, and the allowable assembly tolerance is proposed to prevent generating noise and vibrations. Within proposed assembly tolerance, it is concluded that the cogging torque of a BLDC motor is decreased, and hence noise and vibrations.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.33-39
• /
• 2020

Typically, photoacoustic images are obtained in water or gelatin because the impedance of these mediums is similar to that of the human body. However, these acoustic mediums can have an additional mass effect that changes the resonance frequency of the transducer. The acoustic radiation impedance in air is negligible because it is very small compared to that of the transducer. However, the high acoustic impedance of mediums such as the human body and water is quite large compared to that of air, making it difficult to ignore. Specifically, in a case where the equivalent mass is very small, such as with a micro-machined ultrasound transducer, the additional mass effects of the acoustic medium should be considered for an accurate resonance frequency design. In this study, a piezoelectric micro-machined ultrasonic transducer (pMUT) was designed to have a resonance frequency of 10 MHz in the acoustic medium of water, which has similar impedance as the human body. At that time, the resonance frequency of the pMUT in air was calculated at 15.2 MHz. When measuring the center displacement of the manufactured pMUT using a laser vibrometer, the resonance frequencies were measured as 14.3-15.1 MHz, which is consistent with the finite element method (FEM) simulation results. Finally, photoacoustic images of human hair samples were successfully obtained using the fabricated pMUT.

• The Journal of Korean Physical Therapy
• /
• v.13 no.1
• /
• pp.1-18
• /
• 2001

Aging has been recognized as the primary cause of disc degeneration. A biomechanical characteristics of disc degeneration has been demonstrated that intradiscal pressure is reduced. With the increasing population of elderly people, disc degeneration and associated problems of nerve entrapment are becoming more prevalent. Presently, research on reduced intradiscal pressure associated with degeneration is insufficient. In this study. we used the Finite Element Method (FEM) of computerized simulations to investigate the effects of variation in intradiscal pressure on mechanical behaviours of L4-5 intervertebral disc degeneration. Degeneration was classified using four grades based on initial intradiscal pressure; Normal (135 kPa), mild(107 kPa), moderate (47 kPa) and severe (15 kPa). The predicted results f3r bending loads were as follows; 1 . Range of motion increased progressively with severity of degeneration with flexion and lateral bending moments, but decreased with extension moments. 2. Discal bulging of posterolateral aspect was larger in lateral bending and extension moment. But bulging was increased with severity of degeneration in lateral bending and torsion(same side).3. The rate of increasing intradiscal pressure was decreased in all bending motions with severity of degeneration. In conclusion, lateral bending and extension moment yield greatest bulging in severe degeneration. In torsion, although bending load produces disc bulging, disc bulging was associated more strongly with severity of degeneration than increasing torsional moments. Clinical Implications: Discal bulging may produce nerve root impingement and irritation. The effect of loading and posture on the varying degrees of disc degeneration has important implications especially in the elderly. In the presence of disc degeneration, avoidance of end range postures, especially extension and lateral bending may help reduce discal bulging and in turn, nerve entrapment.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.911-916
• /
• 2012

It is important to identify dynamic characteristics of nuclear fuel components. Since the fuel always exposed to turbulent flow, the dynamic contact between grids and rods is one of the fuel failure modes. The dynamic behavior of grids in nuclear fuels is quite complex, since two pairs of spring support are placed in the limited space. The strap in a cell has single spring and double dimples and this paper focuses on investigation of the grid strap(Test Fuel Strap, TFS) vibration in one cell. To identify the grid strap vibration, modal analysis of the strap is performed using Finite Element Method (FEM). Modal testing on a $5{\times}5$ grid structure without rods is performed. The modal testing results are compared to analytic results. In addition, random test considering rod effect is performed about a $5{\times}5$ grid with rods under real contact condition in the air. Finally, the strap vibration of a $5{\times}5$ fuel bundle in INvestigation of Flow INduced vIbraTion(INFINIT) facility is measured in real fluid velocity condition without heating. It is shown that modal frequencies from the test are almost equal to those peak frequencies in the INFINIT test.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.7
• /
• pp.7-16
• /
• 2000

This paper reports a methodology and its application for extracting cell capacitances and parasitic capacitances in a stacked DRAM cell structure by a numerical technique. To calculate the cell and parasitic capacitances, we employed finite element method (FEM), The three-dimensional DRAM cell structure is generated by solid modeling based on two-dimensional mask layout and transfer data. To obtain transfer data for generating three-dimensional simulation structure, topography simulation is performed. In this calculation, an exemplary structure comprising 4 cell capacitors with a dimension of $2.25{\times}1.75{\times}3.45{\mu}m^3$, 70,078 nodes with 395,064 tetrahedra were used in ULTRA SPARC 10 workstation. The total CPU time for the simulation was about 25 minutes, while the memory size of 201MB was required. The calculated cell capacitance is 24.34fF per cell, and the influential parasitic capacitances in a stacked DRAM cell are investigated.

• Journal of the Korean Institute of Gas
• /
• v.18 no.2
• /
• pp.10-15
• /
• 2014

In this paper, the displacement and stress strength safeties have been presented for cylindrical hollow rollers of a wire saw machine. Using the finite element method, the hollow roller with Y-shaped shift and vertical columns between three tubes has been developed to analyze the displacement behavior and stress strength safeties. For the same diameter and length of hollow roller models with a different weight, the displacement behavior safety of Y-shaped shift column and vertical column models is heavily depending on the total length of a hollow roller, which is closely related to the bending moment of a hollow roller structure. But, the stress strength of a hollow roller is more influenced by the cross sectional area of a hollow roller for the similar weight. Thus, this paper recommends Y-shaped hollow roller for increasing the roller strength safety and decreasing a total roller weight.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.12
• /
• pp.1668-1677
• /
• 2013

This paper deals with the power loss and thermal characteristics of induction motor for machine tools according to the rated power and speed. To reduce the fabrication error by thermal strain in rotational machine tools, we calculated the power loss and thermal behavior of induction motors. Firstly, the inverse design of general induction motors for machine tool spindle has been performed. The inverse design results are compared with the torque-speed characteristic curve in motor's catalog. The power loss are calculated by finite element method(FEM) at rated condition. Secondary, the transient thermal characteristics of induction motors are calculated by equivalent thermal resistance model from Motor-CAD S/W. The inverse design, power loss and thermal behavior calculation for induction motors with various rated power and speed has been performed. Finally, to verify the design and calculation process of induction motor, we implemented the experimental set with 0.4kW 1710rpm class industrial induction motor model. The obtained thermal characteristics of experimental model confirmed that the design and power loss calculation processes are appropriate to the prediction of thermal strain in rotational machine tools.

• Steel and Composite Structures
• /
• v.22 no.5
• /
• pp.937-974
• /
• 2016

While extensive efforts have been made in the past to develop finite element models (FEMs) for concrete-filled steel tubular columns (CFSTCs), these models may not be suitable to be used in some cases, especially in view of the utilisation of high strength steel and high strength concrete. A method is presented herein to predict the complete stress-strain curve of concrete subjected to tri-axial compressive stresses caused by axial load coupled with lateral pressure due to the confinement action in square and rectangular CFSTCs with normal and high strength materials. To evaluate the lateral pressure exerted on the concrete in square and rectangular shaped columns, an accurately developed FEM which incorporates the effects of initial local imperfections and residual stresses using the commercial program ABAQUS is adopted. Subsequently, an extensive parametric study is conducted herein to propose an empirical equation for the maximum average lateral pressure, which depends on the material and geometric properties of the columns. The analysis parameters include the concrete compressive strength ($f^{\prime}_c=20-110N/mm^2$), steel yield strength ($f_y=220-850N/mm^2$), width-to-thickness (B/t) ratios in the range of 15-52, as well as the length-to-width (L/B) ratios in the range of 2-4. The predictions of the behaviour, ultimate axial strengths, and failure modes are compared with the available experimental results to verify the accuracy of the models developed. Furthermore, a design model is proposed for short square and rectangular CFSTCs. Additionally, comparisons with the prediction of axial load capacity by using the proposed design model, Australian Standard and Eurocode 4 code provisions for box composite columns are carried out.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.6
• /
• pp.57-65
• /
• 2001

In this paper, we designed the acoustic horn for magnetostrictive ultrasonic transducers in a theoretical manner, and validity of the analysis was verified through comparison with the results of finite element analysis. Results of the two analysis methods showed good agreement with each other. The theoretical method can fairly quickly determine the horn length that satisfies given frequency specification, but also has the drawback that it is applicable only to the frequency range over the cut-off frequency. According to the results, the catenoidal horn can provide larger amplification than the exponential horn. It was also found that it is more desirable for the region having the catenoidal curvature to be as short as possible to achieve larger amplification of the transducer deformation. Based on the analysis results, a magneto-strictive transducer sample was fabricated and its performance was evaluated experimentally. The transducer has the resonance frequency of 19.3 ㎑ as well as the maximum SPL of 199 dB, and shows the omni-directional radiation pattern.