• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.5
• /
• pp.125-132
• /
• 2000

This study was performed to evaluate the physical properties of reinforced soil mixture powder. Soil sample was prepared by passing into the standard sieve of No. 200 and reinforcement materials were calcium carbonate, quicklime and portland cement. Fineness, setting time, and compressive strength test for reinforced soil mixture powder were performed and analyzed to investigate their physical properties. The main results were summarized as follow. The compressive strength of soil mixture powder itself and most reinforced was reinforced according to increasing in the mixture rate of reinforcement and the rate of increase was remarkably higher in the cement reinforced soil moisture powder. It was appeared that the early compressive strength is considering higher in the cement reinforced soil moisture powder with 2% of moisture rate of accelerator.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.186-187
• /
• 2013

Recently, high fluidity concrete is becoming more prevalent. High fluidity concrete uses admixture or thickener in order to prevent separation of materials due to increased fluidity, and, especially, BS is becoming more use for reduced heat of hydration and improved long-term strength. This study examined the effect of BS on fluidity of cement paste from a rheological viewpoint. As for BS types, materials equivalent to 1 types of KS F 2563 and the cement mass was substituted by 20, 40, 60, 80%.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.144-149
• /
• 2000

Porous cement concrete was developed to prevent hydroplaning of airway pavement or to reduce noise emission in highway. In has been introduced in domestic since early 1980' and applied to a pedestrian road or bike way. The concrete, however, has problems such as lack of optimized mix design, low strength and deterioration, etc. The purpose of this study is to manufacture porous cement concrete using blast-furnace slag to enhance mechanical properties. The results of this study are as follows; the compressive strength range is 102∼247kgf/㎠, the tensile strength range is 16∼70kgf/㎠, the bending strength range is 43∼70kgf/㎠, and the coefficient permeability range is 6.79 ×10-2∼1.17∼10-1cm/sec. To develope high-performance porous concrete, further studies are needed on optimum mixture of fineness modulus and admixture.

• Computers and Concrete
• /
• v.11 no.1
• /
• pp.39-49
• /
• 2013

The use of ground fly ash in concrete can increase the risk of slump loss due to the drastic surface change of the particles after the grinding treatment and the accelerated reaction compared to the untreated ash. This study is aimed at the early age hydration and time-dependent rheology changes of cement paste containing ground fly ash. An original fly ash is ground into different fineness and the hydration of cement paste containing the ground fly ash is monitored with the ultrasound propagation method. The zeta potentials of the solid particles are measured and the changes of rheological parameters of the cement pastes with time are analyzed with a rheometer. A particle packing model is used to probe packing of the solid particles. The results show that the early age hydration of the paste is strongly promoted by replacing Portland cement with fly ash up to 30 percent (by mass), causing increase of the yield stress of the paste. The viscosity of a paste containing ground fly ash is lower than that containing the untreated ash, which is explained by the denser packing of the solid particles.

• Journal of the Korean Ceramic Society
• /
• v.56 no.5
• /
• pp.468-473
• /
• 2019

This study focused on manufacturing an inorganic insulation material set with various amounts of calcium-sulfoaluminate (CSA) (hauyne) content for enhancing both workability (demolding, handling) and the high thermal insulating property. To carry out the experiment, the amounts of CSA utilized were 5%, 10%, 15%, and 20%, with anhydrous gypsum added in equal proportion to produce a stable formation. As the content of CSA increased, a sinking phenomenon occurred because of the hydration reaction from the slurry, so it was difficult to utilize a retarder normally used in the cement manufacturing process. However, an RCOOM surfactant was able to solve the local clumping problem from cement and CSA and obtain a rapid retarding effect, so it was included in this process at 0.3%. Furthermore, the cement fineness was not 7000 ㎠/g but rather 3300 ~ 4000 ㎠/g to prevent a rapid temperature increase in the slurry. The specific gravity of the sample manufactured with 20% CSA was approximately 0.11 g/㎤, and its thermal conductivity was 0.041 W/m·K, providing an excellent insulating property.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.10a
• /
• pp.138-143
• /
• 1993

The objective of this report is to investigate the effect of factors like the fineness modulus of sand , content of fly ash and slaked lime, binder/sand ratio, admixture dosage on the physical properties of mortar for finishing. The analysis was performed with design of experiment and air content, water retention and compressive strength were measured.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.150-151
• /
• 2021

This study aims to achieve an enhancement in the quality of high strength concrete through a reduction in autogenous shrinkage by supplying the moisture needed for hydration through recycled aggregates that retain high amounts of moisture. The result showed that, moisture supply increased with the higher replacement rate, autogenous shrinkage dropped by up to 45 percent.

• Smart Structures and Systems
• /
• v.22 no.4
• /
• pp.425-432
• /
• 2018

Predicting the compressive strength of concrete has been considered as the initial phase across the cement production processing. The current study has focused on the integration of the concrete compressive strength in 28 days with the mix of the major oxides and fine aggregates as an experimental formula through the use of two types of Portland cement resulting the compressive strength of the concrete highly dependent on time.

• Computers and Concrete
• /
• v.8 no.5
• /
• pp.583-595
• /
• 2011

This paper studied the cement efficiency factor (k factor) of high calcium Class F fly ash. This k factor represents a unit of fly ash with efficiency equivalent to k unit of cement. The high calcium Class F fly ash was used to replace cement in concrete. The modified Bolomey's law with linear relationship was used for the analysis of the result of compressive strength, cement to water ratio (c/w) and fly ash to water ratio (f/w) by using the multi-linear regression to determine the k factor and other constants in the equations. The results of analysis were compared with the results from other researcher and showed that the k factor of high calcium Class F fly ash depends on the fineness of fly ash, replacement level and curing age. While the amount of CaO content in Class F fly ash not evident. Furthermore, necessary criteria and variables for the determination of the k factor including the use of the k factor in concrete mix design containing fly ash were proposed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.193-194
• /
• 2017

In this research, the density value of the turbid solution is measured by using the principle of inexpensive but easy Hydrometer method for cement delivered to the actual raw concrete plant, By analyzing the correlation of powder aid, we will try to present a scheme that can be utilized as a method of acquisition acquisition inspection. As a result of the analysis, it was found that there was a large difference between the measured powders assisted with cement powder on the report, and the correlation with the actually measured powder aid Hydrometer density value was good. Therefore, using the method of Fig. 3, it was possible to know that the degree of powder quality of cement delivered to the raw concrete factory can be evaluated quickly and utilized at the time of argument inspection.