• Composites Research
• /
• v.30 no.5
• /
• pp.267-272
• /
• 2017

In this study, SiC powder was added to twill woven carbon fiber reinforced plastic (CFRP) composites to improve its mechanical properties. An acoustic emission (AE) frequency analysis method was suggested for the prediction of failure behaviors. Tensile tests were conducted and the fracture characteristics of each component of the SiC reinforced composite were evaluated using AE. The results showed that SiC powder improved the strength of twill woven CFRP composites and the fracture behavior of the SiC reinforced CFRP composite and its crack extension could be effectively evaluated on the basis of the specific AE frequency bands which are 100 to 228 kHz and 428 to 536 kHz upon the resin failure and 232 to 424 kHz due to addition of SiC powder and 576 to 864 kHz at the fiber breakage.

• Journal of Power System Engineering
• /
• v.9 no.2
• /
• pp.57-64
• /
• 2005

This paper is the study on dry sliding wear behavior of carbon fiber reinforced epoxy matrix composites against lay-up orientation. Tests were investigated on the effect of the lay-up orientation, fiber sliding direction, load and sliding velocity when circumstance keep continuously at $21^{\circ}C$, 60%RH. Pin-on-disk dry sliding wear tests for each experimental condition were carried out with a carbon fiber reinforced plastic pin on stainless steel disk in order to search the friction and wear characteristics. The wear rates and friction coefficients against the stainless steel counterpart were experimentally determined and the wear mechanisms were microscopically observed. The effect on friction and wear behavior are observed differently, according to various conditions. When sliding took place against counterpart, the highest wear resistance and the lowest friction coefficient were observed in the $[0]_{24s}$ lay-up orientation at anti-parallel direction.

• The Research Journal of the Costume Culture
• /
• v.9 no.4
• /
• pp.629-638
• /
• 2001

This study was intended to identify the desired image and fabric preference of woman college student for apparel and the relationship between these variables. Data were collected by questionnaire distributed to 260 woman college students through August to September of 2000. After eliminating incomplete questionnaires, 236 were analyzed. The most desired image was neat, and the most preferred fabric was natural fiber textile in fiber contents and light and soft in fabric sensation. The avoided image was masculine, and the negative sensation was heaviness. As a result of factor analysis, 7 factors -cute, intellectual, animate, neat, mature, sporty, sexy- were determined in image. And 8 factors -soft, durable, flat, rigid, light, bulky, heavy, pliable- were determined in fabric sensation. These factors explained large percentage of variance respectively. Multidimensional scaling was employed to analyze the relationship between desired image and fabric preference. Two dimensions were accepted to interpret the relationship. One of the results showed the closeness among the natural fiber textile, lightness, durability and natural image. And the short distance among the blended textile, elasticity, warmness and sporty image was presented.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.65-68
• /
• 2001

In this research, damage initiation in singly oriented ply (SOP) FML under concentrated loading conditions was studied. The finite element method (FEM) base on the first order shear deformation theory is used for the analysis of fiber orientation effect on FML under concentrated loading conditions. The failure indices were calculated for the variation of fiber orientation and the results were compared with indentation experiments. The failure indices were well matched with damage initiation of SOP FML. Indentation results shows that the crack initiation of SOP FML is determined by stiffness induced by fiber orientation and tile penetration load of SOP FML are influenced by the deformation tendency and boundary conditions.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.81-86
• /
• 2001

The concrete bridge decks are in need of replacement and rehabilitation due to decreasing load carrying capacity. In this study, to propose a strengthening technique that improves usability and structural performance of the bridge deck and to propose an efficient strengthening design technique which satisfies both the strength End serviceability of the bridge deck, this paper shows the failure characteristics of the strengthened bridge decks and proposes an empirical yield criterion. Therefore, strengthening efficiency was proposed based on the experiment and yield line analysis result. The yield line theory which adopts the modified criteria of Johansen is considered to predict the ultimate strength about all strengthening material(Carbon Fiber Sheet, Carbon Fiber Rod, Grid Type Carbon Fiber).

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.359-362
• /
• 2002

이산화탄소($CO_2$)를 사용한 셀룰로오스 카보네이트 유도체의 제조 및 재생 셀룰로오스 섬유 제조와 관련한 기초 연구성과를 이미 발표한 바 있다[1~4]. 이번 연구에서는 일정한 조건에서 제조된 셀룰로오스 카보네이트 유도체를 10 wt% NaOH 수용액계에 용해시켜 방사용액(spinning dope)을 제조하고 일욕의 습식 방사장치를 이용하여 재생 셀룰로오스 섬유를 제조하였다. 이때 사용된 응고욕으로 황산, 초산, 인산 수용액계를 사용하였으며 제조된 각각의 재생 셀루로오스 섬유에 대해 물성분석을 하였다. (중략)

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.9-12
• /
• 2005

Recently, research on the morphing wing is an interesting issue to develop the capability of the wing such as improving the lift and reduction of drag during the operation of an aircraft by changing the wing shape from one configuration to another. A more efficient weight reduction of the wing using smart or morphing wing concept can be achieved in comparison with the conventional flaps. In this study, it is investigated the behaviors of the morphing wing using Macro Fiber Composite (MFC) actuators. Generally, MFC is the piezocomposite actuator with the rectangular PZT fiber and epoxy matrix, and uses the interdigitated electrode to produce more powerful actuation in the in-plane direction. Furthermore, it can produce the twisting actuation as compared with the traditional PZT actuators. In the formulation, the first-order shear deformation plate theory is used, and finite element method is adopted in the numerical analysis of the model. Results show the characteristics of the static behavior of the morphing wing according to the change of the actuation voltage.

• Carbon letters
• /
• v.2 no.3_4
• /
• pp.170-175
• /
• 2001

A petroleum-based isotropic pitch fiber spun by melt-blown method was oxidized in air flow at various conditions. The oxidized pitch fiber obtained was tested for its infusibility and its elemental composition during the process of stabilization. The structural changes were traced by using solvent solubility, FT-IR spectroscopy, and elemental analysis. The samples showed a gradual increase in weight with increasing the oxidization temperature. The weight gain of sample oxidized at $320^{\circ}C$ for 10 min was about 4.5%. The concentration of the pyridine and toluene soluble fraction decreased with an increase in stabilization temperatures. The oxygen uptaken in the stabilization process converted aliphatic side chains into the carbonyl groups. As stabilization proceeded, the more ether and carboxylic acid groups were formed through the oxidations of aldehyde and primary alcohol, and then the carboxylic acid was dehydrated to be aromatic anhydride.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.840-843
• /
• 2004

UV molding is a process for integrating micro/nano polymeric optical components on optoelectronic modules. In the present study, a microlens array for vertical cavity surface emitting laser(VCSEL) to fiber coupling was designed, integrated and tested. At the design stage, design variables ware optimized to maximize the coupling efficiency, and tolerance analysis was carried out. At the integration stage, the UV transparent mold was fabricated and the microlens array on VCSEL array was integrated by UV molding process. Finally the coupling efficiency of VCSEL to fiber was measured and analyzed.

• Computational Structural Engineering
• /
• v.9 no.4
• /
• pp.181-187
• /
• 1996

This paper concerns the singular thermal stresses at the interface corner between the elastic fiber and the viscoelastic matrix of a two-dimensional unidirectional laminate model induced during cooling from cure temperature down to room temperature. Time-domain boundary element method is employed to investigate the nature of residual thermal stresses at the interface. Numerical results show that very large stress gradients are present at the interface corner and such stress singularity might lead to local yielding or fiber-matrix debonding.