• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.6
• /
• pp.433-438
• /
• 2020

To enhance the tunneling electroresistance (TER) ratio of a ferroelectric tunnel junction (FTJ) device using Al-doped HfO₂ thin films, a thin insulating layer was prepared on a TiN bottom electrode, for which TiN was preliminarily treated at various temperatures in O₂ ambient. The composition and thickness of the inserted insulating layer were optimized at 600℃ and 50 Torr, and the FTJ showed a high TER ratio of 430. During the heat treatments, a titanium oxide layer formed on the surface of TiN, that suppressed oxygen vacancy generation in the ferroelectric thin film. It was found that the fabricated FTJ device exhibits two distinct resistance states with higher tunneling currents by properly heat-treating the TiN bottom electrode of the HfO₂-based FTJ devices in O₂ ambient.

• Journal of the Korean Ceramic Society
• /
• v.33 no.6
• /
• pp.665-671
• /
• 1996

Ferroelectric Pb(Fe1/2Nb1/2)O3 thin films were successfully fabricated on ITO/Glass substrate by sol-gel proces-sing and characterized to determine the dielectric and electric properties. Viscosity of PEN sol measured to investigate rheological properties was 3.25 cP which was proper for coating. The sol also showed Newtonian behavior. RTA(Rapid Thermal Annealing) was used for the annealing of the thin film and 1200~1700$\AA$ thick PEN thin films were fabricated by repeating the intermediate and the final annealing. After the deposition of Pt as top electrode by vacuum evaporation dielectric and electric properties were measured. Dielectric properties of FFN thin film were enhanced by increasing the perovskite phase fraction with increasing the annealing temperature. Measured dielectric constant of 1700$\AA$ PFN thin film annealed at $650^{\circ}C$ was 890 at 1kHz Capacitatnce density and dielectric loss were 47 fF/${\mu}{\textrm}{m}$2 and 0.47 respectively. As a result of measuring Curie temperature PFN thin films had Curie point with a rang of 110~12$0^{\circ}C$ and showed broad dielectric peak at that point. Leakage current of the PFN thin films were increased with increasing the annealing tempera-ture.

• Journal of the Korean Ceramic Society
• /
• v.34 no.4
• /
• pp.373-379
• /
• 1997

A study on the deposition and characterization of BaTiO3 thin films on MgO-buffered Si(100) substrates by sputtering was conducted. The MgO buffer layers were investigated as a function of deposition temperature. At lower substrate temperature, the MgO layers were not fully crystalline, but a crystallized MgO layer with (001) preferred orientation was obtained at the substrate temperature of $700^{\circ}C$. Partially (00ι) or (h00) textured BaTiO3 films were obtained on Si(100) with the MgO buffer layer grown at 700ι. While, randomly oriented BaTiO3 films with large-scale cracks on the surface were made without the MgO layer. The crystallographic orientation, morphology and electrical properties between the BaTiO3 films on Si with and without the MgO layer were compared using the BaTiO3 film on MgO(100) single crystal substrate as a reference system. Also the favorable role of the MgO layer as a buffer for growing of oriented BaTiO3 films on Si substrates was confirmed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.305-308
• /
• 2003

We fabricated a flexible ferroelectric liquid crystal (FLC) device containing polymer walls and networks which fix plastic film substrates. The device using 100-${\mu}m$-thick substrates could be bent in a radius of 7mm without disordering the FLC alignment. When sandwiched between polarizers a roll-up display with high-speed grayscale capability for moving-image displays was created.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.2
• /
• pp.7-12
• /
• 2003

The $Bi_{3.3}La_{0.7}O_{12}$(BLT) capacitors with Metal-Ferroelectric-Insulator-Silicon structure were prepared on $SiO_2/Si$ substrates by using sol-gel method. The BLT thin films annealed at $650^{\circ}C$ and $700^{\circ}C$ showed randomly oriented perovskite crystalline structures. The full with at half maximum (FWHM) of the (117) main peak was decreased from $0.65^{\circ}$ to $0.53^{\circ}$ with increasing the annealing temperature from $650^{\circ}C$ to $700^{\circ}C$, indicating the improvement in the crystalline quality of the film. In addition, the grain size and $R_rms$ , values were increased with increasing the annealing temperatures, showing the rough film surface at higher annealing temperatures. From the capacitance-voltage (C-V) measurements, the memory window voltage of the BLT film annealed at $700^{\circ}C$ was found to be about 0.7 V at an applied voltage of 5 V. The leakage current density of the BLT film annealed at $700^{\circ}C$ was about $3.1{\times}10^{-8}A/cm^2$.

• Journal of the Korean Ceramic Society
• /
• v.29 no.11
• /
• pp.870-876
• /
• 1992

Lead lanthanum zirconate titanate (PLZT, 6/65/35) powders, crack-free and dense thin films have been prepared by polymeric sol-gel process. Pyrolysis of the gel, crystallization and optical transmittance behavior of the PLZT thin film onto sapphire substrate have been studied. Esterification occurs during synthesis of PLZT complexation. Crystalline Pb phase was transiently formed near 450$^{\circ}C$. Content of perovskite phase in the films were increased with increasing thickness of film, but the kinetics of formation of perovskite phase in films was slower than that of powders. Transmittance of the films was decreased with increasing the temperature of heat treatment. Ferroelectric hysteresis loop measurements indicated increments of remanent polarization and coercive field for plenty more of perovskite phase.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.35-35
• /
• 2003

Recent progress in the integration of the ferroelectric random access memories (FRAM) has attracted much interest. Strontium bismuth tantalate(SBT) is one of the most attractive materials for use in nonvolatile-memory applications due to low-voltage operations, low leakage current, and its excellent fatigue-free property. High-density FRAMs operated at a low voltage below 1.5V are applicable to mobile devices operated by battery. SBT films thinner than 0.1 #m can be operated at a low voltage, because the coercive voltage (Vc) decreases as the film thickness is reduced. In addition, the thickness of the SBT film will have to be reduced so it can fit between adjacent storage nodes in a pedestal type capacitor in future FRAMs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.377-380
• /
• 2001

The BST thin films to composite (Ba$\sub$x/Sr$\sub$l-x/)TiO$_3$ using sol-gel method were fabricated on Pt/Ti/SiO$_2$/Si substrate. The thin film capacitor to be ferroelectric materials was investigated by structural and electrical properties. BST solution was composited by moi ratio, and then spin-coated (from 3 times to 5 times coating on Pt/SiO$_2$/Si substrate. Thickness of BST ceramics thin films are about 2600∼2800[${\AA}$] in 3 times deposition. The property of leakage current was stable when the applied voltage was 3[V]. Leakage current of 3 times coated BST thin film was 10$\^$-9/∼10$\^$-11/[A] at 0∼3[V].

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.329-332
• /
• 1989

Lead titanate thin films were deposited on titanium substrates by a chemical vapour deposition(CVD) process involving the application of vapour mixtures of Pb, ethyl titanate( Ti($C_2H_5O_4$)), and oxygen. The lead titanate having a stoichiometric composition has a dc conductivity of $3.2{\times}10^{-12}{\Omega}^{-1}{\cdot}cm^{-1}$ at room temperature. The nonsaturating loops observed in present investigation may be attributed to the $TiO_2$ and TiO layers between the conductive substrate and the $PbTiO_3$ ferroelectric film. The ferroelectric properties of the stoichiometric $PbTiO_3$ film included a remanent polarization of 14.1 ${\mu}C/cm^2$ and a coercive field of 20.16 kV/cm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.546-547
• /
• 2002

Ni thin film on the PMN-PT crystal wafer were deposited by using E-beam evaporator technique. Deposited film was patterned by UV-lithography and etching and was in-diffused at 300~600C. Diffusion profile of Ni ions in PMN-PT was measured by secondary ion mass spectroscopy (SIMS).