• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.3
• /
• pp.59-65
• /
• 1991

Failure criteria for asphalt concrete pavements are developed combining the AASHTO design equation and the multi-layered elastic theory. Thickness range including typical layer thicknesses of four-layer Korea highway structures are employed for pavement structure models. Total of 2430 pavement models with different layer thicknesses and moduli are analyzed. Models with crushed stone and asphalt stabilized base courses are equally included in the analysis. Number of load repetition and the maximum tensile strain at the bottom of asphalt layer are computed from the AASHTO design equation with terminal PSI=2.5 and multi-layered elastic computer program, SINELA, respectively. Failure criteria are developed through the regression analysis. From the analysis, failure criteria for the asphalt concrete pavements with 50% and 95% reliability levels are developed. It is found that the failure criterion of 95% reliability level gives similar results with existing fatigue failure criteria whose terminal performance condition is crack development when compared in a graphical form an equation to estimate failure criterion for a specific reliability level is also proposed.

• The Journal of Korean Medicine
• /
• v.36 no.3
• /
• pp.23-34
• /
• 2015

Objectives: This study is aimed at assessing the reliability of a standard instrument of diagnosis and assessment for Spleen Qi deficiency pattern questionnaire (SQDQ) and examining the validity of the SQDQ by comparing the pattern identification scores of different groups. Methods: We conducted a survey of 72 participants (60 patients with chronic dyspepsia and 12 healthy subjects) using self-reported questionnaire. Participants were given written consent and this study was performed under the permission of institutional review board of Kyung-Hee university Korean medicine hospital. Results: The reliability and the validity of the questionnaire were inspected. Internal consistency of the SQDQ was excellent. Construct validity analyzed by exploratory factor analysis produced 4 factors, which were selected from eigenvalues that are greater than 1.0. The factor 1, 2, 3 and 4 showed 'fatigue', 'meal', 'diagnosis' and 'figure' respectively. For most of SQDQs' items, there were significant differences observed between the Spleen Qi and the non-Spleen Qi groups. However, the 'emaciation', 'tongue diagnosis' and 'pulse diagnosis' showed no significant differences. Conclusions: The SQDQ restructured in this study may provide a fundamental questionnaire and a further study is required for a more advanced, standardized and statistically proven questionnaire.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.3
• /
• pp.63-69
• /
• 2019

Soldering technology has been used in electronic industry for a long time. However, due to solder fatigue characteristics, automotive electronics are searching the semi-permanent interconnection technology such as press-fit method. Press fit interconnection is a joining technology that mechanically inserts a press fit metal terminal into a through hole in a board, and induces a strong bonding by closely contacting the inner surface joining of the through hole by plastic deformation of press-fit terminal. In this paper, the bonding properties of press-fit interconnection are investigated with PCB hole size and surface finishes. In order to compare interconnection reliability between the press fit and soldering, the change in resistance of the press-fit and soldering joints was observed during thermal shock test. After thermal cycling, the failure modes are investigated to reveal the degradation mechanism both press-fit and soldering technology.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_3
• /
• pp.1239-1246
• /
• 2022

This paper introduces the effect of grease on the degradation characteristics of bearings used as key components of packaging equipment and automation systems. Bearings parts are installed to fix and support the rotating body of the system, and performance degradation of the bearings has a great effect on the life of the system too. When bearings are used in various devices and systems, the grease is applied to reduce friction and improve fatigue life. Determining the type of lubricant (grease) is important because it has a great influence on the operating environment and lifespan and ensures long lifespan of systems and facilities. However, studies that simultaneously compared and analyzed the change in mechanical degradation characteristics and the comparison of chemical degradation characteristics according to grease types under actual operating conditions are insufficient. In this paper, three types of small harmonic drive, high-load reducer, and low-load reducer grease used in power transmission joint modules are experimentally selected and finally injected into ball bearings with a load (19,500N) to improve bearing durability. Degradation characteristics were tested by attaching to test equipment. At this time, after the durability test under the same load conditions, the mechanical degradation characteristics, that is temperature, vibration according to the three greases types. In addition, the chemical degradation characteristics of the corresponding grease was compared to present the results of mutual correlation analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.648-655
• /
• 2020

The firing pin of modern automatic rifles detonates the primer of loaded ammunition via a hammer. During this process, the firing pin receives an impact load and repetitive force throughout the life of the rifle. An endurance test of a rifle showed that the firing pin breaks prematurely at 96.26% of life. Accordingly, a case study was conducted through cause analysis and a reconstruction test. Optical microscopy and scanning electron microscopy of the broken surface of the firing pin showed that a crack began in the circumferential direction of the surface, resulting in a fatigue crack to the core after repeated impact. Crack growth and fatigue destruction occurred at the end due to the repetitive impact and was estimated using a notch. For verification, a sample that produced a 0.03mm circumferential notch was broken at 64.25% of life in the reconstruction test. A test of breakage according to the notch types showed that a 0.3mm and a 0.5mm one-side notch were broken at 66.53% and 50.76%, respectively, and a 0.03mm six-point notch was broken at 85.65%. The endurance life of a sample firing pin with a rough surface and tool mark was examined, but an approximately 381 ㎛ internal crack formed. Through this study, failure for each notch type was considered. These results show that quality control of the notch and surface roughness is essential for ensuring the reliability of a component subjected to repeated impact.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.939-950
• /
• 2011

In this study, the load test of rubber tire bogie for monorail type LRT. Bogie for rolling stock in safety operation of the vehicle as an essential core unit before applying to the vehicle safety and reliability should be tested sufficiently. Rubber tire monorail type bogie compared to the traditional bogie wheel lots of formats, the complexity of the load acting static load test, the bogie of the vehicle operation conditions by structural analysis by considering the loading conditions was evaluated by calculating. Test methods and evaluation criteria based on urban rail vehicle performance testing by applying the test were welded parts and materials for the results leading to material fatigue endurance test by applying the result of evaluating the structure has been identified as safe.

• Advances in aircraft and spacecraft science
• /
• v.5 no.2
• /
• pp.239-249
• /
• 2018

Physical tests are performed at various stages of the development cycle of a product, from prototype validation to product qualification. Although costly, there are growing demands for qualification tests like endurance vibration testing to be more representative of the real world. At the same time there are growing demands to assess the durability of these items based on FEA simulation. In this paper, we will explain how to set up a CAE-based test and how to correlate the results with some physical measurements. Specific assumptions will be explained and some advantages of using virtual tests will be highlighted such as the reduction of the number of prototypes needed, investigations on failures, evaluation of the level of reliability via sensitivity analysis, evaluation of the margins are at the end of a successful test. This presentation will therefore focus on explaining and showing how virtual tests can enrich the exploitation of physical tests.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.5
• /
• pp.512-521
• /
• 1997

This paper deals with an evaluation of the residual stress due to shot peening induced in a car¬burized gear tooth and its application to the fatigue crack propagation problem. The residual stress is estimated based on the assumption that the main cause of residual stress is the volume difference between the case and core due to martensitic transformation in cooling, and the influ¬ence of both the reduction of retained austenite and the strain in the surface layer induced by shot peening are considered. The reliability of the method is examined by comparison with stresses measured by the X-ray diffraction method. The stresses intensity factors are computed by the influence function method and the reduction of the factor due to the residual stress is demonstrat¬ed and discussed based on the fracture mechanics.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.608-613
• /
• 2002

In this paper we developed the MPC sensor for steering control and steering control of the AGVDS(Autonomous Guided Vehicle Driving System) for Durability test. Among durability tests, the accelerated durability test has been widely used to evaluate the durability of vehicle structure and chassis parts in a short period of time on the designed road that has severe surface conditions. However it increased the drivers fatigue mainly caused by the severe driving conditions. The driver's difficulty to maintain the constant speed and control the steering wheel reduces the reliability of test results. In addition to the general detecting sensor for steering control was restricted by surrounding condition. So we need to develop steering control sensor was robust in the bad driving condition. In this paper we developed steering control sensor using magnetic induction which is robust in the bad driving condition and implemented the AGVDS.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.2
• /
• pp.44-52
• /
• 1991

The crankshaft system of engine is a complex vibratory object and its vibration modes are consisted of torsional, axial and their coupled vibration. Among them, the torsional vibration causes engine noise as well as serious fatigue faillures of crankshaft. If the troules of noises and crankshaft strength are forecasted by torsional vibration calculation in the design atage of crankshaft, the torsional damper is adopted as the final countermeasure. In this paper, some computer program to calculate crankshaft torsional vibration of engine are developed and with developed programs, an efficient rubber-viscous damper for automobile and with developed programs, an efficient rubber-viscous damper for automobile engine is designed and manufactured, and then it is fitted on the actual automobile engine to confirm its calculated efficiency. By comparing the measured result (with damper and without damper) with the calculated one, the reliability of developed computer programs and the performances of manufactured damper are confirmed.