• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.265-268
• /
• 2007

플렉서블 태양전지용 연성기판재에는 플라스틱재와 금속재가 있다. 기존의 연성기판인 플라스틱의 경우 열과, 내구성, 화학약품에 약하다는 단점이 있으며, 금속기판은 높은 생산원가, 박판화의 어려움 등의 문제를 안고 있다. 상업적으로 응용되거나 연구에 활용되는 플렉서블 기판재의 단점을 보완할 수 있는 가능성을 밝혀보기 위해 전주성형법으로 합금 금속 포일을 제조하여 상용 금속 기판재의 열팽창 거동과 비교해 보았다. 본 연구에서는 플렉서블 태양전지용으로 적용되거나 연구되고 있는 금속 기판 재료인 두께 50 ${\mu}m$인 Ti, Mo, Al 포일을 선택하여 열팽창거동을 조사하였고 이를 전주성형법으로 제조한 두께 10 ${\mu}m$인 Fe-40Ni, Fe-45Ni, Fe-52Ni 합금포일의 열팽창 거동과 비교 분석하였다. 금속 및 합금 포일의 열팽창 거동은 TMA 장비를 사용하여 조사하였다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.233-234
• /
• 2010

Using an expansion admixture can reduce an initial shrinkage crack and improve a prestress. Therefore, this paper presents the results of a study performed to evaluate this deformation and obtain a better understanding of the behavior of SHCC using an expansion admixture. To evaluate a performance of SHCC using an expansion admixture was tested a drying shrinkage, compressive strength, flexural strength, and tensile strength.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.12
• /
• pp.1701-1709
• /
• 1997

The diagnostic used to observe the early flame development was a fiber optic spark plug, which enabled measurement of the flame front arrival times on a cycle-to-cycle basis. The data obtained with this fiber optic spark plug were analyzed to obtain two parameters to describe the behavior of the flame kernel : an expansion speed and a convection velocity. In addition, synchronized cylinder pressure data were taken to compare with the fiber optic spark plug data on a cyclic basis. Heat release analysis was performed on the cylinder pressure data to obtain the mass burning profile of the charge for each cycle. There was a significant correlation observed in the initial flame duration and the kernel expansion speed with dwell angle.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.11a
• /
• pp.79-83
• /
• 2005

In the reinforced concrete structure, Even if speak that water leakage occurrence is no problem to material, there is a lot of reasons construction factor, material damage by behavior structure, properties of matter change by years and water leakage part by environment condition. so, waterproofing technological consideration should be gone ahead. In this research, we will study about stick performance, concrete surface adhesive, damage and blow. we will check all things and test it. The stick expansion type complex of flexible material passed on result of standard. It is conducive to concrete of durability by waterproofing layer performance demobilitation technology on the water leakage structure for solution of problem and repair

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1997.10a
• /
• pp.95-102
• /
• 1997

Jointless bridge is a new construction method applicable to bridge of short length. In the jointless bridge expansion of superstructure due to thermal effect was absorbed in the flexible pile-type abutment in stead of expansion joint in the conventional bridges. By removing expansion joint, it retards deterioration and extends life time of bridge. In this paper, jointless bridge of steel box girder type was studied through finite element analysis. Stress variations of superstructure and pile due to thermal effect was studied for the two span continuous integral bridge of 80m length and the results of analysis was presented.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1346-1353
• /
• 2009

In this study, a numerical study was carried out to simulate the expansion of ground borehole by pulse discharge technology using finite element analysis. Considering the mortar in the borehole as an acoustic medium and the surrounding soil as an elasto-plastic material, the strong shock wave developed by the pulse discharge was modeled using the underwater explosion model. The ground expansion was simulated based on a coupled acoustic-structural analysis with varying properties of mortar and soil, and the behavior between acoustic-structural interface.

• Structural Engineering and Mechanics
• /
• v.36 no.4
• /
• pp.447-461
• /
• 2010

Fiber reinforced polymer (FRP) bars have been widely used as reinforcement for concrete structures. However, under elevated temperatures, the difference between the transverse coefficients of thermal expansion of FRP rebars and concrete may cause the splitting cracks of the concrete cover. As a result, the bonding of FRP-reinforced concrete may not sustain its function to transfer load between the FRP rebar and the surrounding concrete. The current study investigates the cracking resistance of FRP reinforced concrete against the thermal expansion based on a mechanical model that accounts for the tensile softening behavior of concrete. To evaluate the efficacy of the proposed model, the critical temperature increments at which the splitting failure of the concrete cover occurs and the internal crack radii estimated are compared with the results obtained from the previous studies. Simplified equations for estimating the critical temperature increments and the minimum concrete cover required to prevent concrete splitting failure for a designated temperature increment are also derived for design purpose.

• Advances in concrete construction
• /
• v.3 no.1
• /
• pp.39-54
• /
• 2015

Relative humidity and strains within a massive concrete cylinder (${\varphi}450mm{\times}900mm$) in the drying and the re-saturating process were measured for elucidating the process of ASR surface cracking in concrete. The expansion behavior of mortars in dry atmospheres with various R.H. values and the resaturating process was revealed. Non- or less-expansive layers were formed in near-surface regions in the concrete cylinder in the drying process, but ASR expansions actively progressed in inner portions. After resaturating, R.H. values of near-surface regions rapidly increased with time, but expansions in the regions were found to be very small. However, in the middle portions, of which R.H. values were kept 80% ~ 90% R.H. in the drying process, expansion actively progressed, resulting in further development of surface cracks in the re-saturating process.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.2
• /
• pp.46-51
• /
• 2002

Cold expansion of fastener holes is a mechanical process widely used in the aerospace industry. This treatment leads to an improvement of fatigue behavior due to the developed compressive residual stresses on the hole surface. The residual stress profile depends on the parameters of cold expansion, which are expanding rate, inserting direction of mandrel, material properties dtc. Despite its importance to aerospace industiries, little attention has been devoted to the accurate modeling of the process. In this paper, three-dimensional finite element simulations have been conducted for the cold expansion in an aluminium plate in order to predict the magnitude and distribution of the residual stress. To prove the results of FE analysis, the residual strain was measured by strain gage in cold expansion test. Maximum compressive residual stress could be increase about 7 percentage using the 2-step cold expansion method.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.3
• /
• pp.89-93
• /
• 2020

Complex warpage behavior of the electronic packages causes internal stress so many kinds of mechanical failure occur such as delamination or crack. Efforts to predict the warpage behavior accurately in order to prevent the decrease in yield have been approached from various aspects. For warpage prediction, silicon is generally treated as a homogeneous material, therefore it is described as showing no warpage behavior due to thermal loading. However, it was reported that warpage is actually caused by residual stress accumulated during grinding and polishing in order to make silicon wafer thinner, which make silicon wafer inhomogeneous through thickness direction. In this paper, warpage behavior of the single-side polished wafer at solder reflow temperature, the highest temperature in packaging processes, was measured using 3D digital image correlation (DIC) method. Mechanism was verified by measuring coefficient of thermal expansion (CTE) of both mirror-polished surface and rough surface.