• 한국세라믹학회지
• /
• 제45권10호
• /
• pp.573-578
• /
• 2008

In the preparation of hydroxyapatite(HAp)/gelatin(GEL) nanocomposite, GEL matrix was modified by the introduction of chondroitin sulfate(ChS) to obtain a strongly organized composite body. The formation reaction of the HAp/GEL-ChS nanocomposite was then investigated via XRD, DT/TGA, FT-IR, TEM and SEM. The organic-inorganic interaction between HAp nanocrystallites and GEL molecules was confirmed from DT/TGA and FT-IR. According to the DT/TGA results, the exothermal temperature zone between 300 and $550^{\circ}C$ showed an additional peak temperature that indicated the decomposition of the combined organics of the GEL and ChS. From the FT-IR analysis, calcium phosphate(Ca-P) was covalently bound with the GEL macromolecules modified by ChS. From TEM and ED, the matrix of the GEL-ChS molecules was mineralized by HAp nanocrystallites and the dense dried nanocomposite body was confirmed from SEM micrographs.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.547-550
• /
• 2008

A solid rocket motor has quite complex physical condition such exothermal chemical reaction in subsonic area and supersonic ex pansion in a converging-diverging nozzle. To introduce a simulation tool for compressible flow in supersonic range as well as incompressible chemical reaction zone in a whole rocket nozzle is a essential demand. Since the flow vary subsonic to super sonic, the convergence in computation becomes very low and unstable in a whole domain of rocket motor. This paper reports the 2-D Axisymmetric and simple 3-D solid propellant combustion and flow of gases in rocket motor by using a precondi tioning, shear stress turbulence modeling, AUSM(p). To simulate the simplified combustion process, Double base solid propellant is used to calculate reaction of solid propellant.

• Journal of Magnetics
• /
• 제11권1호
• /
• pp.36-42
• /
• 2006

In this report, we demonstrate a comprehensive analysis of the effects of Au addition on the microstructure and magnetic properties of $Fe_{73.5}Si_{13.5}B_{9}Nb_{3}Au_1$ Finemet-type alloy. It was found that the as-quenched alloys were the amorphous state and turned into nanocrystalline state under heat treatments. The DSC analysis indicates that the sharply exothermal peak corresponding to the crystallization of the $\alpha-Fe(Si)$ was observed at $547-579^{\circ}C$ depending on the heating rates, which is little higher than that of original Finemet (542-$570{^{\circ}C}$, respectively). Besides, the thermomagnetic result confirmed that the full substitution of Cu by Au with the single phase structure in the M(T) curve along cooling cycle. Ultrasoft magnetic properties of the nanocrystallized samples were significantly enhanced by the proper annealing such as the increase of permeability and the decrease of the coercivity. The optimum annealing condition was found at the annealing temperature of $540^{\circ}C$ and the increase of the annealing time up to 90 min.

• 한국분말재료학회지
• /
• 제23권3호
• /
• pp.202-206
• /
• 2016

A Ni-Ti-B alloy powder prepared by mechanical alloying (MA) of individual Ni, Ti, and B components is examined with the aim of elucidating the phase transitions and crystallization during heat treatment. Ti and B atoms penetrating into the Ni lattice result in a Ni (Ti, B) solid solution and an amorphous phase. Differential thermal analysis (DTA) reveals peaks related to the decomposition of the metastable Ni (Ti, B) solid solution and the separation of equilibrium $Ni_3Ti$, $TiB_2$, and ${\tau}-Ni_20Ti_3B_6$ phases. The exothermal effects in the DTA curves move to lower temperatures with increasing milling time. The formation of a $TiB_2$ phase by annealing indicates that the mechanochemical reaction of the Ni-Ti-B alloy does not comply with the alloy composition in the ternary phase diagram, and Ti-B bonds are found to be more preferable than Ni-B bonds.

• Elastomers and Composites
• /
• 제18권4호
• /
• pp.140-147
• /
• 1983

The purpose of this dissertation is to increase oxidation resistance for Polybutadiene & Polyisoprene, and to investigate the energetics of inhibited oxidation of Polybutadiene & Polyisoprene stabilized with various types of antioxidants using DSC. The results of the study are as fellows: 1. In the DSC SCREEN for the onset temperature of oxidation, Polybutadiene was faster than Polyisoprene for the samples containing no antioxidant in air. 2. In the DSC evaluation for Polybutadiene, Recipe BG-4 with 2.0phr compounds of antioxidant was the best effective, and Recipe BS-4 with 2.0phr compounds of antioxidant was the worst effective, and the degrees of effect of antioxidant were exhibited in the ranking of G-1, D, BHT, and SP, roughly. 3. In the DSC evaluation for the Polyisoprene, Recipe IG-4 with 2.0phr compounds of antioxidant was the best effective, and Recipe ID-4 with 2.0phr compounds of antioxidant was the worst effective, and the degrees of effect of antioxidant were exhibited in the ranking of G-1, SP, BHT, and D roughly. 4. In the study on enthalpy which depends on exothermal reaction, the enthalpy of Polyisoprene was gloater than that of Polybutadiene. However, the problem was not solved completely, and it needs further studies.

• International Journal of Concrete Structures and Materials
• /
• 제9권1호
• /
• pp.55-60
• /
• 2015

In this study, influence of different stone powders (SP), including limestone powders (LP), quartzite powders (QP), and granitic powders (GP), on the hydration behaviors of portland cement, for example, setting time, hydration heat, and hydration products, were discussed. The initial and the final setting time both shorten when the content of LP is 5 %, however, they are slightly delayed by the other two SPs. The LP has no obvious influence on the arrival time of the first peak in the exothermal curves, and it makes the peak value decrease; the other two SPs postpone the appearance of the first peak, and they also make the peak value decrease. For the second peak, LP shifts the peak position to the left, QP has no effect on this peak position, and GP makes the appearance of this peak delayed by 143 min. Similarly, three kinds of SPs have different influence on the hydration products of portland cement. The LP precipitates the formation of hydrated calcium carbo aluminate, the QP the formation of hydrated garnet, and the GP makes the amount of Tobermorite increase.

• Korean Chemical Engineering Research
• /
• 제58권4호
• /
• pp.624-634
• /
• 2020

The ability of natural and modified clay to adsorb phenol was studied. The clay samples were analyzed by different technical instruments, such as X-ray fluorescence (XRF), X-ray diffraction (XRD) and FT-IR spectroscopy. Surface area, pore volume and average pore diameter were also determined using B.E.T method. Up to 73 and 99% of phenol was successfully adsorbed by natural and activated clay, respectively, from the aqueous solution. The experiments carried out show that the time required to reach the equilibrium of phenol adsorption on all the samples is very close to 60 min. The amount of phenol adsorbed shows a declining trend with higher pH as well as with lower pH, with most extreme elimination of phenol at pH 4. The adsorption of phenol increases proportionally with the initial phenol concentration. The maximum adsorption capacity at 25 ℃ and pH 4 was 29.661 mg/g for modified clay (NaMt). However, the effect of temperature on phenol adsorption was not significant. The simple modification causes the formation of smaller pores in the solid particles, resulting in a higher surface area of NaMt. The equilibrium results in aqueous systems were well fitted by the Freundlich isotherm equation (R² > 0.98). Kinetic studies showed that the adsorption process is best described by the pseudo-second-order kinetics (R² > 0.99). The adsorption of phenol on natural and modified clay was spontaneous and exothermal.

• 공업화학
• /
• 제29권6호
• /
• pp.703-709
• /
• 2018

마이크로웨이브에 감응하는 주요물질인 Li와 Zn계 전구체를 다양한 조건별로 혼합 및 열처리하여 유전발열소재(dielectric heating materials)를 제조하였다. 제조된 발열소재의 표면 형태 등의 변화를 SEM 분석으로 확인하였으며 기공구조, 열처리 단계 그리고 표면에 형성되어 있는 $Li_5Fe_5O_8$ 물질이 발열성능에 주요한 영향인자임을 확인하였다. 또한 슬러지 건조 장치에 발열소재가 적용되었을 경우와 그렇지 않은 경우 25%의 함수율을 갖는 슬러지가 각각 6.34%, 15.22%로 건조되어 슬러지 수분 제거효율이 58.34% 상승하였음을 확인하였다. 이에 따라 발열소재가 마이크로웨이브 건조 공정의 성능 및 효율에 직접적인 영향을 미칠 수 있음을 확인하였다.

• 대한치과보철학회지
• /
• 제33권2호
• /
• pp.210-230
• /
• 1995

To compare the wear resistance of four kinds of commercial acrylic resin teeth [SR-Orthosit PosterioresR(Ivoclar Co., Liechtenstein), Endura PosteriorR(Shofu Inc. Japan), trubyte IPN teethR(Dentsply International Inc., York,), Trubyte BiotoneR(dentsply Inermational Inc. Brazil) by means of the toothbrush abrasion method, the artificial resin teeth were embedded in epoxy resin with the occlusal surfaces aligned in one plane for a total of 40 blocks. There after, each lock was mounted in the arm of the toothbrush abrasion machine(K 236, Japan). Wear measurements were made on the three preconditioned states. Those were as follows : no treatment specimens, thermocycled specimens, and thermocycled specimens which were immeresed applied load of 400g during the buring the brushing cycle. At the end of the 30,000-stroke cycle, each specimen was removed, and weighed. The microhardness of four kinds of commercial resin teeth were determined by means of microhardness tester. Microhardness tests were performed on te no treatment specimens, thermocycled specimens, and thermocycled specimens with immersion in the denture cleansing solution. Finally, the comparison of thermal properties were perfomed using differential scanning calorimeter(DSC-1500). The following results were obtained : 1. In the case of no treatment teeth, the wear amount of endura Posterior(EN) was the greatest among the others(p<0.01), and the wear amount of three kinds of artificial resin teeth was increased in the order of Trubyte IPN teeth(IN), Trubyte Biotone(BN), SR-Orthosit Posteriores(SN) but there was no statistic significance(p>0.01). 2. The wear amount of Trubyte IPN teeth(IT) and Trubyte Biotone(BT), was increased due to thermocycling effect, but that of Endura Posteriores(ET) was decreased conversely(p<0.01). 3. Except for the SR-Orthosit Posteriores(STC), the wear amount of three kinds of artificial resing teeth(that is, ETC, ITC, BTC) was increased due to denture cleansing solution$(Cledent^R)$, but there was no statistic significance(p>0.01). But the wear amount of the SR-Orthosit Posteriores(STC) was the greatest among the others(p<0.01). 4. The wear amount of toothbrush was the greatest in case of contact with occlusal surface of SROrthosit Posteriores resin teeth(p<0.01). 5. the microhardness values(KHN) of the SR-Orthosit Posteriores was the highest among the experimental artificial resin teeth(p<0.01). 6. There was no relationship between microhardness valuse(KHN) and wear amount of four kinds of experimental artificial resin teeth(p<0.01). 7. The differential canning calorimetric property of four kinds of artificial resin teeth did not show endothermal or exothermal peak in the range of $100^{\circ}C$

• Applied Biological Chemistry
• /
• 제20권1호
• /
• pp.117-122
• /
• 1977

담배에 질산염을 청가하면 질소화합물이 증가되므로 질산염의 대체물(代替物)을 개발(開發)하기위한 실험을 한 결과 다음과 같은 결론을 얻었다. 여러가지 첨가제 중에서 $0.6{\sim}1%$의 시트르산나트륨을 첨가하는 것이 연소성 및 Tar, Nicotine의 감소효과(減少效果)가 가장 양호했다. 특히 조연제첨가(助燃濟添加)에 따른 연소성(燃燒性)과 유해성분감소효과(有害成分減少效果) 및 열특성(熱特性)에 대(對)한 다음과 같은 결과를 얻었다. 1) 연소성이 좋으면 Tar, Nicotine, Bonzpyrene Phenols, NO, $NO_2E, 등의 유해성분이 감소됐다. 2) 단엽에 첨가(添加)된 질산염과 시트르산염의 시차열분석효과(示差熱分析效果)는 시트르산염 첨가시(時) L치(値)가 가장 적고 H치(値)가 가장 컸다. 3) 순수한 질산염과 시트르산염의 시차열분석(示差熱分析)에서 전자는 발열반응(發熱反應)이 없는데 후자는 발열반응(發熱反應)이 있었다. 4) $0.6{\sim}1%$의 시트르산나트륨 첨가시(時)에 Zone A에서는 Tar생성량이 많았고 Zone B에서는 Tar 생성량이 가장 적었다. 또한 이들 담배의 연기에서는 Tar, Nicotine, Phenols, Nitrogen oxides, Benzpyrene의 함량(含量)이 적었으며 연소성이 향상되었다.