• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.413-421
• /
• 1990

Acoustic emission signals due to leak from circular holes of 0.4, 1, 2 and 4mm diameter and rectangular slits of different geometry having the same cross section as 4mm diameter hole was studied both analytically and experimentally. Acoustic emission signals from a wide-band type transducer were transformed to digital signals through a digital oscilloscope, and $V_{rms}$ and frequency spectrum were obtained by processing digital signals. Relationships between acoustic parameters and fluid mechanical parameters were derived analytically. A quadrapole aerodynamic model was applied in the analysis of leak from the circular holes and $V_{rms}$ was found to be proportional to the root square of leak rate through the circular hole. A modified model based on dipole source mechanism and laminar equivalent diameter was applied in the analysis of leak signals from the rectangular slits. In the case of constant pressure, $V_{rms}$ increased as the laminar equivalent diameter of slit decreased. In the case of constant laminar equivalent diameter, however the result was similar to that for leak from the circular hole. The frequency spectra of leak signals shows the same frequency characteristics irrespective of the pressure difference.rence.

• 센서학회지
• /
• 제10권2호
• /
• pp.142-147
• /
• 2001

인터디지털 표면음파 변환기의 교차장 모델에 기초한 전송선 등가회로를 사용하여 SPICE에 의한 SAW 필터의 효율적인 시뮬레이션 기법을 제안하였다. 표면음파의 전파를 전송선으로 모델하므로 인터디지털 변환기의 등가회로에서는 주파수 의존 회로소자가 필요하지 않게 된다. 그래서 주파수 의존 회로소자에 대한 등가회로를 근사적으로 구하지 않아도 되고, 필터의 등가회로에 작은 수의회로소자를 사용하므로 시뮬레이션 시간도 많이 단축된다. 삽입손실, 입력 어드미턴스, 통과대역 리플, 그리고 고조파 주파수 응답과 같은 SAW 필터 특성에 대한 시뮬레이션을 통하여 제안된 기법의 유용성을 보였다.

• 한국산학기술학회논문지
• /
• 제10권6호
• /
• pp.1180-1185
• /
• 2009

본 논문에서는 T-접합선로의 집중소자 등가회로를 고려한 저역통과 여파기를 제안하였다. 일반적인 저역통과 여파기 설계 시 발생하는 T-접합선로의 특성에 따른 주파수 변이 특성을 해결하기 위해 T-접합선로 등가회로의 소자 값을 구하는 수식을 유도 하였다. 또한, 전자장 시뮬레이터(HFSS)를 이용하여 T-접합선로를 디임베딩하였다. 이로써 선로의 임피던스 허수값들이 일치되게 하여 T-접합선로 등가회로에서 집중소자의 정확한 값을 구하였다. 그리고 이 값들을 이용하여 저역통과 여파기를 설계한 결과, 집중소자 여파기의 주파수 특성과 분포소자 여파기의 주파수 특성이 매우 잘 일치함을 확인할 수 있었다.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.36-40
• /
• 2008

This study is analyzed by the simulation of automotive steering system. The maximum equivalent stress of $2.2418{\times}109Pa$ and the maximum total displacement of 0.014929m are shown at the universal joint and its lower part respectively. As the minimum cycle of 34.047 is shown at the universal joint in case of fatigue analysis, it is possible to have greatest damage at this part. In case of natural frequency analysis at vibration, its frequency of 47 to 59Hz is occurred generally. The maximum total displacement of 0.5m is shown at handle on the natural frequency of 57 to 58Hz. And the displacement over 2m is shown at the lower part of universal joint on the natural frequency of 58 to 59Hz. As the basis of the simulation analysis of steering system, passenger's comfort of car body can be improved in the design of practical part and the design effect necessary to safe driving can be promoted.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.22-30
• /
• 2011

This study analyzes harmonic vibration with natural frequency according to the configuration of damper clutch. In the case of double spring, equivalent stress at same direction of the revolution at inner and outer coil spring is over 30% as compared with at its opposite direction. Natural frequency or harmonic response with maximum deformation in case of the less coil pitch is below 3Hz as compared with in case of the more coil pitch. As the coil pitch of damper spring as the case 2 or 4 becomes smaller, its mass and deformation can be large. In these cases, spring constant and natural frequency become smaller. In the case 5 or 6 of double spring at natural vibration or harmonic response, the frequency becomes over 300Hz. As the result of this study is applied by the design of damper spring, the damage at its connected part is prevented and the durability can be predicted.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.61-63
• /
• 1999

This paper presents an efficient method for analysis of magnetodynamic system using frequency-dependent parameters. In equivalent electric circuit of linear magnetodynamic system, parameters of inductance and resistance are not constant since they vary with its driving frequency. Once frequency-dependent parameters of equivalent electric circuit for a given system are extracted, they can be used to analyze various characteristics of system. We use the Fourier transform, the high-order sensitivity method and Taylor series in order to efficiently extract the frequency-dependent parameters of magnetodynamic system. The proposed algorithm is applied to an induction heating system to validate its numerical efficiency.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권1호
• /
• pp.24-29
• /
• 1996

A composite piezoelectric ceramic transducer is fabricated with three piezoelectric ceramic disk vibrators and two sheets of thin insulator. Its equivalent circuit is derived from the Mason's model of a thickness-driven piezoelectric vibrator. When the electric input near its fundamental resonance frequency is applied to the center vibrator and the output voltages across the left and the right vibrators are connected in series to the resistor loads, the load characteristics at resonance frequencies under the various resistor loads and the frequency characteristics near the resonance frequency without load are investigated. Furthermore, symbolic expressions for input impedances, voltage ratios, resonance frequencies, and bandwidths are derived. The data calculated from those symbolic expressions are agreed well with the measurement data.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.402-407
• /
• 1997

For cylindrical shells, the closed-form solutions are limited only to the cases with special boundary and/or loading conditions. Though the finite element method is certainly a powerful solution approach for the general structural dynamics problems, it is known to provide reliable solutions only in the low frequency region due to the inherent high sensitivities of structural and numerical modeling errors. Instead, the spectral element method has been proved to provide extremely accurate dynamic responses even in the high frequency region. Since the wave characteristics of a cylindrical shell becomes identical to that of a flat plate as the frequency increases, an equivalent plate model (EPM) representing the high-frequency dynamic characteristics of a cylindrical shell is introduced herein. The EPM-based spectral element analysis solutions are compared with the known analytical solutions for the corresponding cylindrical shell to confirm the validity of the present modeling approach.

• Journal of Power Electronics
• /
• 제3권2호
• /
• pp.139-144
• /
• 2003

In this paper, 11 and 13 layered step-down piezoelectric transformers were fabricated and their electrical characteristics have been analyzed for AC-adapter. When the voltage is applied to the driving piezoelectric vibrator polarized in the longitudinal direction, the output voltage is generated at the generating piezoelectric vibrator polarized in the thickness direction due to the piezoelectric effects. From the piezoelectric direct and converse effects, symbolic expressions between the electric inputs and outputs of the step-down piezoelectric transformer are derived with an equivalent circuit model. With those expressions, load and frequency characteristics are discussed through the simulations. Output voltage and current from a 11-layered and a 13-layered piezoelectric transformers were measured under the different load and frequency conditions. First we measured resonant frequency from impedance curve and got equivalent impedance value of the piezoelectric transformer from admittance plot. It was shown from experiments that output voltage increase s and resonant frequency changes according to the various resistor loads. Output current decreases inversely proportional to the change of loads. Moreover, the measured output voltage and current are well matched with the simulated results obtained from the proposed equivalent circuit model. Furthermore, a new step-down piezoelectric transformer has been suggested to Increase the output power based on a simulation result having a driving piezoelectric vibrator polarized thickness direction.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 A
• /
• pp.143-144
• /
• 2006

The recent power systems are very complex and to model them completely is impractical for analysis of electromagnetic transient Therefore areas outside the immediate area of interest must be represented by some form of Frequency Dependent Network Equivalent (FDNE). In this paper a method for developing Frequency Dependent Network Equivalent (FDNE) using S-domain rational Function Fitting is presented and demonstrated. The FDNE is generated by Linearized Least Squares Fitting(LSF) of the frequency response of a S-domain formulation. This Three-port FDNE have been applied to the test AC power system. The electromagnetic transient package PSCAD/EMTDC is used to assess the transient response of the Three-port FDNE developed under different condition. The study results have indicated the robustness and accuracy of Three-port FDNE for analisys of electromagnetic transient and harmonic assessment.