• 한국정보통신학회논문지
• /
• 제18권12호
• /
• pp.2933-2938
• /
• 2014

전류컨베이어 회로를 이용한 주파수 고정 루프 회로를 $0.35{\mu}m$ CMOS 공정으로 설계하였다. 공급전압은 3volts를 사용하였다. 설계된 회로는 분주기, 주파수-전압 변환기, 전압 감산기 및 발진기로 구성하였으며, 각 회로 블록을 대칭적으로 배치하여 공정 변화에 따른 신뢰성 특성을 향상시켰다. HPICE 시뮬레이션 결과 MOS 트랜지스터의 채널길이, 채널 폭, 저항 및 커패시터의 크기가 ${\pm}5%$ 변화할 때 출력주파수의 변화율은 ${\pm}1%$ 내외였다.

• 융합보안논문지
• /
• 제20권1호
• /
• pp.69-75
• /
• 2020

지휘통제체계는 인간의 두뇌와 신경 조직처럼 정보·감시·정찰(ISR)에서 정밀타격체계(PGR)를 연결하는 링커이며 전투력의 중심이다. 미래 한국군의 지휘통제체계 구축시 기술적 문제뿐만 아니라 제도적 문제를 함께 고려해야 한다. 미국 국방부는 지휘 통제체계 개발에 앞서 보안 정책을 수립하고 이를 구체화하여 아키텍처 문서로 정리하며, 이를 토대로 보안 정책의 일관성과 지속을 유지한다. 본 논문에서는 미군의 지휘통제체계 구축시 적용하는 보안 아키텍처를 살펴보고 현행 한국군의 보안 관련 정책(규정)을 분석하여 미래 지휘통제체계 구축 시 보안 요구사항을 식별한다. 식별된 보안 요구사항을 그룹핑하여 현행 보안 관련 규정의 분야별 개선사항을 도출하여 제시하고자 한다.

• Computers and Concrete
• /
• 제3권2_3호
• /
• pp.79-90
• /
• 2006

This paper describes the results of an investigation into high mass-low velocity impact behaviour of reinforced concrete beams. Tests have been conducted on fifteen 2.7 m or 1.5 m span beams under drop-weight loads. A high-speed video camera has been used at rates of up to 4,500 frames per second in order to record the crack formation, propagation, particle spallation and scabbing. In some tests the strain in the reinforcement has been recorded using "Durham" strain gauged bars, a technique developed by Scott and Marchand (2000) in which the strain gauges are embedded in the bars, so that the strains in the reinforcement can be recorded without affecting the bond between the concrete and the reinforcement. The impact force acting on the beams has been measured using a load cell placed within the impactor. A high-speed data logging system has been used to record the impact load, strains, accelerations, etc., so that time histories can be obtained. This research has led to the development of computational techniques based on combined continuum/discontinuum methods (finite/discrete element methods) to permit the simulation of impact loaded reinforced concrete beams. The implementation has been within the software package ELFEN (2004). Beams, similar to those tested, have been analysed using ELFEN a good agreement has been obtained for both the load-time histories and the crack patterns.

• Geomechanics and Engineering
• /
• 제10권5호
• /
• pp.577-598
• /
• 2016

This paper presents a numerical study of pile force distribution in a pile group foundation subjected to vertical load and large moment. The physical modeling of a pile foundation for a wind turbine is analyzed using 3D finite element software, PLAXIS 3D. The soil profile consists of several clay layers, which are modeled as Mohr-Coulomb material in an undrained condition. The piles in the pile group foundation are modeled as special elements called embedded pile elements. To model the problem of a pile group foundation, a small gap is created between the pile cap and underlying soil. The pile cap is modeled as a rigid plate element connected to each pile by a hinge. As a result, applied vertical load and large moment are transferred only to piles without any load sharing to underlying soil. Results of the study focus on pile load distribution for the square shape of a pile group foundation. Mathematical expression is proposed to describe pile force distribution for the cases of vertical load and large moment and purely vertical load.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2346-2351
• /
• 2008

This study deals with heat pipes inserted into the metal hydride(MH) reactor to increase the effective thermal conductivity of the system and thus to enhance the thermal control characteristics. A numerical analysis was conducted to predict the effect of inserted heat pipes on the heat transfer characteristics of MH, which inherently has extremely low thermal conductivity. The numerical model was a cylindrical container of O.D. 76.3 mm and length 1 m, which is partially filled with about 60% of MH material. The heat pipe was made of copper-water combination, which is suitable for operation temperature range between $10^{\circ}C$ and $80^{\circ}C$. Both inner -and outer- heat pipes were considered in the model. Less than two hours of transient time is of concern when decreasing or increasing the temperature for absorption and discharge of hydrogen gas. FLUENT, a commercial software, was employed to predict the transient as well as steady-state temperature distribution of the MH reactor system. The numerical results were compared and analyzed from the view point of temperature uniformity and transient time up to the specified maximum or minimum temperatures.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2010년도 학술발표회
• /
• pp.283-287
• /
• 2010

Stochastic simulation of hydrologic data has been widely developed for several decades. However, despite the several advances made in literature still a number of limitations and problems remain. In the current study, some stochastic simulation approaches tackling some of the existing problems are discussed. The presented models are based on nonparametric techniques such as block bootstrapping, and K-nearest neighbor resampling (KNNR), and kernel density estimate (KDE). Three different types of the presented stochastic simulation models are (1) Pilot Gamma Kernel estimate with KNNR (a single site case) and (2) Enhanced Nonparametric Disaggregation with Genetic Algorithm (a disaggregation case). We applied these models to one of the most challenging and critical river basins in USA, the Colorado River. These models are embedded into the hydrological software package, Pros and cons of the models compared with existing models are presented through basic statistics and drought and storage-related statistics.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제52권8호
• /
• pp.443-451
• /
• 2003

Many attempts have been made for the health and lives of patients at a remote site. but little attention has been given to emergency system using wireless or other intelligent networks. In this paper, shown is a remote emergency system which can be used in an ambulance. It possibly gives a great help to the patients who may lose their lives, in other words, gives pre-hospital cure to them being sent to the hospital. Doctors or specialists are able to give a quick help which may give a new life to patients. This system deal with very important patient's data-ECG, SpO$_2$, blood pressure, biomedical signal data etc. - as other emergency system. A good performance better than other system is many but shortly spoken as follows. First, this system is user friendly system activated in windows 2000 environment. Second, MPEG4 and ECG data sent to the other station for specilists can give a pre-hospital cure to patients in advance. Third, there exist effective algorithms to operate this system. Fourth, this system has been made with software mostly, so this system can be easily embedded in IBM compatible computer. In addition to this performance, for the better and reliable system, various tests were proceeded and recursively tested. Tests were made in EV-DO wireless network and Local Area Network. This mobile-fixed remote emergency system using wireless network like EV-DO network will give a great usage to needed area.

• 한국정보통신학회논문지
• /
• 제19권9호
• /
• pp.2081-2086
• /
• 2015

링 발진기를 이용한 온도센서를 공급전압 1.5volts를 사용하여 0.18㎛ CMOS 공정으로 설계하였다. 온도센서는 온도가 변화하더라도 일정한 출력주파수를 가지는 링 발진기와 온도가 증가하면 출력주파수가 감소하는 링 발진기를 이용하여 설계하였다. 온도를 디지털 값으로 변환하기 위해 온도에 무관한 링 발진기의 출력 신호는 카운터의 클럭 신호로 사용하였으며, 온도에 따라 변화하는 링 발진기의 출력신호는 카운터의 인에이블 신호로 사용하였다. 설계된 회로의 HPICE 시뮬레이션 결과 회로의 동작온도가 -20℃에서 70℃까지 변화할 때 온도 에러는 -0.7℃에서 1.0℃ 이내였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 추계학술대회
• /
• pp.793-794
• /
• 2011

본 논문에서는 최근에 디지털논리시스템의 회로 구현시에 적용되기 시작한 분할설계기법의 한가지 방법을 제안하였다. 기존의 디지털논리회로설계기법은 적용되는 개별소자를 어떻게 효과적이며 효율적으로 이용하느냐 하는 것이 큰 목적이었으나, 최근의 전자공학의 발달과 회로의 집적도가 높아짐에 따라서 디지털논리설계기법은 각각의 모듈을 구성하고 있는 소자들의 개별소자를 사용하는 것보다는 복잡하더라도 좀 더 경제적이고 다기능의 분할설계기법이 요구되고 있다. 이러한 내용을 근간으로 본 논문에서는 효과적인 분할기법을 이용한 스위칭함수구성의 한가지 방법을 제안하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 추계학술대회
• /
• pp.687-688
• /
• 2011

본 논문에서는 최근에 디지털논리시스템의 회로 구현시에 적용되기 시작한 분할설계기법의 한가지 방법을 제안하였다. 기존의 디지털논리회로설계기법은 적용되는 개별소자를 어떻게 효과적이며 효율적으로 이용하느냐 하는 것이 큰 목적이었으나, 최근의 전자공학의 발달과 회로의 집적도가 높아짐에 따라서 디지털논리설계기법은 각각의 모듈을 구성하고 있는 소자들의 개별소자를 사용하는 것보다는 복잡하더라도 좀 더 경제적이고 다기능의 분할설계기법이 요구되고 있다. 이러한 내용을 근간으로 본 논문에서는 효과적인 분할기법을 이용한 스위칭함수구성의 한가지 방법을 제안하였다.