• Laser Solutions
• /
• v.16 no.3
• /
• pp.27-31
• /
• 2013

To engrave high-density circuit-line patterns in IC substrates, we applied a projection ablation technique in which a dielectric ($ZrO_2/SiO_2$) mask, a DPSS UV laser instead of an excimer laser, a refractive beam shaping optics and a galvo scanner are used. The line/space dimension of line patterns of the dielectric mask is $10{\mu}m/10{\mu}m$. Using a ${\pi}$ -shaper and a square aperture, the Gaussian beam from the laser is shaped into a square flap-top beam; and a telecentric f-${\theta}$ lens focuses it to a $115{\mu}m{\times}105{\mu}m$ flat-top beam on the mask. The galvo scanner before the f-${\theta}$ lens moves the beam across the scan area of $40mm{\times}40mm$. An 1:1 projection lens was used. Experiments showed that the widths of the engraved patterns in a buildup film ranges from $8.1{\mu}m$ to $10.2{\mu}m$ and the depths from $8.8{\mu}m$ to $11.7{\mu}m$. Results indicates that it is required to increase the projection ratio to enhance profiles of the engraved patterns.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.88-95
• /
• 2008

This paper proposes a fast fault detection algorithm under open-circuit fault of a switch for a brushless DC(BLDC) motor drive system. This proposed method is configured without the additional devices for fault detection and identification. The fault detection and identification are achieved by a simple algorithm using the operating characteristic of the BLDC motor. After the fault identification, the drive system is reconfigured for continuous operation. This system is reconfigured by four-switch topology connecting a faulty leg to the middle point of DC-link bidirectional switches. This proposed method can also be embedded into existing BLDC motor drive systems as a subroutine without excessive computational effort. The feasibility of a the proposed fault detection algorithm is validated in simulation and experiment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.7
• /
• pp.3152-3159
• /
• 2012

This paper presents the new instruction-level power model for an asynchronous processor. Until now, the various power models for estimating the power dissipation of embedded processor in SoC are proposed. Since all of them are target to the synchronous processors, the accuracy is questionable when we apply those power models to the asynchronous processor in SoC. To solve this problem, we present new power model for an asynchronous processor by reflecting the behavioral features of an asynchronous circuit. The proposed power model is verified using an implementation of asynchronous processor, A8051. The simulation results of the proposed model is compared with the measurement result of gate-level synthesized A8051. The proposed power model shows the accuracy of 90.7% and the simulation time for estimation the power consumption was reduced to 1,900 times.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.3
• /
• pp.59-66
• /
• 2015

In this paper, we propose a method of improving the light-load efficiency of DC-DC buck converter using 4bit SAR-ADC (Successive Approximation ADC) for a LDO or a power transistor size selection technique. The proposed circuit selects power transistor sizes depending on load current so that improves the light-load efficiency of the DC-DC buck converter. For this, we select the power transistor size with a cross point of the switching loss and the conduction loss. Also, when the IC operates in standby mode or sleep mode, a LDO mode is selected for improving the efficiency. The proposed circuit selects power transistor sizes(X1, X2, X4, X8) with 4 bits and its efficiency is higher about the maximum of 25% at the light-load than that of a single transistor size. Input voltage and output voltage are 5V and 3.3V for maximum load currents of 500mA.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.893-898
• /
• 2017

A TDC(Time-to-Digital Converter) of counter-type is designed by $0.18{\mu}mCMOS$process and the supply voltage is 1.5 volts. The converted error of maximum $T_{CK}$ is occurred by the time difference between the start signal and the clock when the period of clock is $T_{CK}$ in the conventional TDC. And the converted error of -$T_{CK}$ is occurred by the time difference between the stop signal and the clock. However in order to compensate the disadvantage of the conventional TDC the clock is generated within the TDC circuit and the clock is synchronized with the start and stop signals. In the designed TDC circuit the conversion error is not occurred by the difference between the start signal and the click and the magnitude of conversion error is reduced (1/2)$T_{CK}$ by the time difference between the stop signal and the clock.

• Journal of IKEEE
• /
• v.24 no.3
• /
• pp.853-858
• /
• 2020

This paper proposes a 2-ch DC-DC converter for OLED display with immunity against RF noise inserted from communication device. For RF signal immunity, an input voltage variation reduction circuit that attenuates as much as the input voltage variation is embedded. The boost converter for positive voltage V_POS operates in SPWM-PWM dual mode and has a dead time controller to increase power efficiency. The inverting charge pump for negative voltage V_NEG is a 2-phase scheme and operates in PFM using VCO to reduce output ripple voltage. Simulation results using 0.18 ㎛ BCDMOS process show that the overshoot and undershoot of the output voltage decrease from 10 mV to 2 mV and 5 mV, respectively. The 2-ch DC-DC converter has power efficiency of 39%~93%, and the power efficiency of the boost converter is up to 3% higher than the conventional method without dead time controller.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.1
• /
• pp.83-90
• /
• 2017

The corrosion behavior of a rebar in concrete according to the amount of NaCl and $LiNO_2$ was observed by using Electrochemical Impedance Spectroscopy. The corrosion was accelerated in a short time by using dry/wet cycles method, which is one of the corrosion acceleration methods, and though the value of measured impedance, equivalent circuit can be introduced. It was confirmed that the passive film of a embedded rebar in concrete with NaCl was broken quickly, and when $0.6M\;LiNO_2$ was added, the velocity of ongoing corrosion was declined considerably compared to the amount of NaCl. However, when $1.2M\;LiNO_2$ was added, it was confirmed that the passive film was not broken and its performance remained, compared to the amount of NaCl.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.3
• /
• pp.19-22
• /
• 2013

Recently, high speed transmission and large information demand have been increased. Also, researches of integrated optical device for large production and high-efficient planar lightwave circuit (PLC) have been increased. In this paper, integrated optical alignment is proposed which makes passive alignment between optical device and optical fiber possible. The integrated optical device consists of splitter structures which have one input and two outputs. The proposed integrated structure was fabricated by roll-to-roll (RTR) processing method. This method enables to manufacture continuously and the processing time can be shortened. Optical property of the fabricated optical device showed 3.9 dB insertion loss and 0.2 dB optical uniformity using the light source with 1550 nm wavelength.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.299-302
• /
• 2016

In this paper, we designed the stack monitoring system with improved performance. To block the incoming pulse noise to the amplifier, shield and the power supply impedance are reduced and the power circuit is isolated. The control unit is developed with variable high voltage, adaptive gain, offset and threshold in order to match the scintillation detector characteristic to the apparatus. 300-1500V variable high voltage power circuit is configured applicable to various scintillation detector. Stack monitoring system with improved performance guarantee the efficiency and the reliability by considering the characteristic of various scintillation detector. Developed stack monitoring system is evaluated with certified testing equipment and shows excellent performance with respect to the uncertainty of the sensor test results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.8
• /
• pp.1511-1518
• /
• 2007

As studies on ubiquitous computing are actively conducted, desire for various services, including image transmission storage, search and remote monitoring. has been expanding into mobile environment as well as to PCs. while CCTV (closed circuit TV) and un DVR (Digital video Recording) are used in places where security service such as intrusion detection system is required, these are high-end equipment. So it is not easy for ordinary users or household and small-sized companies to use them. Besides, they are difficult to be carried and camera solution for mobile device does not support high-quality function and provides low-definition of QVGA for picture quality. Therefore, in this study, design and implementation of embedded system of high-definition image transmission for ubiquitous mobile device which is not inferior to PC or DVR are described. To this end, usage of dedicated CPU for mobile device and design and implementation of MPEG-4 H/W CODEC also are examined. The implemented system showed excellent performance in mobile environment, in terms of speed, picture quality.