• Journal of Electrical Engineering and Technology
• /
• 제13권4호
• /
• pp.1438-1449
• /
• 2018

The importance of power system stability has been emphasized with an increase of wind energy penetration in the power system. Accordingly, the guarantee on various control capabilities, including active and reactive power control of wind farms, was regarded as the most important aspect for the connection to the grid. To control the wind farm active power, the wind farm controller was introduced. The wind farm controller decides the power set points for each wind turbine generating unit and each wind turbine generating unit controls its power according to the set points from the wind farm controller. Therefore, co-relationship between wind farm controller and wind turbine controllers are significantly important. This paper proposes some control methods of wind farm active power control based on modified wind turbine control for power system stability and structures to connect wind turbine controllers to wind farm controller. Besides, this paper contributes to development of control algorithm considering not only electrical components but also mechanical components. The proposed contributions were verified by full simulation including power electronics and turbulent wind speed. The scenario refers to the active power control regulations of the Eltra and Elkraft system in Denmark.

• 설비공학논문집
• /
• 제12권5호
• /
• pp.446-475
• /
• 2000

Performance of a water-to-water multi-type heat pump system using R22 has been experimentally investigated. Total refrigerant flow rate was adjusted with a variable speed compressor and the refrigerant flow rate for two indoor units were controlled by electronic expansion valves. Evaporator outlet pressure of refrigerant and indoor unit outlet temperatures of secondary fluid were selected as controlled variables. Experiments were carried out for both cooling and heating modes using PID control method. Results show that the multi-type heat pump system can be adequately controlled by keeping control gains at certain levels for various operating conditions.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.174.2-174
• /
• 2001

Increasing demand for safety features, driving comfort and operational convenience in automobiles requires an intensive use of electronic components such as sensors, actuators and Electronic Control Unit(ECU)'s. These growing number of electronics has given rise to problems concerning the increasing number, size and weight of the wiring harnesses. In order to resolve these problems, multiplexed wiring systems such as Controller Area Network(CAN) serial communication protocol are applied in vehicle. This paper introduces the development of Body Control Module(BCM)s using multiplexed wiring systems. The BCM's were developed and implemented using CAN, the most popular choice of in-vehicle communication protocols.

• 한국전자통신학회논문지
• /
• 제7권2호
• /
• pp.309-315
• /
• 2012

선박이나 해양구조물의 해양에서의 위치를 고정하고자 할 경우에 적용되는 자동 윈치 제어 시스템을 개발하였다. 본 논문에서는 윈치제어목적을 위하여 제어유닛의 설계하고 개발하였다. 개발된 결과는 한강 인공섬에 적용하여 개발내용의 유용성을 보여주었다.

• 한국전자통신학회논문지
• /
• 제5권5호
• /
• pp.504-508
• /
• 2010

현 농촌사회는 점차 고령화 사회가 되어감에 따라 노동력 감소 문제점이 발생하고 있다. 본 연구을 통하여 생육 단계별 수위를 자동 컨트롤하여 관리할 수 있는 농작물의 수위 조절 시스템 연구 개발하였다. 수위측정에는 초음파 센서를, 급 배수로의 수문 제어에는 서보모터를 사용하고 이들의 신호를 처리하는 제어부로는 ATmega128을 사용하였다. 본 시스템을 통하여 노동력 감소의 문제점을 해결하고 농촌사회의 자동화 발전 및 고령화 사회에 큰 기여를 기대 할 수 있을 것이다.

• KIEE International Transactions on Power Engineering
• /
• 제3A권1호
• /
• pp.27-34
• /
• 2003

In this paper, the power conditioner composed of the stand-alone single-phase squirrel cage rotor type self-excited induction generator (SEIG) driven by prime movers such as a wind turbine and a micro gas turbine (MGT) is presented by using the steady-state circuit analysis based on the two nodal admittance approaches using the per-unit frequency in addition to a new state variable defined by the per-unit slip frequency along with its performance evaluations for the stand-alone energy utilizations. The stande-alone single-phase SEIG operating performances in unregulated voltage control loop are then evaluated on line under the conditions of the speed change transients of the prime mover and the stand-alone electrical passive load power variations with the simple theoretical analysis and the efficient computation processing procedures described in the part I of this paper. In addition, a feasuible PI controlled feedback closed-loop voltage regulation scheme of the stande-alone single-phase SEIG is designed on the basis of the static VAR compensate. (SVC) and discussed in experiment for the promising stand-alone power conditioner. The experimental operating performance results are illustrated and give good agreements with the simulation ones. The simulation and experimental results of the stand-alone single-phase SEIG with the simple SVC controller for its stabilized voltage regulation prove the practical effectiveness of the additional SVC control loop scheme including the PI controller with fast response characteristics and steady-sate performance improvements.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2021년도 춘계학술대회
• /
• pp.267-270
• /
• 2021

자동차 진단을 위해서는 자동차 전자 장치인 ECU(Electronic Control Unit)로 구성된 전자 장치를 통해 다양한 통신방식을 활용하여 ECU 내 또는 ECU 간 진단 데이터를 수집하고 진단데이터를 관리하여 이뤄지고 있다. 통신 방식으로는 LIN, CAN, FlexRay 등이 주로 사용되고 있다. 최근에는 Ethernet 기반으로 유선/무선 통신을 활용하고 있다. 자동차 진단을 수행하려면 ECU에서 발생되는 진단코드를 알고 있어야 하고, 진단통신을 이용하여 진단 데이터를 수집할 수 있어야 가능하다. 또한, 자동차 진단에 필요한 응용소프트웨어가 구성되어야 ECU로부터 진단데이터를 관리할 수 있다. 많은 자동차 제조사가 자동차 전장 표준인 AUTOSAR 표준을 기반으로 ECU를 제작하고 있으면, 소프트웨어 구조 또한 표준에 따라 적용될 수 있도록 구성되어 있다. 본 논문에서는 AUTUSAR 표준의 자동차 진단 통신 방식을 이해하고 진단 데이터 구성과 처리 방식에 대해서 연구하였으며, 소프트웨어 컴포넌트와 진단통신, 진단 이벤트 처리에 대한 내용에 대해서 연구하였다.

• 전자통신동향분석
• /
• 제34권1호
• /
• pp.123-131
• /
• 2019

Automotive electronics are complex and require high performance with an advanced driver assistant system (ADAS) and a functioning autonomous system. Thus, considering their complexity, the processor of the electronic control unit (ECU) requires a design that ensures high performance and reliability to ensure functional safety. This study discusses the technology used for developing a processor that can ensure functional safety of current automotive electronic systems.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.1-8
• /
• 2013

Remanufacturing of automobile parts is important for increasing the recycling resources. ECU(Electronic Control Unit) systems are becoming an increasingly important part of an automobile. But production company are reported in the ECU remanufacturing industry of domestic automobile parts due to a lack of remanufacturing technology and marketability. This paper introduces the ECU of remanufacturing, also grasps the structure and the analyzes failure cause that is external factors and fault in the characteristic design and steps in the Independent ECU remanufacturing process. The ECU manufacturing industry of the US was examined. The results in this paper could be used as the system information for further remanufacturing industry of domestic automobile parts.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2003년도 Proceedings of ACRS 2003 ISRS
• /
• pp.1121-1123
• /
• 2003

The CCD (Charge coupled device) detector that is used to convert the light into electronic data is very important component in satellite camera. A Linear CCD Spectral detector shall be used in the MSC (Multi-Spectral Camera, to obtain data for high-resolution images) Payload. In this paper, the design concept of the CCD detector control module in the MSC CEU (Camera electronic unit) system which will be a payload on KOMPSAT is described in terms of H/W (clock speed and accuracy).