• Preventive Nutrition and Food Science
• /
• v.4 no.1
• /
• pp.6-13
• /
• 1999

The quality of the buckwheat bread made with previously heated ($55^{\circ}C$) and cooled buckwheat flour 0dough with the addition of ascorbic acid(AA) or/and sodium stearoyl lactylate(SSL) was evaluated . With heat treatemtn , handling property of dough and grain of the bread crumb were markedly improved and stickiness of the dough decreased . The optimum resting time to produce the best loaf volume and grain was found to be 3hr for both unheated and heated doughs. Heat treated dough showed higher dough expansion rate during fermentation than unheated dough, even though heated dough had lower loaf volume, probably because of an improper oven spring. Increase in shortening of dough formula from 3% to 5% improved loaf volume without improvement of handling property. With the addition of 100 ppm AA or/and 0.5% SSL, loaf volume and crumb grain were improved for both unheated and heated doughs.Microscopic analysis of a mixed dough by scanning electron microscope (SEM) showed that heated dough had a continuous network whereas unheated dough was discontinuous. The addition of AA and SSL gave the dough a more continuous network whereas unheated dough was discontinuous . The addition of AA and SSL gave the dough a more continuous structure with strengthened strands or interactions between the starch granule and protein. Therefore, it appears that the presence of continuity in heated buckwheat breadwheat bread dough is related to the improved loaf volume and crumb grain without dough stickness.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.628-634
• /
• 2014

In this study, a new paint which is able to resist the cavitation erosion is tried to be developed by using urethane added with polyol such as poly propylene glycol(PPG), poly carbonate diol(PCD), polycaprolactone polyol (PCL-1), and poly caprolactone-tetramethylene gylcolether polyol(PCL-2). The new paint synthesized by adding polyol was characterized with physical properties and resistivity to cavitation erosion. Among polyol, the prepolymer added with PCD showed high hardness and wear resistance. However, due to too high in viscosity, the prepolymer added with PCL-1 was selected as a paint. The paint added with PCL-1 showed high resistivity to cavitation erosion and its surface was monitored by using Scanning Electron Microscope.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.1
• /
• pp.35-40
• /
• 2004

Rotavirus virus-like particle (VLP) composed of VP2, VP6, and VP7 was expressed in the Baculovirus Expression Vector System (BEVS). Sf9 cell, a host of the baculovirus, was cultured from a 0.5-1 spinner flask to the 50-1 bioreactor system. Sf9 cell was maintained at cell density between 3.0E＋05 and 3.0E＋06 cells/ml and grew up to 1.12E＋07 cells/ml in the bioreactor. Growth kinetics was compared under different culture systems and showed similar growth kinetics with 20.1-25.2 h of doubling time. Early exponentially growing cell culture was infected with three recombinant baculoviruses expressing VP2, VP6, and VP7 protein at 1.0, 2.0, and 0.2 moi, respectively. The expression of rotavirus proteins was confirmed by Western blot analysis and its three-layered virus-like structure was observed under an electron microscope. Rotavirus VLP was semipurified and immunized in ICR mice intramuscularly. Rotavirus-specific serum antibody was detected from 2 weeks after the immunization and lasted at least 21 weeks of the post-immunization, indicating its possible use as a vaccine candidate.

• Current Research on Agriculture and Life Sciences
• /
• v.31 no.1
• /
• pp.18-24
• /
• 2013

This work attempted to fabricate organic/inorganic nanocomposite by combining organic cellulose nanofibrils (CNFs), isolated by 2,2,6,6-tetramethylpiperidine-1-oxy radical (TEMPO)-mediated oxidation of native cellulose with inorganic nanoclay. The morphology and dimension of CNFs, and tensile properties and thermal stability of CNF/clay nanocomposites were characterized by transmission electron microscope (TEM), tensile test, and thermogravimetry (TG), respectively. TEM observation showed that CNFs were fibrillated structure with a diameter of about $4.86{\pm}1.341nm$. Tensile strength and modulus of the hybrid nanocomposite decreased as the clay content of the nanocomposite increased, indicating a poor dispersion of CNFs or inefficient stress transfer between the CNFs and clay. The elongation at break increased at 1% clay level and then continuously decreased as the clay content increased, suggesting increased brittleness. Analysis of TG and derivative thermogravimetry (DTG) curves of the nanocomposites identified two thermal degradation peak temperatures ($T_{p1}$ and $T_{p2}$), which suggested thermal decomposition of the nanocomposites to be a two steps-process. We think that $T_{p1}$ values from $219.6^{\circ}C$ to $235^{\circ}C$ resulted from the sodium carboxylate groups in the CNFs, and that $T_{p2}$ values from $267^{\circ}C$ to $273.5^{\circ}C$ were mainly responsible for the thermal decomposition of crystalline cellulose in the nanocomposite. An increase in the clay level of the CNF/clay nanocomposite predominately affected $T_{p2}$ values, which continuously increased as the clay content increased. These results indicate that the addition of clay improved thermal stability of the CNF/clay nanocomposite but at the expense of nanocomposite's tensile properties.

• Ecology and Resilient Infrastructure
• /
• v.3 no.4
• /
• pp.215-220
• /
• 2016

A new immobilization technique of nanoscale $TiO_2$ powder to expanded polystyrene (EPS) balls with temperature-controlled melting method was developed, and the photocatalytic activity of $TiO_2$ powder-embedded EPS balls were evaluated using methylene blue (MB) solution under ultraviolet irradiation (${\lambda}=254nm$). Based on the scanning electron microscope (SEM) images and associated energy-dispersive X-ray spectroscopy (EDX) analysis, the components of the intact EPS balls were mainly carbon and oxygen, whereas those of $TiO_2$-immobilized EPS balls were carbon, oxygen, and titanium, indicating that relatively homogenous patches of $TiO_2$ and glycerin film were coated on the surface of EPS balls. Based on the comparison of degradation efficiencies of MB between intact and $TiO_2$-immobilized EPS balls under UVC illumination, the degradation efficiencies of MB can be significantly improved using $TiO_2$-immobilized EPS balls, and surface reactions in heterogeneous photocatalysis were more dominant than photo-induced radical reactions in aqueous solutions. Thus, $TiO_2$-immobilized EPS balls were found to be an effective photocatalyst for photodegradation of organic compounds in aqueous solutions without further processes (i.e., separation, recycling, and regeneration of $TiO_2$ powder). Further study is in progress to evaluate the feasibility for usage of buoyant $TiO_2$-immobilized EPS to inhibit the excessive growth of algae in rivers and lakes.

• Journal of Sensor Science and Technology
• /
• v.23 no.3
• /
• pp.207-210
• /
• 2014

$TiO_2$ oxide semiconductor is being widely studied in various applications such as photocatalyst and photosensor. Pd/$TiO_2$ gas sensor is mainly used to detect $H_2$, CO and ethanol. This study focus on increasing hydrogen detection ability of Pd/$TiO_2$ in room temperature through Al-doping. Pd/$TiO_2$ was fabricated by the hydrothermal method. Contacting to Aluminum (Al) foil led to Al doping effect in Pd/$TiO_2$ by thermal diffusion and enhanced hydrogen sensing response. $TiO_2$ nanoparticles were sized at ~30 nm of diameter from scanning electron microscope (SEM) and maintained anatase crystal structure after Al doping from X-ray diffraction analysis. Presence of Al in $TiO_2$ was confirmed by X-ray photoelectron spectroscopy at 73 eV. SEM-energy dispersive spectroscopy measurement also confirmed 2 wt% Al in Pd/$TiO_2$ bulk. The gas sensing test was performed with $O_2$, $N_2$ and $H_2$ gas ambient. Pd/Al-doped $TiO_2$ did not response $O_2$ and $N_2$ gas in vacuum except $H_2$. Finally, the normalized resistance ratio ($R_{H2on}/R_{H2off}$) of Pd/Al-doped $TiO_2$ increases about 80% compared to Pd/$TiO_2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.158-158
• /
• 2009

The electrophoretic deposition(EPD) technique with a wide range of novel applications in the processing of advanced ceramic materials and coatings, has recently gained increasing interest both in academic and industrial sector not only because of the high versatility of its use with different materials and their combinations but also because of its cost-effectiveness requiring simple apparatus. Compared to other advanced shaping techniques, the EPD process is very versatile since it can be modified easily for a specific application. For example, deposition can be made on flat, cylinderical or any other shaped substrate with only minor charge in electrode design and positioning[1]. The synthesis of the nano-sized Ce0.2Sm0.8O1.9(SDC)particles prepared by aurea based low temperature hydrothermal process was investigated in this study[2].When we made the SDC nanoparticles, changed the time of synthesis of the SDC. The SDC nanoparticles were characterized with field-emission scanning electron microscope(FESEM), energy dispersive X-ray analysis(EDX), and X-ray diffraction(XRD). And also we researched the results of our investigation on electrophoretic deposition(EPD) of the SDC particles from its suspension in acetone solution onto a non-conducting NiO-SDC substrate. In principle, it is possible to carry out electrophoretic deposition on non-conducting substrates. In this case, the EPD of SDC particles on a NiO-SDC substrate was made possible through the use of a adequately porous substrate. The continuous pores in the substrates, when saturated with the solvent, helped in establishing a "conductive path" between the electrode and the particles in suspension[3-4]. Deposition rate was found to increase its increasing deposition time and voltage. After annealing the samples $1400^{\circ}C$, we observed that deposited substrate.

• Journal of the Korean Vacuum Society
• /
• v.17 no.3
• /
• pp.204-210
• /
• 2008

ZnO thin films were grown on a glass by RF sputtering system with RF power 100W and oxygen partial pressure of $0%{/sim}30%$. Elliptic constants were measured by using a phase modulated spectroscopic ellipsometer and analyzed with the Tauc-Lorentz dispersion formula and best fit method in the range of 1.5 to 3.8eV. Also, scanning electron microscope(SEM) was used for the analysis of surface crystallization condition. From elliptic constants spectra, optical constants, thickness and roughness of ZnO films were evaluated. Total thickness of ZnO films obtained by ellipsometry showed good agreement with SEM data. It was found that the grain size of the films were getting smaller with increasing oxygen partial pressure. Band-gap of ZnO films increase with the oxygen partial pressure. These findings clearly indicate that optical properties of ZnO films are strongly dependent on the oxygen partial pressure. It could be explained that increasing the oxygen partial pressure induced high crystalline imperfection in the ZnO films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.104-104
• /
• 2011

ZnO는 3.37 eV의 넓은 에너지 밴드갭을 갖는 투명 전도성 반도체이며 우수한 전기적, 광학적 특성으로 인해 광원소자 개발을 위한 새로운 물질로 많은 주목을 받아왔다. 더욱이, ZnO는 쉽게 나노구조 형성이 가능하기 때문에 이를 응용한 가스센서, 염료감응태양전지, 광검출기 등의 소자 개발이 활발히 이루어지고 있다. 최근에는 GaN 기반 발광다이오드 (light emitting diode, LED)의 광추출 효율을 향상시키기 위한 ZnO 나노구조 응용에 관한 연구가 보고되고 있다. GaN 기반 LED의 경우 반도체 물질과 공기 사이의 높은 굴절률 차이로 인하여 낮은 광추출 효율을 나타낸다. 이를 해결하기 위한 방법으로 표면 roughening, texturing 등 에칭공정을 이용해 광추출 효율을 개선하려는 연구들이 보고되고 있으나, 복잡한 공정과정을 필요로 하고 에칭공정에 의한 소자 표면 손상으로 전기적 특성이 나빠질 수 있다. 반면 전기화학증착법으로 성장된 ZnO 나노구조를 이용할 때, 보다 간단한 방법으로 쉽고 빠르게 나노구조를 형성할 수 있고 낮은 공정온도를 가지기 때문에 소자의 전기적 특성에 큰 영향을 주지 않는다. 수직방향으로 잘 정렬된 ZnO 나노구조를 갖는 LED의 경우 내부 Fresnel 반사 손실을 효과적으로 줄여 발광 효율을 크게 향상시킬 수 있다. 따라서, ZnO 나노구조의 성장제어 및 성장특성을 분석하는 것은 매우 중요하다. 본 연구에서는 ITO glass 위에 ZnO 나노구조를 성장하고 그 특성을 분석하였다. ITO glass 기판 위에 RF magnetron 스퍼터를 사용하여 Al 도핑된 ZnO (AZO)를 얇게 증착한 후 전기화학증착법으로 ZnO 나노구조를 성장하였다. 농도, 인가전압, 공정시간 등 다양한 공정조건을 변화시키면서 성장 메커니즘을 분석하였고, scanning electron microscope (SEM) 및 X-ray diffraction (XRD)을 통하여 구조 및 결정성 등을 분석하였다. 또한, UV-Visible-NIR spectrophotometer를 사용하여 투과율을 실험적으로 측정하여 ZnO 나노구조의 광학적 특성을 분석하였고, rigorous coupled wave analysis (RCWA) 방법을 사용하여 계면에서 발생하는 내부 반사율을 계산함으로써 나노구조의 효과를 이론적으로 분석하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.337-337
• /
• 2012

Dye sensitized solar cell (DSSC) having high efficiency with low cost was first reported by Gr$\ddot{a}$tzel et al. Many DSSC research groups attempt to enhance energy conversion efficiency by modifying the dye, electrolyte, Pt-coated electrode, and $TiO_2$ films. However, there are still some problems against realization of high-sensitivity DSSC such as the recombination of injected electrons in conduction band and the limited adsorption of dye on $TiO_2$ surface. The surface of $TiO_2$ is very important for improving hydrophilic property and dye adsorption on its surface. In this paper, we report a very efficient method to improve the efficiency and stability of DSSC with nano-structured $TiO_2$. Atmospheric plasma system was utilized for nitrogen plasma treatment on nano-structured $TiO_2$ film. We confirmed that the efficiency of DSSC was significantly dependent on plasma power. Relative in the $TiO_2$ surface change and characteristics after plasma was investigated by various analysis methods. The structure of $TiO_2$ films was examined by X-ray diffraction (XRD). The morphology of $TiO_2$ films was observed using a field emission scanning electron microscope (FE-SEM). The surface elemental composition was determined using X-ray photoelectron spectroscopy (XPS). Each of plasma power differently affected conversion efficiency of DSSC with plasma-treated $TiO_2$ compared to untreated DSSC under AM 1.5 G spectral illumination of $100mWcm^{-2}$.