• 한국기계가공학회지
• /
• 제16권2호
• /
• pp.7-15
• /
• 2017

Recently, an electricity sensor system has been installed and operated to prevent failures and accidents by identifying whether a transformer is normal in advance of failure. This electricity sensor system is able to both measure and monitor the transformer's power and voltage remotely and send information to a manager when unusual operation is discovered. However, a battery is required to operate power detection devices, and battery systems need ongoing management such as regular replacement. In addition, at a maintenance cost, occasional human resources and worker safety problems arise. Accordingly, we apply a linear electromagnetic generator using vibration energy from a transformer for an electric sensor system's drive in this research and we conduct optimal design to maximize the linear electromagnetic generator's power. We consider design variables using the provided design method from Process Integration, Automation, and Optimization (PIAnO), which is common tool from process integration and design optimization (PIDO). In addition, we analyze the experiment point from the design of the experiments using "MAXWELL," which is a common electromagnet analysis program. We then create an approximate model and conduct accuracy verification. Finally, we determine the optimal model that generates the maximum power using the proven approximate kriging model and evolutionary optimization algorithm, which we then confirm via simulation.

• 한국분말재료학회지
• /
• 제16권4호
• /
• pp.291-295
• /
• 2009

The electromagnetic wave absorption sheets were fabricated by mixing of $Fe_{73}Si_{16}B_7Nb_3Cu_1$ nanocrystalline soft magnetic powder, charcoal powder and polymer based binder. The complex permittivity, complex permeability, and scattering parameter have been measured using a network analyzer in the frequency range of 10 MHz$\sim$10 GHz. The results showed that complex permittivity of sheets was largely dependent on the frequency and the amount of charcoal powder : The permittivity was improved up to 100 MHz, however the value was decreased above 1 GHz. The power loss of electromagnetic wave absorption data showed almost the same tendency as the results of complex permittivity. However, the complex permeability was not largely affected by the frequency, and the values were decreased with the addition of charcoal powder. Based on the results, it can be summarized that the addition of charcoal powder was very effective to improve the EM wave absorption in the frequency range of 10 MHz$\sim$1 GHz.

• 한국전자파학회논문지
• /
• 제28권12호
• /
• pp.954-963
• /
• 2017

본 연구에서는 공진형 무선전력전송시스템에 의해 발생되는 자기장과 전기장 강도 및 이에 의한 인체 내부 전자파 비흡수율(Specific Absorption Rate: SAR) 분포를 분석하였다. 연구에서 사용된 동작주파수는 ISM 대역에 해당하는 6.78 MHz이다. 실제 시스템을 제작하고, 시스템의 송신측에 공급되는 가용 전력을 1 W로 제한하여 전기장 및 자기장 분포를 측정하고, 동일한 규격으로 시뮬레이션한 결과와 비교하였다. 피부, 지방, 근육의 순으로 조직층이 구성된 단순인체모델을 이용하여, WPT 시스템으로부터의 거리에 따른 인체 내부의 유도 전류밀도와 SAR 분포를 구하였다. 측정과 시뮬레이션을 통해 얻어진 전자파 노출 정도를 ICNIRP(International Commission on Non-Ionizing Radiation Protection)의 국제 권고기준과 비교하여 분석하였다.

• 한국건축시공학회지
• /
• 제18권5호
• /
• pp.463-469
• /
• 2018

기존의 다층으로 구성되어 시공성이 낮은 옥상녹화 공법의 개선을 위해 개발한 방수 방근 시트 일체화 옥상녹화박스 유닛공법의 일체화를 위해 사용하는 전자기 유도가열방식의 금속 고정구와 콘 형상 고정구의 부착성능을 평가하기 위해 엔지니어링 PE, TPO, PVC 시트 등 3종류의 시트에 가열온도에 따른 부착성능 및 동일한 시험체로 냉열반복 후 부착성능을 측정하였다, 그 결과는 엔지니어링 PE시트에 부착한 고정구의 부착성능이 가장 우수하게 나타났으며, 금속고정구는 가열온도가 올라갈수록, 콘 형상 고정구는 가열온도가 낮을수록 우수한 부착성능을 보여주었고, 냉열 반복 후 부착시험 결과는 상온 부착시험 결과와 동일하게 나타났다. 기존의 양면 부틸테이프 고정방식의 콘 형상 고정구는 낮은 부착하중과 냉열반복에 의한 뚜렷한 성능저하가 발생하는데 비하여 전자기 유도가열방식의 고정구는 우수한 성능을 유지하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.227-231
• /
• 2014

Underwater radiated noise is one of the vital factors in underwater weapon systems like submarine. A passive elastic mount is an effective reduction method for the vibration from a ship-board machinery transmitted to the hull which is radiated as noise outside the hull. A passive elastic mount shows the limitation on the vibration reduction and needs multi stage mounting system including double stage one to meet the required underwater radiated noise criteria. It is necessary for the multi stage mounting system to consider the large displacement in the underwater shock explosion. So it is difficult to apply the multi stage mounting system in submarine because of space limitation. Also recent navy sonar system are trying to have the capability to detect the ship-borne acoustic signals in the low frequency range. An alternative to the passive mount is an active mount with moving-coil type electromagnetic actuator based on a conventional rubber mount in the low frequency range. In the previous paper, 4 active mounts with moving-coil type electromagnetic actuator based on the rubber mount were installed on the hard floor of the facility, which means no consideration on the elastic foundation effect for the control of the active mounts was taken into account. In this study, an experimental performance analysis on the active mount was carried out using 4 active mounts installed on the cylindrical structure to investigate the elastic foundation effect.

• 한국전기전자재료학회논문지
• /
• 제31권1호
• /
• pp.44-49
• /
• 2018

This study analyzed the Vulnerability of Network Communication devices when IEMI is coupled with the Network System. An Ultra Wide Band Generator (180 kV, 700 MHz) was used as the IEMI source. The EUTs are the Switch Hub and Workstation, which are used to configure the network system. The network system was monitored through the LAN system configuration, to confirm a malfunction of the network device. The results of the experiment indicate that a malfunction of the network occurs as the electric field increases. The data loss rate increases proportionally with increasing radiating time. In the case of the Switch Hub, the threshold electric field value was 10 kV/m for all conditions used in this experiment. The threshold point causing malfunction was influenced only by the electric field value. The correlation between the threshold point and pulse repetition rate was not found. However, in case of the Workstation, it was found that as the pulse repetition rate increases, the equipment responds weakly and the threshold value decreases. To verify the electrical coupling of the EUT by IEMI, current sensors were used to measure the PCB line inside the EUT and network line coupling current. As a result of the measurement, it can be inferred that when the coupling current due to IEMI exceeds the threshold value, it flows through the internal equipment line, causing a malfunction and subsequent failure. The results of this study can be applied to basic data for equipment protection, and effect analysis of intentional electromagnetic interference.

• ETRI Journal
• /
• 제43권5호
• /
• pp.869-880
• /
• 2021

Herein, we estimate the direction of arrival (DOA) of non-Gaussian signals for nested arrays (NAs) by implementing the fourth-order difference co-array (FODC) and successive methods. In particular, considering the property of the fourth-order cumulant (FOC), we first construct the FODC of the NA, which can obtain O(N⁴) virtual elements using N physical sensors, whereas conventional FOC methods can only obtain O(N²) virtual elements. In addition, the closed-form expression of FODC is presented to verify the enhanced degrees of freedom (DOFs). Subsequently, we exploit the vectorized FOC (VFOC) matrix to match the FODC of the NA. Notably, the VFOC matrix is a single snapshot vector, and the initial DOA estimates can be obtained via the discrete Fourier transform method under the underdetermined correlation matrix condition, which utilizes the complete DOFs of the FODC. Finally, fine estimates are obtained through the spatial smoothing-Capon method with partial spectrum searching. Numerical simulation verifies the effectiveness and superiority of the proposed method.

• Biomolecules & Therapeutics
• /
• 제27권3호
• /
• pp.265-275
• /
• 2019

Technological advances of mankind, through the development of electrical and communication technologies, have resulted in the exposure to artificial electromagnetic fields (EMF). Technological growth is expected to continue; as such, the amount of EMF exposure will continue to increase steadily. In particular, the use-time of smart phones, that have become a necessity for modern people, is steadily increasing. Social concerns and interest in the impact on the cranial nervous system are increased when considering the area where the mobile phone is used. However, before discussing possible effects of radiofrequency-electromagnetic field (RF-EMF) on the human body, several factors must be investigated about the influence of EMFs at the level of research using in vitro or animal models. Scientific studies on the mechanism of biological effects are also required. It has been found that RF-EMF can induce changes in central nervous system nerve cells, including neuronal cell apoptosis, changes in the function of the nerve myelin and ion channels; furthermore, RF-EMF act as a stress source in living creatures. The possible biological effects of RF-EMF exposure have not yet been proven, and there are insufficient data on biological hazards to provide a clear answer to possible health risks. Therefore, it is necessary to study the biological response to RF-EMF in consideration of the comprehensive exposure with regard to the use of various devices by individuals. In this review, we summarize the possible biological effects of RF-EMF exposure.

• 한국정보통신학회논문지
• /
• 제24권9호
• /
• pp.1215-1223
• /
• 2020

최근 서울 경기를 비롯한 전국에서 국지성 집중호우, 태풍 등 악천후 관련 자연재해가 증가함에 따라 이에 대한 방재 및 물관리 대책이 필요한 실정이다. 이러한 수재해를 관측하기 위해 사용되는 우량계는 지상의 강우를 연속적·직접적으로 측정할 수 있는 장점이 있는 반면, 우량계 미설치 영역에 대한 공간적인 강우 분포를 정확하게 제공할 수 없다. 이러한 문제를 해결하고자 강수의 공간분포를 측정할 수 있는 전자파 기반 센서인 전파강수계(EWRG, Electromagnetic Wave Rain Gauge)를 개발하였다. 본 논문에서는 전파강수계의 FPGA 기반 신호처리 설계 방법을 제안한다. 전파강수계의 신호처리는 크게 LFM 파형의 ADC 및 DDC와 펄스압축, 상관 계수 및 강수 파라미터 산정으로 설계하였다. 본 연구를 통해 LFM 파형과 펄스압축 신호를 이론적으로 분석하였으며, 전파강수계 신호처리 설계를 위해서 FPGA 기반의 신호처리 설계 및 검증을 수행하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.618-622
• /
• 2004

The vibration test system of SITC(Satellite Integration and Test Center) at KARI(Korea Aerospace Research Institute) has been used successfully for the environmental tests of a majority of korean space programs, such as KOMPSAT, Koreasat KITSAT, STSAT and KSR program since 1996. To meet the recent needs of large size test facility available for the vibrational tests of the huge launch vehicles and tole-communication satellites which will be developed in the near future, KARI undertook to construct the large size multi-electromagnetic shaking system with 3 $\times$ 3m head expander system. The new system will consist of three electromagnetic shakers which has 160 kN thrust force individually, and be able te sustain up to 8 tons test load and 300 kNm overturing moment. And to avoid the tremendous cost and effort to furnish the seismic block with large size and weight, it will adopt a Lin-E-Air type configuration with which the seismic block is less severe than a Solid-Truninon type. In addition, to fulfill the strong requirement of high overturning moment the additional guidance system including a central bearing system on a central support and several pad bearings around the head expander body is now considered. This paper describes the configuration and the design parameters of the multi-shaking system which is under development by KARI's engineers.