• Earthquakes and Structures
• /
• v.13 no.1
• /
• pp.51-58
• /
• 2017

Passive dynamic vibration absorbers (DVAs) are often used to suppress the excessive vibration of a large structure due to their simple construction and low maintenance cost compared to other vibration control techniques. A new type of passive DVA consists of two pendulums connected with spring and dashpot element is investigated. This research evaluated the performance of the DVA in reducing the vibration response of a two degree of freedom shear structure. A model for the two DOF vibration system with the absorber is developed. The nominal absorber parameters are calculated using a Genetic Algorithm(GA) procedure. A parametric study is performed to evaluate the effect of each absorber parameter on performance. The simulation results show that the optimum condition for the absorber frequencies and damping ratios is mainly affected by pendulum length, mass, and the damping coefficient of the pendulum's hinge joint. An experimental model validates the theoretical results. The simulation and experimental results show that the proposed technique is able be used as an effective alternative solution for reducing the vibration response of a multi degree of freedom vibration system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.10a
• /
• pp.5-18
• /
• 1993

This paper reports the recent trends in active vibration control in Japan, especially, based on papers selected in the Proceedings of First International Conference on Motion and Vibration Control (1st MOVIC) held at Yokohama, Japan on Sept.7-11, 1992. Firstly, it classifiers vibration control methods and vibration controllers, especially active dynamic absorbers which are widely used in mechanical and civil engineering. Secondly, it covers basic problems in the control of vibration of flexible structures such as formulating a reduced-order model required for designing vibration controller, proper arranging of sensors and actuators, and preventing of spillover instability. Finally, the practical use of control theories such as LQ control theory, $H^{\infty}$ control theory, neural network theory, and other topics are discussed..

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.222-227
• /
• 2002

MR(Magneto-rheological) fluid is smart fluid that can change its characteristics then magnetic fields are applied. Recently, many researches have been performed on this MR fluid for the application in a vareity of areas including automobile shock absorbers. This paper describes the design procedure of a MR damper and the analysis results of its dynamic characteristics. MR fluid in the magnetic field shows initial yield shear stress and increasing resistive viscosity with final saturation thereafter. Herschel-Bulkley model is used to simulate the flow characteristics of MR fluid and magnetic analysis is used to identify the magnetic property of the MR fluid in the orifice of the damper. The dynamic characteristics of the damper was predicted and compared with the experimental results for typical sinusoidal excitations.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.328.1-328
• /
• 2002

MR(Magneto-rheological) fluid is smart fluid that can change its characteristics when magnetic fields are applied. Recently, many researches are going on this MR fluid for the application in a variety of areas including automobile shock absorbers. This paper describes the design procedure of a MR damper and the analysis results of its dynamic characteristics. MR fluid in the magnetic field shows initial yield shear stress and increasing resistive viscousity with final saturation thereafter. (omitted)

• International Journal of Safety
• /
• v.6 no.1
• /
• pp.7-10
• /
• 2007

In this paper, we found that modification of the local flexibility (or local stiffness) of the 4 parts on which shock absorbers are mounted in the vehicle body has some influence the level of ride safety and comfort. Multi-body dynamic analysis considering the flexibility of the vehicle body is performed using MSC/ADAMS and MSC/NASTRAN. More concretely speaking, natural frequencies and mode shapes computed by MSC/NASTRAN are used as input data for multi-body dynamic analysis in MSC/ADAMS. It is confirmed that the ride comfort can be improved by appropriately changing the local stiffness of the vehicle body through several simulations using MSC/ADAMS.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.3
• /
• pp.1-18
• /
• 1995

This paper deals with the vibration absorbers of gravitational and centrifugal pendulum types for vibration controls of ship's substructures such as radarmasts, bridgewings and funnels. The mathematical model of such a vibrating system with an absorber is described as a 2 degree of freedom system and an efficient formulation for optimum design of the absorber is presented. For investigation applicability of the two types of the absorbers to a structure system, numerical calculations and experiments hove been performed with variation of mass ratios for each type. According to the results of investigations, the vibration absorber of gravitational type proved to be more useful and efficient than one of centrifugal pendulum type in a view point of mass ratio.

• Smart Structures and Systems
• /
• v.13 no.2
• /
• pp.203-217
• /
• 2014

Due to the shift in paradigm from passive control to adaptive control, smart tuned mass dampers (STMDs) have received considerable attention for vibration control in tall buildings and bridges. STMDs are superior to tuned mass dampers (TMDs) in reducing the response of the primary structure. Unlike TMDs, STMDs are capable of accommodating the changes in primary structure properties, due to damage or deterioration, by tuning in real time based on a local feedback. In this paper, a novel adaptive-length pendulum (ALP) damper is developed and experimentally verified. Length of the pendulum is adjusted in real time using a shape memory alloy (SMA) wire actuator. This can be achieved in two ways i) by changing the amount of current in the SMA wire actuator or ii) by changing the effective length of current carrying SMA wire. Using an instantaneous frequency tracking algorithm, the dominant frequency of the structure can be tracked from a local feedback signal, then the length of pendulum is adjusted to match the dominant frequency. Effectiveness of the proposed ALP-STMD mechanism, combined with the STFT frequency tracking control algorithm, is verified experimentally on a prototype two-storey shear frame. It has been observed through experimental studies that the ALP-STMD absorbs most of the input energy associated in the vicinity of tuned frequency of the pendulum damper. The reduction of storey displacements up to 80 % when subjected to forced excitation (harmonic and chirp-signal) and a faster decay rate during free vibration is observed in the experiments.

• Wind and Structures
• /
• v.38 no.1
• /
• pp.15-42
• /
• 2024

A flexible-base coupled-two-beam (CTB) discrete model with equivalent tuned mass dampers is used to assess the effect of soil-structure interaction (SSI) and different types of lateral resisting systems on the design of passive dynamic absorbers (PDAs) under the action of along-wind and across-wind loads due to vortex shedding. A total of five different PDAs are considered in this study: (1) tuned mass damper (TMD), (2) circular tuned sloshing damper (C-TSD), (3) rectangular tuned sloshing damper (R-TSD), (4) two-way liquid damper (TWLD) and (5) pendulum tuned mass damper (PTMD). By modifying the non-dimensional lateral stiffness ratio, the CTB model can consider lateral deformations varying from those of a flexural cantilever beam to those of a shear cantilever beam. The Monte Carlo simulation method was used to generate along-wind and across-wind loads correlated along the height of a real shear wall-frame building, which has similar fundamental periods of vibration and different modes of lateral deformation in the xz and yz planes, respectively. Ambient vibration tests were conducted on the building to identify its real lateral behavior and thus choose the most suitable parameters for the CTB model. Both alongwind and across-wind responses of the 144-meter-tall building were computed considering four soil types (hard rock, dense soil, stiff soil and soft soil) and a single PDA on its top, that is, 96 time-history analyses were carried out to assess the effect of SSI and lateral resisting system on the PDAs design. Based on the parametric analyses, the response significantly increases as the soil flexibility increases for both type of lateral wind loads, particularly for flexural-type deformations. The results show a great effectiveness of PDAs in controlling across-wind peak displacements and both along-wind and across-wind RMS accelerations, on the contrary, PDAs were ineffective in controlling along-wind peak displacements on all soil types and different kind of lateral deformation. Generally speaking, the maximum possible value of the PDA mass efficiency index increases as the soil flexibility increases, on the contrary, it decreases as the non-dimensional lateral stiffness ratio of the building increases; therefore, there is a significant increase of the vibration control effectiveness of PDAs for lateral flexural-type deformations on soft soils.

• Wind and Structures
• /
• v.36 no.2
• /
• pp.91-103
• /
• 2023

Tuned liquid dampers (TLDs) are increasingly being used as efficient dynamic vibration absorbers to mitigate wind-induced vibration in super high-rise buildings. However, the damping characteristics of screens and the control effectiveness of actual structures must be investigated to improve the reliability of TLDs in engineering applications. In this study, a numerical TLD model is developed using computational fluid dynamics (CFD) and a simulation method for achieving the coupled vibration of the structure and TLD is proposed. The numerical results are verified using shaking table tests, and the effects of the solidity ratio and screen position on the TLD damping ratios are investigated. The TLD control effectiveness is obtained by simulating the wind-induced vibration response of a full-scale structure-TLD system to determine the optimal screen solidity ratio. The effects of the structural frequency, damping ratio, and wind load amplitude on the TLD performance are further analyzed. The TLD damping ratio increases nonlinearly with the solidity ratio, and it increases with the screens towards the tank center and then decreases slightly owing to the hydrodynamic interaction between screens. Full-scale coupled simulations demonstrated that the optimal TLD control effectiveness was achieved when the solidity ratio was 0.46. In addition, structural frequency shifts can significantly weaken the TLD performance. The control effectiveness decreases with an increase in the structural damping ratio, and is insensitive to the wind load amplitude within a certain range, implying that the TLD has a stable damping performance over a range of wind speed variations.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.5
• /
• pp.56-67
• /
• 1994

The installation methods of diesel engines in ships would be largely classified into two groups : one is the direct mounting system fixing engine directly into double bottom of the hull, and the other is the resilient mounting system having vibration absorbers between engine and ship body such as rubber plate to prevent shocks or vibration transmission. The direct mounting system is generally used for large-sized low speed diesel engines, because the resilient mounting system has difficulties in reducing the natural frequency of engine itself under normal speed. On the contrary, the resilient mounting system is often used for medium or high speed engines for marine propulsion and generator that have light weight and high revolution speed. Recently, it is even applied to engines having relatively low speed(300-400rpm) for fishing boats. Although many researches for the resilient mounting system have been carried out, many problems in applying these results directly to marine vessels because most of these have been used for automobiles. Up to now we have had to depend on the professional foreign company in design and the supply of parts for the resilient mounting system of marinediesel engines utterly. In preseut study, the exciting forces of engines effecting to resilient mounting were examined, and patterns of vibration and evaluation procedure for force transmission from resilient mounting to the body of hull were established. Also, these results were applied to the analysis of free and forced vibration for the rubber-type resilient mounting systems of marine diesel engines. Besides, after changing the various design parameters, such as locations, angles, dynamic characteristics and the number of resilient mountings, the influences on resilient mounting system were also examined.