• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.133-134
• /
• 2020

The equation of end bearing capacity is applied differently depending on the type of pile, construction method, and load characteristics considering the construction standards. The bearing capacity equation of the design standard is presented in various ways according to the design conditions such as construction method and ground condition, etc. but, It does not reflect the ground strength according to the SPT-N value of weathered rock. This study analyzed the trend of allowable tip bearing capacity by pile diameter through about 480 dynamic loading tests conducted for the construction/quality management of piles for the last 6 years since 2015. The equation for the ultimate end bearing capacity per unit area according to the SPT-N value is presented. The proposed formula of ultimate end bearing capacity per unit area can be applied in the range of 15,000kN/m2 to 30,000kN/m2. The proposed formula, which complements the existing formula, enables pile design and construction/quality management.

• 한국강구조학회 논문집
• /
• 제12권6호
• /
• pp.715-725
• /
• 2000

본 논문은 링크구성 설계를 통하여 결정된 하나의 이중링크 형식 수평인입 집 크레인에 대하여 작업위치에 따라 각 링크의 변위, 속도, 가속도 해석을 하고, 인입 가감속에 의한 관성력, 바람에 의한 풍하중, 크레인 자중 및 정격 권상하중 등이 크레인에 작용할 때 인입장치에 요구되는 정적 힘을 계산하였다. 모든 해석과정은 전산 프로그램으로 작성되었고, 프로그램의 신뢰성은 관련 범용 소프트웨어들의 해석 결과와 비교하여 검증하였다. 따라서, 본 논문에서 개발한 전산 프로그램은 이중링크 형식 수평인입 집 크레인의 설계 실무에 있어서 이동하중에 대한 인입궤적의 진폭 및 작업위치에 따라 인입장치에 요구되는 힘의 해석을 신속, 정확하게 처리할 수 있어 설계의 생산성 및 신뢰성 제고뿐만 아니라 기본설계 기술력의 확보 측면에서 그 의의가 있다.

• 한국태양에너지학회 논문집
• /
• 제36권6호
• /
• pp.1-12
• /
• 2016

A control algorithm for a 100 kW wind turbine is designed in this study. The wind turbine is operating as a variable speed variable pitch (VSVP) status. Also, this wind turbine is a permanent magnet synchronous generator (PMSG) Type. For the medium capacity wind turbine considered in this study, it was found that the optimum tip speed ratios to achieve the maximum power coefficients varied with wind speeds. Therefore a commercial blade element momentum theory and multi-body dynamics based program was implemented to consider the variation of aerodynamic coefficients with respect to Reynolds numbers and to find out the power and thrust coefficients with respect tip speed ratio and blade pitch angles. In the end a basic power controller was designed for below rated, transition and above rated regions, and a load reduction algorithm was designed to reduce tower vibration by the nacelle motion. As a result, damage equivalent Load (DEL) of tower fore-aft has been reduced by 32%. From dynamic simulations in the commercial program, the controller was found to work properly as designed. Experimental validation of the control algorithm will be done in the future.

• 한국지반공학회지:지반
• /
• 제14권5호
• /
• pp.163-172
• /
• 1998

말뚝의 지지력 거동을 연구하기 위하여 말뚝 제작시 다수의 변형률계를 설치한 2본의 말뚝들에 대하여 항타시에 그리고 항타후 소정의 시간이 경과된 시점에 동재하시험과 정재하시험을 몇 차례 수행하였다. 콘관입저항값 그리고 표준관입저항값과 말뚝의 단위 주면마찰력과의 관계를 규명하기 위해 재하시험전에 시험지반에 대하여 론관입시험과 표준관입시험도 실시하였다. 지지력과 두부침하량 관계를 살펴보면, 0.055D(D: 직경)의 두부침하량에서 전체지지력이 극한에 도달하였고, 이 때에 주면마찰력은 극한간에 도달했으나, 선단지지력은 계속 증가하는 것으로 나타났다. 말뚝의 지지력은 항타후 시간이 경과함에 따라 자연대수함수로 증가하였으며, 지지력 성분중 주면마찰력 성분이 항타한 후 40일 경과한 시점에 초기값의 4.6배 정도로 현저하게 증가하였다. 지지력 거동에 대한 시간경과의 영향을 보면, 시험말뚝들은 초기항타시에는 선단지지말뚝으로 거동하다가 시간이 경과하면서 주면마찰 말뚝으로 거동이 변화되었음을 관찰할 수 있었다. 단위 주면마찰력은, 토질분류에 따라 다르지만, 콘관입저항칼(q.)과 표준관입저항값(N)과 일정한 관계를 갖는 것으로 나타났으며, 관계상수는 현재 국내에서 사용하고 있는 간보다 큰 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제28권11호
• /
• pp.1776-1785
• /
• 2004

In this research, the relationships between static bimaterial constant and dynamic oscillation index are studied. It was certified that static bimaterial constant has the same form equation as the dynamic oscillation index. Bimaterial constant and oscillation index are increased with the increment of Young's modulus ratio and approached to the some value. Isochromatic fringe patterns are slanted to the left side with increment of bimaterial constants and oscillation index. Though patterns of stress components in above the crack surface are similar to each other, their magnitudes are different a little. In the ahead of crack tip, there are big differences in the isochromatic fringe patterns and their magnitudes. The influence of bimaterial with Young's modulus ratio is bigger in the propagation crack than in the stationary crack.

• 한국공작기계학회논문집
• /
• 제11권3호
• /
• pp.65-71
• /
• 2002

Friction welding has may merits such as energy efficiency, simple processing, etc. but it is difficult to obtain good welding at the welded interfaces and heat affected zone. It is discovered that stress singularity exists at the interferes and heat affected zone. The computer program based on boundary element method is utilized in this study. A mathematical model is implemented based on results from several experiments performed at and around the welded interfaces and heat affected zone of disimilar metals under static and dynamic loadings. This stay is to investigate the characteristics of the deformation and fracture behavior around interfaces for friction welded materials under static tensile load. Also, the stress distribution at the tip of crack is analyzed by using BU based on Kelvin's solution of 2-dimensional binding zone. The results of BEM are identical with those in case of considering interfaces of both heat affected zone. Also, stress singularity at the tip of interfaces appears when the elastic modulus ratio is 1.07.

• Geomechanics and Engineering
• /
• 제2권3호
• /
• pp.177-190
• /
• 2010

This paper presents the details of indigenous development of the piezovibrocone and calibration chamber. The developed cone has a cylindrical friction sleeve of $150cm^2$ surface area, capped with a $60^{\circ}$ apex angle conical tip of $15cm^2$ cross sectional area. It has a hydraulic shaker, coupled to the cone penetrometer with a linear displacement unit. The hydraulic shaker can produce cyclic load in different types of wave forms (sine, Hover sine, triangular, rectangular and external wave) at a range of frequency 1-10 Hz with maximum amplitude of 10 cm. The piezovibrocone can be driven at the standard rate of 2 cm/sec using a loading unit of 10 ton capacity. The calibration chamber is of size $2m{\times}2m{\times}2m$. The sides of the chamber and the top as well as the bottom portions are rigid. It has a provision to apply confining pressure (to a maximum value of $4kg/cm^2$) through the flexible rubber membrane inlined with the side walls of the calibration chamber. The preliminary static as well as dynamic cone penetration tests have been done sand in the calibration chamber. From the experimental results, an attempt has been made to classify the soil based on friction ratio ($f_R$) and the cone tip resistance ($q_c$).

• Structural Engineering and Mechanics
• /
• 제89권5호
• /
• pp.539-547
• /
• 2024

This study examines crack behavior within orthopedic cement utilized in total hip replacements through the finite element method. Its main goal is to compute stress intensity factors (SIF) near the crack tip. The analysis encompasses two load types, static and dynamic, applied to a crack starting from the interface between the cement and bone. Specifically, it investigates SIFs under mixed mode conditions during three activities: normal walking, climbing upstairs, and downstairs. The results highlight that a crack originating from a micro-interface under substantial loading can cause cement damage, leading to prosthetic loosening. Stress intensity factors in modes I, II, and III are influenced by the crack tip's orientation and location in the bone cement, with a 90° orientation yielding notably higher values across all three modes.

• Smart Structures and Systems
• /
• 제12권5호
• /
• pp.501-521
• /
• 2013

This paper is concerned with static and dynamic shape control of a laminated Bernoulli-Euler beam hosting a uniformly distributed array of resistively interconnected piezoelectric patches. We present an analytical one-dimensional model for a laminated piezoelectric beam with material discontinuities within the framework of Bernoulli-Euler and extent the model by a network of resistors which are connected to several piezoelectric patch actuators. The voltage of only one piezoelectric patch is prescribed: we answer the question how to design the interconnected resistive electric network in order to annihilate lateral vibrations of a cantilever. As a practical example, a cantilever with eight patch actuators under the influence of a tip-force is studied. It is found that the deflection at eight arbitrary points along the beam axis may be controlled independently, if the local action of the piezoelectric patches is equal in magnitude, but opposite in sign, to the external load. This is achieved by the proper design of the resistive network and a suitable choice of the input voltage signal. The validity of our method is exact in the static case for a Bernoulli-Euler beam, but it also gives satisfactory results at higher frequencies and for transient excitations. As long as a certain non-dimensional parameter, involving the number of the piezoelectric patches, the sum of the resistances in the electric network and the excitation frequency, is small, the proposed shape control method is approximately fulfilled for dynamic load excitations. We evaluate the feasibility of the proposed shape control method with a more refined model, by comparing the results of our one-dimensional calculations based on the extended Bernoulli-Euler equations to three-dimensional electromechanically coupled finite element results in ANSYS 12.0. The results with the simple Bernoulli-Euler model agree well with the three-dimensional finite element results.

• 한국유체기계학회 논문집
• /
• 제18권6호
• /
• pp.63-70
• /
• 2015

This paper proposes a novel airfoil named "KA2" for the blade of the wind turbine systems. Dynamic loads characteristics are analyzed and compared using aerodynamic data of ten airfoils including the proposed airfoil. The blade is divided into the sixteen elements in the longitudinal direction of the blade for applying the Blade Element Method Theory (BEMT) method, and in each element, torque, thrust, and pitching moment are calculated using turbulent time varying wind speed and aerodynamic data of each wing. Additionally, each force and torque is accumulated in the whole region of the blade for the estimation of representative values. The magnitude of such forces is comparatively analyzed for different airfoils. The angle of attack is constant below the rated wind speed due to the fact that the tip speed ratio is kept at the constant value, and it increases in the region of over rated wind speed as the tip speed ratio decreasing with constant rated rpm and increasing wind speed. Such increase in the angle of attack causes the changes of the force acting on the airfoil with different characteristics of lift and drag in the stall region of each different airfoil. Even though the mean wind speed is in the rated speed in a given time, because of the turbulence, it has either the over rated or under rated speed most of the time. Furthermore, the dynamic properties of each force are analyzed in this rated wind speed in order to objectively understand the dynamic properties of the blades which are designed based on the different airfoils. These dynamic properties are also compared by the standard deviation of time varying characteristics. Moreover, the output characteristics of the wind turbine are investigated with different airfoils and wind speeds. Based on these investigations, it was revealed that the proposed airfoil (KA2) is well applicable to the blade with passive pitch control system.