• 한국군사과학기술학회지
• /
• 제14권2호
• /
• pp.264-270
• /
• 2011

This paper focuses on possibility to design and fabrication new combination of bullet core to substitute current toxic material of heavy metal such as lead by environment-friendly ones. The core is designed as dual structure to manipulate the core center of gravity easily by combining materials, which of basis is tungsten of low cost and easily acquired. Those combinations are W-M series such as W-Cu, W-Sn, W-Cu-Sn, and W-Cu-Ni to target the density of lead, $11.34g/cm^3$ through powder-metallurgy. Out of four, combination of W-Cu-Ni shows the highest compression density of 96% and is confirmed as the most suitable substitution for lead due to the excellent property of matter and sintering. All combination samples is simulated on the PRODAS software for designing and structure analysis by adjusting the center of gravity of dual core samples forward and backward. The simulations confirm the similarity of current bullet core with respect to properties of mass, aero dynamics, and flying stability.

• 전기전자학회논문지
• /
• 제14권2호
• /
• pp.69-75
• /
• 2010

3D 그래픽 처리 과정은 크게 지오메트리 단계와 렌더링 단계로 구분된다. 본 논문에서는 듀얼페이즈 멀티코어 GP-GPU에서 지오메트리 처리를 가속화시키기 위한 방법을 제안한다. GP-GPU의 SIMD, 듀얼페이즈 구조를 이용한 병렬적 데이터 처리와 메모리 프리패치를 이용하여, 지오메트리 처리를 가속화 시킬 수 있었으며, 모든 기능을 사용할 시 19%의 성능 향상을 나타내었다.

• 한국전자통신학회논문지
• /
• 제10권5호
• /
• pp.539-548
• /
• 2015

본 논문에서는 프로세서별 서로 다른 버스에 서로 다른 운영체제를 갖는 멀티코어 시스템에서 공유 메모리 기능을 구현하고, 임베디드 리눅스 시스템을 통하여 두 프로세서 사이에서 공유 메모리 기능을 실험하였다. 듀얼 버스 구조에서 공유 메모리 구현을 위해 메모리 컨트롤러를 이용하였으며, 리스트 자료구조를 통하여 공유 메모리 세그먼트를 관리한다. AMP 멀티 코어 실험을 위하여 2개의 프로세서 코어에 리눅스 운영체제를 탑재하도록 하였다. 그리고 공유 메모리 테스트를 위하여 구현된 커널 모듈을 이용하여 공유 메모리 생성 및 이용이 가능함을 확인 하였다.

• 전력전자학회논문지
• /
• 제21권6호
• /
• pp.473-480
• /
• 2016

This study proposes a performance improvement for parallel-connected thyristor dual converters using a circulating current with an unbalanced parallel operation compensator. The proposed control method determines a variable reference value for the voltage PI controller according to voltage error at firing angle control applied to a difference current control. This method uses circulating current control to maintain a stable voltage and excellent current response during parallel operation. The effectiveness of the proposed control is verified with a simulation and an experiment based on the comparison of the performance of the proposed control method with other conventional methods.

• 한국소음진동공학회논문집
• /
• 제27권2호
• /
• pp.175-181
• /
• 2017

In the present work, to achieve high braking performance with restricted size, characteristics of magneto-rheological (MR) fluid brake is numerically investigated considering different magnetic core shapes. As a first step, structural configuration of the MR brakes are proposed with four different magnetic core shapes, such as single flat, single inclined, dual flat and dual inclined. To estimate braking performance of the proposed MR brakes, electromagnetic analysis is carried out and the results of magnetic field intensity distribution are observed. Based on the electromagnetic analysis results, braking torque of the MR brake is estimated according to magnitude of current input and results are discussed. It is observed that enhanced braking torque can be achieved by adopting the modified magnetic core shape under limited small size of the MR brake.

• 한국기계가공학회지
• /
• 제21권1호
• /
• pp.8-14
• /
• 2022

A computer simulation was performed to investigate the heat source distribution and temperature distribution of a laser having multiple characteristics. To simulate the actual size of a welding specimen, the temperature distributions at 0 s, 1 s, and 2 s were analyzed by increasing the domain size to 50 mm in length and 25 mm in width in a material of the same thickness. As indicated by the results, because of the characteristics of metals with high thermal conductivity, the temperature at the welding center line and the temperature distribution at the offset position were not significant. When the core part was cooled by irradiating with a laser, it cooled at a rate of up to 500 ℃/s. In contrast, when the laser was irradiated to the ring part, the cooling proceeded at a rate of over 1800 ℃/s. Comparing the relative numerical values rather than the absolute values, it was found that the cooling rate was approximately 3.6 times faster when the laser was irradiated through the ring than when the laser was irradiated through the core. As a result of irradiating with the same heat source (at 100 W) into the core, ring, and ring + core, it was confirmed that the highest temperature was irradiated to the ring part and the lowest temperature was irradiated to the core part.

• Current Optics and Photonics
• /
• 제3권4호
• /
• pp.304-310
• /
• 2019

In this paper, a microstructured, hexagonal-shaped dual-core photonic crystal fiber (PCF) is proposed. The proposed structure has specific optical properties to obtain high birefringence and short coupling length, for different values of structural parameters varied over a wide range of wavelength. The properties are analyzed using a solid core of silica material. The proposed structure is implemented as a polarization splitter with splitting length of 1.9 mm and a splitting ratio of -34.988 dB, at a wavelength of 1550 nm. The obtained bandwidth in one band gap of about 81 nm. The numerical analysis ensures that the performance of the proposed polarization splitter is better than that of existing ones.

• 한국광학회지
• /
• 제17권1호
• /
• pp.94-98
• /
• 2006

본 논문에서는 듀얼 코어 광섬유 콜리메이터(dual-core fiber collimator)와 멤브레인형 마이크로미러를 이용한 광마이크로폰을 제안하고 구현하였다. 콜리메이터와 미러는 각각 광헤드(optical head)와 반사형 진동판으로서 사용된다. 특히, 미러 진동판은 얇은 실리콘 바(bar)에 의해 프레임에 연결되어 있어서 인가된 음압에 따라 자유롭게 움직인다. 두 개의 콜리메이터가 집적된 광헤드는 음압을 감지하고 변조하는데 사용되는 광을 공급하고 받는 역할을 한다. 이 콜리메이터 광헤드를 사용함으로써 진동판과의 초기 정렬시 기존의 광섬유를 이용한 경우에 비해 허용 오차가 클 뿐만 아니라 전체적으로 광마이크로폰의 구조도 간단해졌다. 본 논문에서는 광헤드와 진동판 사이의 거 리를 변화시켜 가면서 응답 특성을 측정하여 선형성과 민감도가 최대인 지점을 동작점으로 결정하였다. 음성신호의 주파수를 변화시켜 가면서 광마이크로폰의 출력을 측정하여 얻은 주파수 대역폭은 약 $\pm$5 dB 이하 출력 변화에 대해 약 3 kHz였다.

• 대한수학회지
• /
• 제34권2호
• /
• pp.469-481
• /
• 1997

In this paper we consider TU-cooperative games in the form of characteristic function. We notice that if one uses the necessary and sufficient condition for the core to be not empty in a dual form, it may be used for selecting the final outcome in the core. Using the linear programming approach for constructing the subcore, which is a subset of the core, we represent it in a simple form. We consider reduced games due to Davis-Mashler, Moulin and Funaki and formulate the sufficient conditions for the subcore to be S-consistent.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 학술대회 논문집
• /
• pp.43-46
• /
• 2003

The dc reactor type high-Tc superconducting fault current limiter(SFCL) is composed of three parts, a power converter, a magnetic core reactor(MCR) and a dc reactor. This study concerned with the power converter of the DC reactor type high-Tc SFCL. The rectifying devices which power converter of 6.6kV/200A SFCL consists of have to endure high voltage. We propose the dual mode power converter to reduce the voltage which each rectifying device endures. In the single phase the experiment and simulation of dual mode power converter and the simulation of power converter with one bridge rectifier are performed. The current of each system with different power converter has a same tendency and the voltage which rectifying device of dual mode power converter endures is reduced in half by comparison with that of power converter with one bridge rectifier. We found dual mode power converter can be applied to SFCL.