• Journal of Korean Society on Water Environment
• /
• v.36 no.6
• /
• pp.489-499
• /
• 2020

Effective science-based management of the basin water resources requires an understanding of the characteristics of the streams, such as the baseflow discharge. In this study, the base flow was estimated in the two watersheds with the least artificial factors among the Nakdong River watersheds, as determined using the chemical hydrograph separation technique. The 16-year (2004-2019) discontinuous observed stream flow and electrical conductivity data in the Total Maximum Daily Load (TMDL) monitoring network were extended to continuous daily data using the TANK model and the 7-parameter log-linear model combined with the minimum variance unbiased estimator. The annual base flows at the upper Namgang Dam basin and the upper Nakdong River basin were both analyzed to be about 56% of the total annual flow. The monthly base flow ratio showed a high monthly deviation, as it was found to be higher than 0.9 in the dry season and about 0.46 in the rainy season. This is in line with the prevailing common sense notion that in winter, most of the stream flow is base flow, due to the characteristics of the dry season winter in Korea. It is expected that the chemical-based hydrological separation technique involving TANK and the 7-parameter log-linear models used in this study can help quantify the base flow required for systematic watershed water environment management.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.2
• /
• pp.35-40
• /
• 2014

Wire drawing is aplastic deformation process that produces a wire with a desired diameter by pulling the end of the wire through a die. During the cold wire drawing process, the temperature between the wire and the die bearing is increased. This temperature increase causesenergy consumption increase, bad wire quality, and decreased die life. To reduce friction and avoid high temperature between the wire and the die in the cold wire drawing process, a dry lubricant with soap particles is used. It is not possible to reused the lubricant onceiron oxide is attached to the soap particlesat high pressure die. In this study, recycling technologies for wasted soap particles with processes of crushing, separation, and screening are developed. From the evaluation, the recycling efficiency was found to be 86.97%.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.4 s.142
• /
• pp.322-329
• /
• 2005

Viscous flows behind transom stern are analyzed based on CFD simulation results. Stern wave pattern is often complicated due to the abrupt change of stern surface curvature and flow separation at transom. When a ship advances at high speed, whole transom stern is exposed out of water, resulting in the so-called 'dry transom'. However, in the moderate speed regime, stern wave development in conjunction of flow separation makes unstable wavy surface partially covering transom surface, i.e., the so-called 'wetted transom'. Transom wave formation is usually affecting the resistance characteristics of a ship, since the pressure contribution on transom surface as well as the wave-making resistance is changed. Flow modeling for 'wetted transom' is difficult, while the 'dry transom modeling' is often applied for the high-speed vessels. In the present study CFD results from the RANS equation solver using a finite volume method with level-set treatment are utilized to assess the topology of transom flow pattern for a destroyer model (DTMB5415) and a container ship (KCS). It is found that transom flow patterns are quite different for the two ships, in conformity to the shape of submerged transom. Furthermore, the existence of free surface seems to after the flow topology in case of KCS.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.2
• /
• pp.150-158
• /
• 2005

Added ratio of 8YSZ powder and organic compounds (solvent, plasticizer, dispersant, binder) properly. It manufactured electrolysis membrane by wet process that make slurry and dry process that do not use organic compounds. In the case of wet process, harmony combination and method of organic compound are an importance element in slurry manufacture. This slurry did calcine at temperature of 140$^{\circ}C$ in Furnace and manufactured electrolyte disk by Dry pressing method. Like this, manufacturing disk sintered at temperature of $1300^{\circ}C,\;1400^{\circ},\;1500^{\circ}C$ in Furnace and completed electrolysis membrane. Confirmed change of crystal structure and decision form through analysis of density, SEM, XRD according to change of sintering temperature, and considered relation with ion conductivity.

• Child Health Nursing Research
• /
• v.6 no.2
• /
• pp.158-166
• /
• 2000

The purpose of this study was to confirm the efficient umbilical cord care of healthy newborns in nursery. In order to determine the efficient care, the time of umbilical cord separation and the skin condition of periumbilical area were evaluated. The data were collected in sample of 529 normal, healthy newborns of C hospital in Seoul, from September 1st, 1999 to January 16th, 2000. The babies were randomly selected and allocated into four groups-alcohol swab/tub bath, alcohol swab/partial bath, natural dry/tub bath, natural dry/partial bath- by the methods of care. The mothers of babies were also surveyed by questionnaire about general characteristics. The data were analyzed by SAS program. The results of this study were as follows : 1. The average gestation period of newborns was 39+3 weeks. The average birth weight was 3.27Kg. In gender of babies, boys were 51.7% and girls were 48.3%. The 65% of newborns were born normal vaginal delivery, 35% were C-section. The feeding methods were 55.3% of the babies fed by mixed type, 22.9% by breast, and 21.8% by bottle. There was no significance among four groups by general characteristics. 2. The average time of umbilical cord separation was 8.27 days(SD=2.3). The time was no difference significantly among four groups(F=1.68, P=0.17). 3. The prevalence of the umbilical care complication did not show differences among four groups( 2=3.93, P=0.27). In conclusion, Nurses have preferred the traditional alcohol swab/partial bath method in care of newborns. But there was no difference among the ways to take care of umbilicus according to this study. The way to naturally is more efficient due to reduce the time and expense in umbilical care for normal babies of nursery. This also matched the change in approach to healthy population from intervention to nonintervention way. This could be suggested in education for normal and healthy babies care at home and nursery as a useful way. Endly, the further study about bacterial colony nda infection rate at umbilicus by ways of care is needed.

• Resources Recycling
• /
• v.11 no.1
• /
• pp.9-18
• /
• 2002

Printed wiring boards(PWBs) of the obsolete computers are composed of various organic and inorganic compounds as well as metals and alloys. As convinced that the valuable metals obtained from the PWBs are effectively utilized as secondary resources when recovered by economical methods, in this study, an investigation for characterizing the physical separation techniques is conducted. For the recovery of them, the sockets and chips dismantled from PWBs by scraping and residual resin boards are subjected to the appropriate separation processes according to the physical properties of each part. In the case of crushed socket scraps size ranged from -2.36 mm to +1.18 mm, approximately 97 wt% of the product obtained by magnetic separation consists of metallic compounds. In the case of chip scraps, 97% of Fe-Ni alloy and 95% of Cu metal are recovered by the combined process of air classification and dry magnetic separation in the size range from -2.36 mm to +0.15 mm. Ball milling is adopted in order to improve the removal efficiency of the thin-printed metallic materials on the residual resin boards and approximately 77% of Cu metal is recovered by zigzag separation after ball milling.

• Mineral and Industry
• /
• v.28
• /
• pp.1-13
• /
• 2015

In this study, it was carried out separation process research and development to be able to produce high-grade tungsten concentrate form tungsten taken form Mongolia. In order to reduce treatment cost and increase separation efficiency the jig separation at first was applied for recovering the concentrate. Which reground would make the degree of liberation increase. Which was treated by shaking table to reject the gangue minerals from the first concentrate. Because the heavier product contains not only ferberite but also cassiterite, the product was treated by further dry magnetic separation to obtain the ferberite concentrate. Finally, the high-grade ferberite concentrate of 67.63% $WO_3$ could be obtained with recovery of 86.07% through the separation process developed in this study.

• Earthquakes and Structures
• /
• v.12 no.6
• /
• pp.619-628
• /
• 2017

The intent of this paper is to investigate the propagation of Love waves in a dry sandy medium sandwiched between fiber-reinforced layer and prestressed porous half-space. Separate displacement components have been deduced in order to characterize the dynamics of individual materials. Using suitable boundary conditions, the frequency equation has been derived by means of separation of variables which reveals the significant role of reinforcement parameters, sandiness, thickness of layers, porosity and prestress on the wave propagation. The phase velocity of the Love wave has been discussed in accordance with its typical cases. In both cases when fiber-reinforced and dry sandy media are absent, the derived equation of Love type wave coincides with the classical Love wave equation. Numerical computations have been performed in order to graphically illustrate the dependencies of different parameters on phase velocity of Love waves. It is observed that the phase velocity decreases with the increase of parameters pertaining to reinforcement and prestress. The results have certain potential applications in earthquake seismology and civil engineering.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.312-319
• /
• 2017

For high value-added applications of natural blue diatomite, the physical refining process and synthesis of SiC from refined diatomite were investigated. Approximately 30 percent Fe ($Fe_2O_3$) in raw blue diatomite was removed by a particle sieve separation process; the Fe composition for 325 mesh down powder was approximately 2 percent. Although a wet and/or dry magnetic separation process had some influence on the separation and/or refining of Fe composition, the Fe composition in the non-magnetic by-product was approximately 2 percent. Water leaching separation was effective in removing the Fe composition; approximately 40 percent of the Fe in raw blue diatomite was removed. The synthesis of ${\beta}$-SiC by a carbothermal reduction of the $SiO_2$ in the refined diatomite using carbon (graphite, carbon black), the effects of an acid-treatment on removing the Fe, and the specific surface area for the synthesized powder were also investigated. The impurities were mostly eliminated and the specific surface area was increased to $52.5m^2/g$.

• Membrane Journal
• /
• v.10 no.3
• /
• pp.130-138
• /
• 2000

Polyethersulfone (PES) asymmetric membranes for gas separation were prepared by dry/wet phase inversion method and their separation properties for CO$_2$ and N$_2$ gases were investigated. The effects of important variables such as composition of casting solution and evaporation time in preparation of asymmetric gas membrane on membrane morphology and the separation properties were analyzed and the optimum condition of membrane preparation was established. To compensate the defects like pinholes existed on skin layer of the membrane prepared, the membranes were coated with silicone resin. By comparing separation properties after coating with those before coating, we found that the coating of silicone resin was effective to enhance the separation properties. The casting solution mainly used in this study consisted of PES, N-methyl-2-pyrrolidone, acetone, ethanol and distilled water was used as coagulation agent. It was shown that the selectivity for CO$_2$/N$_2$ was getting higher but the permeability decreases, as the contents of PES and volatile organic solvent and evaporation time increased. The selectivity for CO$_2$/N$_2$ and permeability of CO$_2$ of the membrane prepared under the optimum condition were found to be 61 and 21 GPU, respectively.