• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.175-180
• /
• 1999

The heating system of korea apartment house is called Ondol. The surface finishing mortar of this floor system typically used the cement based mortar, where the surface finishing mortar easily appears the crack. To order to crack control, the cement that added expansive additive used to reducing dry-shrinkage. For the surface finishing mortar, the types of shrinkage is known as plastic shrinkage, dry-shrinkage and autogenous This experimental study is to investigate the difference on dry-shrinkage of the cement that added expansive additives and OPC. The test method is varied the ration of water/cement (W/C) and the ratio of sand/cement(S/C). For OPC, The increase of the ratio of S/C is reduced dry-shirnkage but for the cement that added expansive additives, the increase of the ratio of S/C is augmented dry-shrinkage For OPC, The increase of the ratio of W/C is augmented dry-shrinkage but for the cement that added expensive, the increased of the ratio of W/C is reduced dry-shrinkage.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.3
• /
• pp.5-14
• /
• 2023

The dry unit weight of the soil can be obtained by measuring the weight of the oven dried soil. According to the Korean Industrial Standards (KS F), oven dried soil at 110±5℃ continuously increases in weight when exposed to air. However, there is no regulation on the weight measurement time of oven dried soil, making it difficult to accurately measure the dry weight. In this study, a method to easily determine the dry weight was presented through the analysis of the weight singularity that appears during weight measurement. The weight singularity represents the smallest value among the measured weights, and is the weight at which the effect of moisture absorption in the air of the sample is minimized. In the course of the experiment, a container was selected using a statistical analysis method, and a photograph of the soil samples were presented using an optical microscope. In addition, the temperature of the weight singularity was measured using a non-contact infrared thermometer. As a result of analyzing the weight singularity of six types of soil, including Jumunjin sand, Naeseong stream sand, Yecheon weathered granite soil, Jeju sand, Sabkha sand, and Ulleung sand, the weight singularity of oven dried sample appeared between 8 and 27 seconds after weight measurement, and the temperature ranged from 103.4 to 108.13℃. The weight decrease rate of the singularity was 0.0066 to 0.0085% depending on the soil samples.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5C
• /
• pp.207-215
• /
• 2009

Cemented soils or concrete are usually cured under moisture conditions and their strength increases with curing time. An insufficient supply of water to cemented soils can contribute to hydration process during curing, which results in the variation of bonding strength of cemented soils. In this study, by the consideration of in situ water supply conditions, cemented sand with cement ratio less than 20% is prepared by air dry, wrapped, moisture, and underwater conditions. A series of unconfined compression tests are carried out to evaluate the effect of curing conditions on the strength of cemented soils. The strength of air dry curing specimen is higher than those of moisture and wrapped cured specimens when cement ratio is less than 10%, whereas it is lower when cement ratio is greater than 10%. Regardless of cement ratio, air dry cured specimens are stronger than underwater cured specimens. A strength increase ratio with cement ratio is calculated based on the strength of 4% cemented specimen. The strength increase ratio of air dry cured specimen is lowest and that of wrapped, moisture, and underwater cured ones increased by square. Strength of air dry cured specimen drops to maximum 30% after wetting when cement ratio is low. However, regardless of cement ratio, strength of moisture and wrapped specimens drops to an average 10% after wetting. The results of this study can predict the strength variation of cemented sand depending on water supply conditions and wetting in the field, which can guarantee the safety of geotechnical structures such as dam.

• Korean Journal of Environmental Agriculture
• /
• v.5 no.2
• /
• pp.135-140
• /
• 1986

K-bentonite was made by ion exchange reaction in $K^{\ast}$ ion saturated aqueous solution. K-bentonite had a slow releasing effect in different soils such as sand, sandy loam and clayey loam, but the effect was the best in sand. The growth of radish and lettuce was better in the plot fertilized with K-bentonite than with KCl in sand culture in field condition. There was no effects on the growth of radish grown in pot in glass house. Vitamin C, nitrate content, thiocyanate ion content and dry weight of radish were not affected by K-bentonite and KCl in both pot and field culture. The commercial production of K-bentonite was discussed.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.2 no.3
• /
• pp.18-24
• /
• 1999

This study was aimed to develope appropriate soil media for the growth of Rhododendron hybrid $J_{ASANHONG}$ on the artificial ground five types of soil media was tested such as "sandy loam-general soil (T1)", "vermiculite-artificial soil (T5)", "sandy loam 50% + vermiculite 30% + sand 20% (improved of soil 2-T2)", "sandy loam 50% + carbonized rice hust 30% + sand 20% (improved of soil 3-T3)", "sandy loam 50% + humus sawdust 30% + sand 20% (improved of soil 4-T4)". The result of the research are as follows. 1. Among the type of soil media, the sandy loam(T1) soil type gave the worst effects on growth of above ground parts(height, No. of leaf, width of leaf, No. of flowering, dry weight of upper parts) and under ground parts(dry weight of roots). 2. Vermiculite(T5) showed the highest root growth(dry weight of roots). it seemed to be caused high saturated hydraulic conductivity and porosity. As a result, there is much available space for enabling the root spreads. 3. "sandy loam 50% + vermiculite 30% + sand 20%(improved of soil 2-T2)", "sandy loam 50% + carbonized rice hust 30% + sand 20%(improved of soil 3-T3)" showed good effects on growth of above ground parts and under ground parts compared with sandy 10am(T1) 4. "sandy loam 50% + humus sawdust 30% + sand 20% + (improved of soil 4-T4)" showed the highest effects on growth of above ground parts.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.4
• /
• pp.113-121
• /
• 2011

River sand has generally used for the backfill material of underground power cables. The thermal resistivity of it has $150^{\circ}C$-cm/Watt in wet condition and more than double in dry condition. The final goal of this study is to find the backfill material which has a small change in thermal resistivity with various water contents, for example thermal resistivity is $50^{\circ}C$-cm/Watt and $100^{\circ}C$-cm/Watt in wet and dry conditions respectively. In this study it is presented that the comparison of thermal resistivity using stone powder, crush rock, weathered granite soil and Jumunjin sand as well as river sand in the needle method regarding water content, dry unit weight and particle size distribution. As a result, the thermal resistivity of a material is minimized when they have maximum dry unit weight at optimum moisture content and maximum density by appropriately mixing materials for particle size distribution. Therefore thermal resistivity characteristics should be considered two factors: one is the difference between natural dry condition and dry state after optimum moisture content, and the other is the difference between unit weight of raw material and maximum dry density.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.38-48
• /
• 1998

To apply the high chromium white cast irons for sliding parts of construction equipments, the wear characteristics of these alloys which have three kinds of microstructure(hypoeutectic, near-eutectic, hypereutectic) were investigated by dry sand/rubber wheel tester. Also, the effect of heat treatment was investigated for the same alloys. As result of the test, heat treatment have no effect on the wear characteristics. And, hypereutectic composition alloy has the highest wear resistance against SiO$_2$. Also after test, cracking was observed in eutectic and primary carbides of all materials tested. This phenomenon was important factor in the wear resistance.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.827-830
• /
• 2008

In this study, large triaxia mpression tests of sand-gravel soils were carry out to clarify the influence of fines on shear strength characteries. Two soil specimens with/without fines that is used for construction material of dam were prepared. One was reproduced with wide range of grain size and the other was removed fines below 2mm from the one. The compaction tests proposed by our center were performed to obtain relative density of the specimens, and then each specimen was adjusted two dry density. The large triaxial compression tests were carry out under CD condition. Based on the results, the sand-gravel soils with low fines content has no effect on shear strength characteries.

• Journal of Korea Foundry Society
• /
• v.22 no.3
• /
• pp.121-129
• /
• 2002

According to the investigation of waste $CO_2$ molding sand in the 15 steel foundries in Busan and Gyeong area, about 1 ton of waste $CO_2$ molding sand per ton of steel castings production was produced In order to reduce amount of $Na_2O$, Loss of Boiling (L.O.B), Loss of Ignition (L.O.I), Conductivity and PH which are present in the waste $CO_2$ molding sand below the reclamation effect, more than 50% of elimination for reclamation was required. It was found that the waste $CO_2$ molding sand does not contain a harmful component designated by industrial waste materials. Reclamation of the waste $CO_2$ molding sand was practically achieved by an abrasive-dry reclamation process. According to bench time of the sodium silicate-bonded $CO_2$ molding sand, reduction of compressive strength and surface stability index(S.S.I) become slowdown. Therefore, the reclaimed sand could be allowed the reuse of molding sand in $CO_2$ molding process including core sand.

• Geomechanics and Engineering
• /
• v.28 no.6
• /
• pp.547-557
• /
• 2022

Dune sands are poorly graded collapsible soils lacking fines. This experimental study explored the technical feasibility of sustainable invigoration of fine waste materials to improve the geotechnical properties of dune sand. The fine waste considered in this study is fine marble waste. The fine waste powder was mixed with dune sand at different contents (5, 10,15, 20, 25, 50%), where the gradation, void ratio, compaction, and shear strength characteristics were assessed for each fine marble waste -dune sand blend. The geotechnical properties of the dune sand-fine marble waste mix delineated in this study reveal the enhancement in compaction and gradation characteristics of dune sand. According to the results, the binary mixture of dune sand with 20% of fine marble waste gives the highest maximum dry density and results in shear strength improvement. In addition, a numerical study is conducted for the practical application of the binary mix in the field and tested for an isolated shallow foundation. The elemental analysis of the fine marble waste confirms that the material is non-contaminated and can be employed for engineering applications. Furthermore, the numerical study elucidated that the shallow surface replacement of the site with the dune sand mixed with 20% fine marble waste gives optimal performance in terms of stress generation and settlement behavior of an isolated footing. For a sustainable mechanical performance of the fine marble waste mixed sand, an optimum dose of 20% fine marble waste is recommended, and some correlations are proposed. Thus, for improving dune sand's geotechnical characteristics, the addition of fine marble waste to the dune sand is an environment-friendly solution.