• 한국기계가공학회지
• /
• 제13권2호
• /
• pp.35-40
• /
• 2014

Wire drawing is aplastic deformation process that produces a wire with a desired diameter by pulling the end of the wire through a die. During the cold wire drawing process, the temperature between the wire and the die bearing is increased. This temperature increase causesenergy consumption increase, bad wire quality, and decreased die life. To reduce friction and avoid high temperature between the wire and the die in the cold wire drawing process, a dry lubricant with soap particles is used. It is not possible to reused the lubricant onceiron oxide is attached to the soap particlesat high pressure die. In this study, recycling technologies for wasted soap particles with processes of crushing, separation, and screening are developed. From the evaluation, the recycling efficiency was found to be 86.97%.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.436-439
• /
• 2008

It has been known that the value of soil resistance drops when a high impulse curennt is injected into a grounding electrode. In this paper, impulse generator is used to investigate the dry soil and wet soil characteristics in cylinderical test cell. The impulse resistances and breakdown characteristics were discussed based on its voltage and current traces. As a result, sand resistances are decreased with increasing the applied currents. It was thought that a decrease in resistance of dry sand with increasing current is due to both thermal and ionization processes. On the other hand, in case there is no water presence in the soil, the reduction in resistance as the currents are of dry sand increased is mainly due to the ionization process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.17-19
• /
• 2004

The electrical properties of gate oxides grown in two different processes, which are in 10% nitrous oxide($N_2O$) and in dry oxygen, have been experimentally investigated and compared. It has been observed that the $SiC-SiO_2$ interface-trap density(Dit) measured in nitrided gate oxide has been tremendously reduced, compared to the density obtained from gate oxide grown in dry oxygen. The beneficial effects of nitridation on gate oxides also have been demonstrated in the values of total near interface-trap density and of forward-bias breakdown field. The reasons of these improvements have been explained.

• Nuclear Engineering and Technology
• /
• 제56권3호
• /
• pp.824-831
• /
• 2024

In order to investigate the occurring processes during long-term dry storage of spent fuel assemblies, a joined project called SPIZWURZ, between the Karlsruhe Institute of Technology and the Gesellschaft für Anlagen-und Reaktorsicherheit (GRS), was started. Aim of the SPIZWURZ project is the determination and quantification of the influence of texture and elastic strain on diffusion and solubility of hydrogen in three different zirconium alloys used in western Europe during a long-term cooling transient (1 K/d) starting at 400 ℃. The strain in the cladding of an irradiated spent fuel rod shall be measured. Models predicting the formation of radial oriented hydrides will be validated, improved, and implemented in the GRS fuel rod performance code TESPA-ROD. This paper describes the SPIZWURZ project and already obtained first results.

• 한국초지조사료학회지
• /
• 제18권4호
• /
• pp.291-302
• /
• 1998

식물생장 조절제 Uniconazole-P의 처리가 초지조건에서 목초의 생육억제와 종자생산에 미치는 영향을 검토하였다. 초종은 화본과 목초 2초종(orchardgrass와 timothy)과 두과목초 2초종(red clover와 alfalfa)을 공시하였고, Uniconazole-P의 처리농도는 대조구, 20ppm구, 40ppm구의 3처리로 하여, 화본과 목초는 유수분화기에, 두과목초는 개화시기(開花始期)에서 엽면산포하였다. 본 실험에서 얻어진 결과를 요약하면 다음과 같다. 1. Uniconazole-P의 처리효과는 처리농도, 초종 및 생육단계에 따라서 차이가 인정되었다. 2. Uniconazole-P의 처리는 출수초기의 화본과 목초에서 초장과 간장이 단축되었고, 수중과 엽록소 함량을 증가시켰다. 3. Uniconazole-P의 처리는 종자 결실기의 orchardgrass에서 수수, 1경중, 수중, 1수중 및 종자중을 증가시켰고, timothy에서는 초장의 단축과 수수, 1수중, 수중, 종자중 및 수확지수를 증가시켰다. 4. Uniconazole-P의 처리는 개화초기의 red clover와 alfalfa 2초종 모두 초장과 총절간장을 단축시켰지만, 총분지장과 엽록소 함량을 증가시켰다. 특히 red clover에서는 화수와 화중의 증가가 현저하였다. 5. Uniconazole-P의 처리는 종자 결실기의 red clover에서 초장을 단축시켰고, 화중과 종자중을 증가시켰으며, alfalfa에서는 초장을 단축시키고 화중, 종자중 및 수확지수를 증가시켰다. 6. Uniconazole-P의 처리에 의한 화본과 목초의 종자 생산과정은 1) 출수초기에서 초장과 간장의 단축, 2) 출수초기와 종자 결실기에서 수수와 l수중의 증가, 3) 종자 결실기에서 단위면적당 수중과 종자중의 증가 및 수확지수의 증가로 설명할 수 있다. 7. Uniconazole-P의 처리에 의한 두과목초의 종자 생산과정은 1) 개화초기에서 초장과 총절간장의 단축과 분지수와 총분지장의 증가, 2) 개화초기와 종자 결실기에서 화수와 화중의 증가, 3) 종자 결실 기에서 종자중과 수확지수의 증가로 설명할 수 있다.

• 급식외식위생학회지
• /
• 제3권1호
• /
• pp.8-18
• /
• 2022

Dry-aging is one of the traditional aging processes, especially for beef. This aging process is being popular, because it produces unique brown/roasted flavor and texture that consumers prefer. However, as it is exposed to outside without packaging food safety concerns have been raised. The objective of this study was to investigate the presence of total aerobic bacteria (TAB) and pathogenic bacteria in manufacturing environment and suggest the safety management plan for the production of dry-aged meat. Surface samples from 66 environmental and 6 beef carcass samples were collected. According to the monitoring results, the contamination levels of TAB were in the order of shelves (5.4±1.1 Log CFU/cm²), cotton gloves (2.9±0.2 Log CFU/cm²), and door knobs (2.8±0.4 Log CFU/cm²) in the dry-aging room. In the door knobs, the level of mold was higher than that of yeast. These results indicate that the mold spores may be cross-contaminated with environmental factors inside the aging room. The risk factors that may occur during the manufacturing process were presented and possibility of risk was determined. From the aspect of microbiology, aging and trimming steps were determined as the critical control points. The temperature of the aging room should be maintained below 10℃ and the humidity below 75-85%. Based on the monitoring and the risk assessment of the dry-aging process, we prepared the safety management plan for the production of dry-aged meat, and it should be useful in improving the food safety of dry-aged meat.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2007년도 추계학술발표회
• /
• pp.129-130
• /
• 2007

• 공업화학
• /
• 제31권1호
• /
• pp.1-6
• /
• 2020

바이오가스를 이용한 수소 제조는 주요한 에너지 및 환경 관련 이슈들을 동시에 해결할 수 있다는 장점으로 꾸준히 주목받아 왔다. 바이오가스 정제를 통해 얻은 바이오메탄 수증기개질은 천연가스 개질을 대체할 수 있는 좋은 현실적인 대안이다. 하지만, 경제성과 환경 유해성을 모두 고려한다면 바이오가스를 직접 개질반응에 활용하는 바이오가스 수증기 개질 및 건식 개질을 활용한 수소 제조가 보다 효과적이라 평가된다. 본 논문에서는 바이오가스 기반 추출수소 제조 관련 최근의 기술 이슈 및 개발 동향을 소개하며 향후 상업화를 위한 효과적인 적용 방향에 대해서 고찰하고자 한다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.190-193
• /
• 2002

The processing technology of organic thin-film transistors (Ons) performances have improved fur the last decade. Gate insulator layer has generally used inorganic layer, such as silicon oxide which has properties of a low electrical conductivity and a high breakdown field. However, inorganic insulating layers, which are formed at high temperature, may affect other layers termed on a substrate through preceding processes. On the other hand, organic insulating layers, which are formed at low temperature, dose not affect pre-process. Known wet-processing methods for fabricating organic insulating layers include a spin coating, dipping and Langmuir-Blodgett film processes. In this paper, we propose the new dry-processing method of organic gate dielectric film in field-effect transistors. Vapor deposition polymerization (VDP) that is mainly used to the conducting polymers is introduced to form the gate dielectric. This method is appropriate to mass production in various end-user applications, for example, flat panel displays, because it has the advantages of shadow mask patterning and in-situ dry process with flexible low-cost large area displays. Also we fabricated four by four active pixels with all-organic thin-film transistors and phosphorescent organic light emitting devices.

• 한국입자에어로졸학회지
• /
• 제5권4호
• /
• pp.189-197
• /
• 2009

Wet-type particulate removal system is employed in most of ironmaking processes. These de-dusting systems require additional downstream aggregates for treatment of water and for drying of the collected slurry. Thus dried slurry can be pressed in shape of briquettes and recycled in the steelmaking process. Different from the wet-type, the dry-type particulate removal systems generate no slurry. A high-temperature, high-pressure de-dusting system with inertial inlet was developed. The target application of this system was to remove particulate matter generated from the novel ironmaking process and other steelmaking processes. In this study we conducted tests with this newly developed system to evaluate the performance of the silica-carbide (SiC) ceramic filters. In addition, for purpose of comparison, we also conducted tests with a unit which has conventional direct inlet. Fe-Particles collected from the novel ironmaking process were used in our tests as test dusts. The temperature and the pressure were kept constant at their respective values $800^{\circ}C$ and $3kg_f/cm^2$.