• Journal of Korean Society on Water Environment
• /
• v.27 no.3
• /
• pp.342-348
• /
• 2011

A hydrodynamic separator using natural free energy provided by bridge was operated for the treatment of stormwater runoff. The separator was automatically controlled by using electronic valve which is connected with pressure meter. Normally the separator was opened during dry days, but it was closed after the capture of first flush. The results indicated that the average pressure and the flow rate were directly affected by the rainfall intensity. The pressure was more than 3 meters as the rainfall intensity was above 5 mm/hr. The percent volume of underflow decreased as the pressure and flow rate increased, but the percent volume of overflow showed an opposite behavior. The concentration of total suspended solids (TSS) in underflow increased as a function of increasing pressure while it decreased in overflow. The TSS separation efficiency was evaluated based on mass balance. It ranged from 30% to 90% with the pressure ranging from 2 to 10 meters, and it was proportional to pressure and flow rate. The analysis of water balance indicated that around 13% of total runoff was captured by the separator as a first flush, and this runoff was separated as underflow and overflow with the respective percent volume of 29% and 71%. The pollutants budget was also examined based on mass balance. The results showed that the percent of TSS, $COD_{cr}$, TN and TP in underflow were 73%, 59%, 7.6% and 49%, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.341-344
• /
• 2008

Lightweight concrete is known for its advantage of reducing the self-weight of the structures, reducing the areas of sectional members as well as making the construction convenient. Thus the construction cost can be saved when applied to structures such as long-span bridge and high rise building. However, the lightweight concrete requires specific mix design method that is quite different from the typical concrete, since using the typical mix method would give rise the material segregation as well as lower the strength by the reduced weight of the aggregate. In order to avoid such problems, it is recommended to apply the mix design method of self-consolidating concrete for the lightweight concrete. Therefore experimental tests were performed as such mechanical properties(compressive strength, dry density and structural efficiency) of concrete and dry shrinkage according to ACI committee 209.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.89-96
• /
• 2004

Many researches have been devoted to developing a model fur bridge scour analysis which can consider both of the erosive potential of flowing water and the relative ability of the soil to resist erosion. The scour rate apparatus that can quantify the erosion rate of the soil has been developed by virtue of the extensive efforts. The scour rate tests were performed on 3 types of the remolding clay samples using the scour rate apparatus. The erosion characteristics of the fine-grained soil samples according to the variation of the remolding loads are examined and the correlation between the soil properties and erosion rates is also analyzed. The results of the tests and analyses show that the soil properties, especially the dry unit weight and the shear strength of the soil have great influence on the erosion characteristics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.1
• /
• pp.121-133
• /
• 2020

Underwater cutting has a different mechanism than dry cutting, and there are more restrictions than benefits. Due to these constraints, research and development of underwater cutting has been very limited. At present, reactor dismantling is emerging as an important task worldwide, and reactor pressure containers, a key part of the reactor, are decommissioned based on underwater cutting. Reactor pressure containers are high-level radioactive waste, which is one of the main goals of today, such as to bridge the gap between environmental, safety, and cutting performance; hence, a process suitable for cutting should be applied. Therefore, many studies are being conducted on underwater cutting in connection with the dismantling of nuclear reactors in various areas in order to find appropriate processes. This paper first introduces the core technology of underwater cutting processes and discusses various processes. The emphasis is then placed on the adequacy of the reactor dismantling application. More specifically, we examine the suitability for the mechanical and thermal cutting processes, respectively, to find a solution suitable for dismantling a reactor. We discuss how each solution can sufficiently perform the specified functions at each stage of reactor dismantling and suggest that these processes can perform all of the work of underwater cutting.

• Journal of Korean Society on Water Environment
• /
• v.22 no.2
• /
• pp.349-357
• /
• 2006

Nowadays, the discharges of urban streams during dry season are depleted because the hydrologic cycle in the watershed has been destroyed due to the expansion of the impermeable area, the excessive groundwater pumping, climate change, and so forth. The streamflow depletion may bring out severe water quality problems. This research are to investigate the hydrologic characteristics and to develop a technology to restore sound hydrologic cycle of Anyangcheon watershed. For the hydrological cycle analysis of the Anyangcheon watershed, continuous simulations of urban runoff were performed for the upstream basin of Gocheok bridge whose basin area covered 4/5 of the whole catchment area. The increase of impervious area by urbanization was analysed and its effect on urban runoff was evaluated. The SWMM 5 (Storm Water Management Model 5) was used for the continuous simulation of urban runoff. The analysis results of urbanization effect on runoff are as follows: the surface runoff in 2000 increases to 65% of the whole precipitation whereas the surface runoff in 1975 amounts to 50% of the precipitation; the groundwater runoff in 2000 amounts to 7% and shows 6% decrease during the period from 1975 to 2000.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.269-272
• /
• 2004

After concrete casts, temperature decent and shrinkage bring volume changes of concrete pavement. Microcracking and cracking in concrete pavement are caused by these volume changes. As a result, durability of concrete pavement is deteriorated. Recently, Very-Early Strength Latex Modified concrete(below:VESLMC) from the beginning of High-Way is used as urgent repair material for bridge deck. The advantage of VESLMC is that compressive and flexural strength at 3 hours age are 4.5MPa and 21MPa respectively. It allows the traffic to open in 3 hours. But, this material has the problem which is early-age shrinkage cracking caused by water self-dissipation with rapid hydration reaction and water evaporation with body dry. Unfortunately, until now, the research about early-age shrinkage of VESLMC leaves something to be desired. Therefore, the purpose of this study is to present the early-age shrinkage of VESLMC respect to latex contents and shrinkage ratio to maximum length change that can help field engineers' skill. Latex contents of 0, 5, 10, 15, $20\%$ in standard of same workability in VESLMC are selected by experimental variables. After initial set, shrinkage value was measured with 10mm LVDT for 3 days. The results of maximum shrinkage ratio were 0.019, 0.017, 0.023, $0.027\%$ respectively.

• Journal of Navigation and Port Research
• /
• v.30 no.6 s.112
• /
• pp.447-455
• /
• 2006

Together with the trend of enhancement in domestic industrial development and economic progress due to import and export, the demand for construction of the roads, bridges, especially port facilities, and several coastal protection and ocean structures is increasing rapidly. MOMAF of Korean Government is driving construction cf 9 new ports and renovation cf the existing fishery ports. Among these structures most of bridge base, wharves, dolphins, quays, and jetties are being newly built cf steel or concrete pile. As the base, supporting bulkheads, and piles are underwater after construction, it is difficult to figure out the status of structures and not enough to get maintenance and strengthen the structures. Every year, moreover, these works suck the government budget due to higher incomplete maintenance expense for protection from corrosions cf structures and increased underwater construction period. For the purpose cf cutting down the expense cf government budget, it is necessary to extend the life cycle of the existing structures. Therefore, we developed a new method for maintenance of submerged structures near the waterline by allowing dry work environment with the floating caisson. The method shows easy to move around the working area and handle. It also showed not only a significant reduction of maintenance expenses and time for anti-corrosion work but also better protection This will be a milestone to reduce the maintenance and construction expenses for the shore and water structures.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.06b
• /
• pp.163-170
• /
• 2006

Together with the trend of enhancement in domestic industrial development and economic progress due to import and export, the demand for construction of the roads, bridges, especially port facilities, and several coastal protection and ocean structures is increasing rapidly. MOMAF of Korean Government is driving construction of 9 new ports and renovation of the existing fishery ports. Among these structures most of bridge base, wharves, dolphins, quays, and jetties are being newly built of steel or concrete pile. As the base, supporting bulkheads, and piles are underwater after construction, it is difficult to figure out the status of structures and not enough to get maintenance and strengthen the structures. Every year, moreover, these works suck the government budget due to higher incomplete maintenance expense for protection from corrosions of structures and increased underwater construction period. For the purpose of cutting down the expense of government budget, it is necessary to extend the life cycle of the existing structures. Therefore, we developed a new method for maintenance of submerged structures near the waterline by allowing dry work environment with the floating caisson. The method shows easy to move around the working area and handle. It also showed not only a significant reduction maintenance expenses and time for anti-corrosion work but also better protection. This will be a milestone to reduce the maintenance and construction expenses for the shore and water structures.

• Journal of Wetlands Research
• /
• v.23 no.3
• /
• pp.252-259
• /
• 2021

Numerous valley waters originating from Mt. Mudeung and flowing into Gwangju Cheon flowed into the confluence-type sewage conduit, the Gwangju Cheon became dry and water quality deteriorated. In this study, a method to create a stream was studied by using the valley water of Mt. Mudeung in the Gwangju cheon that flows into the sewage treatment plant as a water source. Flow and water quality surveys were investigated at four points with meaningful flow quantity. As a result, it showed a flow quantity was 105~2,721 m³/day at each point. And the average water quality was BOD₅ 0.3~1.6 mg/L. If a stream with a flow quantity of 1,500 m³/day is created during the dry season and then flows into the Namgwang bridge of Gwangju cheon, it is predicted that there will be improvements in BOD 7.3%, COD 6.5%, T-P 5.8%, and T-N 5.2%. In addition, it was determined that the load on the flow quantity of the sewage treatment plant due to the inflow of valley water would be reduced, the cost of sewage treatment would be reduced, and it would be the basis for BGN construction by creating waterside amenity in the city.

• Journal of the Society of Disaster Information
• /
• v.20 no.2
• /
• pp.329-338
• /
• 2024

Purpose: This study verified the safety of the improved box-type girder behavior by comparing and evaluating the bending behavior results of a full-scale specimen based on the analytical behavior of the splice element PSC U-shaped girder with integrated tensioning systems. Method: Based on the results of the service and strength limit state design using the bridge design standard(limit state design method), the applied load of a 40m full-scale specimen was calculated and a static loading experiment using the four-point loading method was performed. Result: When the design load, crack load, and ultimate load were applied, the specimen deflection occurred at 97.1%, 98.5%, and 79.0% of the analytical deflection value. When the design load, crack load, and ultimate load were applied, the crack gauge was measured at 0.009~0.035mm, 0.014~0.050mm, and 6.383~5.522mm at each connection. Conclusion: The specimen behaved linear-elastically until the crack load was applied, and after cracks occurred, it showed strainhardening up to the ultimate load, and it was confirmed that the resistance of bending behavior was clearly displayed against the applied load. The cracks in the dry joints were less than 25% of grade B based on the evaluation of facility condition standard. The final residual deformation after removing the ultimate load was 0.114mm, confirming the stable behavior of the segment connection.