• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.996-1001
• /
• 2010

Recently, the demand of ceramic metal halide lamp has been expanded. Therefore, the lamp with high efficiency and long lifetime are increasing and the evaluation of reliability is needed. In this paper, the degradation phenomena of ceramic metal halide lamp was studied. The lamp was tested for 3000 on/off cycles with each cycle having a duration of 20 minutes on and 20 minutes off based on the accelerated aging experiment based on "Reliability Standards RS C 0085". As result, the corrosion of arc tube and leak was appeared from reaction between inner wall of PCA and chemical elements, and distortion of electrode was resulted from difference of thermal expansion between arc tube of PCA and electrode. Also, the efficiency of lamp was decreased by the change of inner pressure, operation temperature, and driving voltage from wall blackening.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.4
• /
• pp.231-235
• /
• 2015

Bimodal Tram developed by KRRI is driven by a series Hybrid propulsion system which has both the CNG engine, generator and LPB(Lithium Polymer Battery) pack. It has three driving modes; Hybrid mode, Engine mode and Battery mode. Even in case of Battery mode, LPB pack to get enough power to drive the vehicle only by itself onsists of 168 LPB cells(80Ah per lcell), 650V. It is important thing to manage LPB pack in a right way, which will extend the lifetime of LPB cells and operate in the hybrid mode effectively. This paper has shown the development of battery management system(12 BMS, 1 BMS per 14cells) to manage LPB pack which is connected with CAN(Controller Area Network) each other and measure the voltage, current, temperature and also control the cooling fan inside of LPB pack. Using the measured data, BMS can show the SOC(State of Charge), SOH(State of Health) and other status of LPB pack including of the cell balancing.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.365-370
• /
• 2004

The integration of intelligent devices, devices-level networks, and software into motor control systems can deliver improved diagnostics, fast warnings for increased system reliability, design flexibility, and simplified wiring. Remote access to motor-control information also affords an opportunity for reduced exposure to hazardous voltage and improved personnel safety during startup and trouble-shooting. This paper presents LonWorks fieldbus networked intelligent induction control system architecture. Experimental bed system with two inverter motor driving system for controlling 1.5kW induction motor is configured for LonWorks networked intelligent motor control. In recent years, MCCs have evolved to include component technologies, such as variable-speed drives, solid-state starters, and electronic overload relays. Integration was accomplished through hardwiring to a programmable logic controller (PLC) or distributed control system (DCS). Devicelevel communication networks brought new possibilities for advanced monitoring, control and diagnostics. This LonWorks network offered the opportunity for greatly simplified wiring, eliminating the bundles of control interwiring and corresponding complex interwiring diagrams. An intelligent MCC connected in device level control network proves users with significant new information for preventing or minimizing downtime. This information includes warnings of abnormal operation, identification of trip causes, automated logging of events, and electronic documentation. In order to show the application of the multi-motors control system, the prototype control system is implemented. This paper is the first step to drive multi-motors with serial communication which can satisfy the real time operation using LonWorks network.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.153-157
• /
• 2009

A Highly efficient Mercury-free Flat Fluorescent Lamp (MFFL) with dielectric barrier Xe gas discharge was developed for an alternative of conventional line-type Cold Cathode Fluorescent Lamps (CCFLs) which shows a wide voltage margin and a stable discharge operation for diffuse glow discharge with an application of a auxiliary electrode. Electro-optic characteristics of the MFFL were examined through the changes in ambient temperature, total pressure and Xe partial pressure. the single cell is expanded into a multi-structured configuration to realize a large sized lamp by a simple repetition of the single cells, and a new driving scheme is proposed for an adaptive brightness control using dual auxiliary electrodes and bi-polar drive scheme. In addition, interesting application of this ultra high luminance flat lamp by the optimization of the gas condition and the pattern of the rear phosphor layer is suggested as a good alternative of daylight lamp source

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.3
• /
• pp.223-230
• /
• 2001

This power proposes a new sensorless drive system for the trapezoidal brushless DC motor generally requiring mechanical position or speed sensor. For this an indirect rotor position sensing method from the back emf waveform of non-conducting phase is explained. Back emf waveform of non-conducting is obtained from analysing terminal voltage created by making Y-connection. And an experiment is implemented with a driving system which use 87c196mc microcontroller having a peripheral associated with 3-phase signals and inverter composed of Power MOSFET. The experimental results show the validity and practicality of the proposed sensorless drive.

• Journal of Information Display
• /
• v.12 no.3
• /
• pp.115-119
• /
• 2011

Optically isotropic liquid crystal (LC) mixture such as blue-phase LC and nanostructured LC composites exhibit the advantages of fast response time, high contrast ratio and wide-viewing angle due to the induced birefringence along the horizontal electric field. Utilizing this mixture, a novel single cell gap in-plane switching-type polymer-stabilized blue-phase transflective liquid crystal display by embedding the nanowire grid polarizer as a polarization-dependent reflective polarizer in the R region is proposed. This device can be used as a normal black mode without any quarter-wave plate or patterned in-cell phase retarder. Moreover, the transmittance is identical to the reflectance so that it will be suitable for single gamma driving. Detailed electro-optic performances, such as voltage-dependent light efficiency and viewing angle of the proposed device configuration, are investigated.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.506-513
• /
• 2001

The torque of an SRM depends on the phase current and derivative of inductance. But an SRM is difficult to control the desired torques because of saturation in magnetic circuit An SRM is controlled by parameters of input voltage, and switch on , off angle The switch on off angles of an SRM regulate the magnitude and shape of current waveform and decide the magnitude and shape of torque This paper proposes an the optimization control scheme by adjusting both the switch on an switch off angle . The switch off angles are decided by reference of efficiency using simulation and experiments. The switch on angles are decided by load torque , And the dwell angles are controlled for torque control and speed control using GA-neural network which is used to simulated the reasonable switching angle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.562-568
• /
• 2008

In this paper, the hole injection layer(HIL) materials have been synthesized and analyzed. Their HOMO levels are $4.93{\sim}5.22\;eV$, and their energy band gaps are $2.74{\sim}3.19\;eV$. Their glass transition temperatures($T_g$) are all above $114^{\circ}C$, which implies that they are highly thermal-stable. The green OLED devices with a structure of ITO(150 nm)/NEW_HIL(50 nm)/NPB(30 nm)/$Alq_3$(50 nm)/Al:Li(100 nm) were fabricated and tested, incorporating these newly synthesized HIL materials. According to the test results of OLED devices, the I-V-L performances of these devices increase in the following sequence: ELM307 > ELM200 > ELM321 > ELM327 > ELM325. In addition, the OLED device with ELM307 as a HIL has the highest brightness and efficiency at the same driving voltage. These experimental results have shown that ELM307 can be used as one of the most promising candidates for HIL materials.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.5
• /
• pp.381-386
• /
• 2012

To study encapsulation method for large-area organic light emitting diodes (OLEDs), red emitting OLEDs were fabricated, on which $Alq_3$ as organic buffer layer and LiF and Al as inorganic protective layers were deposited to protect the damage of OLED by epoxy. And then the OLEDs were attached to flat glass by printing method using epoxy. The basic structure of OLED doped with rubrene of 1 vol.% as emitting layer is ITO(150 nm) / 2-TNATA(50 nm) / ${\alpha}$-NPD(30 nm) / $Alq_3$:Rubrene(30 nm) / $Alq_3$(30 nm) / LiF(0.7 nm) / Al(100 nm). In case of depositing $Alq_3$, LiF and Al and then attaching of flat glass onto OLED, current density, luminance, efficiency and driving voltage were not changed and lifetime was increased according to thickness of Al as inorganic protective layers. The lifetime of OLED/$Alq_3$/LiF/Al_4/glass structure was 139 hours increased by 15.8 times more than bare OLED of 8.8 hours and 1.6 times more than edge sealed OLED of 54.5 hours.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1451_1452
• /
• 2009

Owing to the increasing number of intelligent homes(or called Smart home), the corresponding cost is much higher. Low voltage circuit breakers are widely used in the intelligent homes to interrupt fault current rapidly and to assure the reliability of the power supply. The distribution of magnetic field induced by arc current in the contact system of molded case circuit breaker depends on the shape, arrangement, and kinds of material of grids. This paper is focused on understanding the interrupting capability, more specifically of the grid and the arc runner, based on the shape of the contact system in the current MCCB. The magnetic driving force was calculated by using the flux densities induced by the arc current, which are obtained by three-dimensional finite element method. There is a need to assure that the optimum design required to analyze the electromagnetic forces of the contact system generated by current and the flux density be present. This is paper present our computational analysis on contact system in MCCB.