• International Journal of Fluid Machinery and Systems
• /
• v.9 no.1
• /
• pp.39-46
• /
• 2016

A high frequency hydraulic rock drill drifter with sleeve valve is developed to use on arm of excavator. In order to ensure optimal working parameters of impact system for the new hydraulic rock drill drifter controlled by sleeve valve, the performance test system is built using the arm and the hydraulic source of excavator. The evaluation indexes are gained through measurement of working pressure, supply oil flow and stress wave. The relations of working parameters to impact system performance are analyzed. The result demonstrates that the maximum impact energy of the drill drifter is 98.34J with impact frequency of 71HZ. Optimal pressure of YZ45 rock drill is 12.8 MPa-13.6MPa, in which the energy efficiency reaches above 58.6%, and feature moment of energy distribution is more than 0.650.

• Geomechanics and Engineering
• /
• v.28 no.1
• /
• pp.25-33
• /
• 2022

The energy transferred on drill rods by dynamic impact mainly determines the penetration depth for in-situ tests. In this study, the dynamic response and transferred energy of drill rods are determined from the frequency of the stress waves. AW-type drill rods of lengths 1 to 3 m are prepared, and strain gauges and an accelerometer are installed at the head and tip of the connected rods. The drill rods are hung on strings, allowing free vibration, and then impacted by a pendulum hammer with fixed potential energy. Increasing the rod length L increases the wave roundtrip time (2L/c, where c is the wave velocity), and hence the transferred energy at the rod head. At the rod tip, the first velocity peak is higher than the first force peak because a large and tensile stress wave is reflected, and the transferred energy converges to zero. The resonant frequency increases with rod length in the waveforms measured by the strain gauges, and fluctuates in the waveforms measured by the accelerometer. In addition, the dynamic response and transferred energy are perturbed when the cutoff frequency is lower than 2 kHz. This study implies that the resonant frequency should be considered for the interpretation of transferred energy on drill rods.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.1
• /
• pp.94-98
• /
• 2023

In the case of high-speed data transmission on high multilayer boards, signal coherence is a problem, especially due to the via hole, and a solution to improve return loss or insertion loss by applying a back drill to the via hole is being proposed. In this paper, Near-Field Electromagnetic measurements were made on a high multilayer board to determine how the presence or absence of back drill affects signal consistency. For this purpose, we used a signal generator, spectrum analyzer, and EMC scanner on a test board to determine if it is possible to distinguish between areas with and without back drill in the via holes of the stubs on the board. Also, we analyzed the measured value of S11, S21 and EMC etc. for how much it improves the signal attenuation of the stub with back drill. Through this, we knew that less electromagnetic waves are generated the stub via with back drill. At future research, we will analyze how much it improves the signal loss and electromagnetic waves due to the depth of back drill.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.4
• /
• pp.360-365
• /
• 1991

This experiment was conducted to determine mechanized seeding ability of barley drill seeder on the seeding time, growth and yield of sorghum-sudangrass hybrid. The time required for machine drill seeding was 42 minutes per l0a which was one-thirteenth of the time required by the manual drill seeding, and percentage of seedling establishment by machine drill seeding was better than that of manual drill seeding. Leaf area index in seeding rate with 30 x 5cm and 40 x 5cm of machine drill seeding was higher than those of manual drill seeding, the leaf distribution was better and the total nonstructural carbohydrate content of stubble after cutting was short increased than that of manual drill seeding, Content of feed composition was not significantly different between manual and machine drill seeding. At seeding rate of 40 x 5cm of machine seeding. dry matter and TDN yield were increased to 29% and 30% respectiyely, than those of manual drill seeding.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2022.10a
• /
• pp.102-102
• /
• 2022

More than 74% of forage crops in Korea are cultivated in winter rice fields. Italian ryegrass (IRG) can be said to be a representative forage crop, but over 70% of its seeds are dependent on imports. In addition, there are concerns that the stable supply of research fees may be disrupted due to the effects of climate change, war, and other factors. Therefore, it is necessary to secure a large production area for stable supply. Korea's reclaimed land area is 135,000 ha and its agricultural area is 112,000 ha. Therefore, this study attempted to apply IRG to the domestic IRG seed industry through stable cultivation techniques on reclaimed land. In this study, IRG 'Kowiearly' varsity was cultivated in late October 2020 and early October 2021 in the Saemangeum reclaimed land. The seeding methods were conventional drill sowing seeding, new technology spot seedling (30 × 18 cm) and new technology drill sowing seeding. The amount of sowing was conventional drill sowing seeding 2.0(kg/10a), new technology spot seedling 1.5(kg/10a), and new technology drill sowing seeding 1.5(kg/10a). Fertilizer application amount is conventional drill sowing seeding(N-P₂O₅-K₂O) 9.0-12-12(kg/10a), and new technology spot seedling and drill sowing seeding were(N-P₂O₅-K₂O) 4.5-12-12(kg/10a) respectively. Fertilizer was applied accordingly. After that, in February, the conventional drill sowing seeding, new technology drill sowing seeding and spot seedling applied 4.0 and 2.2(kg/10a) of nitrogen supplement fertilizer, respectively. Before wintering, plant length was higher in 2022 than in 2021, but leaf number was higher in 2021. Heading time was April 30, 2021 and April 25, 2022. In heading time, plant length was 74 cm in 2021 and 67 cm in 2022, lower than in 2021. On the other hand, There was no difference in the number of panicle and the number of seeds in the 2021 harvester in all treatment plots, and, thus seed yield was no differ. However, the drill sowing seeding and spot seedling of the new technology were somewhat higher than the conventional drill sowing seeding. On the other hand, seed yield was decreased in all treatment plots compared to 2022 because of raifall deficiency in 2021.

• The Journal of Korean Academic Society of Nursing Education
• /
• v.18 no.3
• /
• pp.424-435
• /
• 2012

Purpose: The purpose of this study was to investigate the disaster experience (accidents, education etc) and the concern for disaster preparedness of college students. Methods: This research design was a descriptive study. Data were collected from November 1, 2011 to December 30, 2011 and analyzed by the SPSS PASW statistics 18.0 program. Results: There were statistical significances in major (p<.050), grade(p<.001), and a completed disaster class(p<.001) between general characteristics and concern for disaster preparedness. The major disaster events that occurred from 2003 to 2010 in Korea were the 2007 Taean oil spill (85.4%), the 2003 Daegu subway fire (82.7%), and the 2008 Sungnyemun fire (62.9%). The possible disaster events in Korea were hurricanes, floods, fires (including wildfire), and the shutdown of communication lines. Subjects learned about cardiopulmonary resuscitation (18.2%), first aid for bleeding and fractures (17.8%), a fire drill (14.3%), and an escape drill for an earthquake (14.0%). They wanted to learn the fire drill (11.33%), the escape drill for an earthquake (9.7%), a war drill (9.0%), a disaster confrontation drill on the subway (8.6%), and a fire and explosion evacuation drill (8.4%). Half of subjects were not prepared with emergency supplies for disasters because they thought that a disaster would not occur. Conclusion: It is necessary to develop the disaster educational programs according to subject's demands in Korea.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.41 no.1
• /
• pp.28-33
• /
• 1996

This experiment was carried out at National Crop Experiment Station in 1994 to obtain basic information of growth characters and yield of rice under various seeding methods in direct seeding on dry paddy. Hwaseongbyeo sown on April 27 by flat drill seeding, high ridged drill seeding and hill seeding under different seed conditions, soil convering after seeding and irrigation methods. Nitrogen applied 150kg /ha by 3 times split application at rate of 40:30:30％ (basal: 5th leaf stage:panicle initiation stage). Seedling stands were higher in flushed irrigation water after seeding than in irrigation at 3rd leaf stage, and it also was higher in high ridged drill seedings than in flat drill seedings. Days for seedling stand, heading date were shorten 6~10 days, 2~3 days by flushed irrigation water after seeding, respectively. Number of tiller was more in high ridged drill seedings than conventional seedling method(Flat drill seeding ＋ intact seed ＋ soil covering after seeding ＋ irrigation at 3rd leaf stage after seedling stand) at early growth stage, but the most tiller number was highest in developed seeding method(Flat drill seeding ＋ soaked seed ＋ non soil covering after seeding ＋ fulshed irrigation water after seeding) at heading stage among used seeding methods. Lodging index was slightly high in high ridged drill seeding and conventional seeding. Field lodging was degree 1 in high ridged drill seedings and developed seeding, Milled rice yield in developed seeding was increased 7％ compaired with conventional seeding(5.35t /ha).

• Journal of the Institute of Convergence Signal Processing
• /
• v.16 no.3
• /
• pp.90-95
• /
• 2015

This study presents a method to test quite small-sized and light-weighted micro-drill bits which are used to make holes in printed circuit boards(PCB). After getting images of micro-drill bits through the high resolution microscope, we developed image processing algorithms to detect fiducial points, and then measured diverse factors of the drill-bit based on these points. We also developed the window-based inspection system to automatically discriminate normal and abnormal status. For the relative comparison of its performance, the system was compared with an existing inspection system using test images. Experimental results showed that the proposed system slightly improved performance, and also classified correctly some misjudged errors which were occurred in the existing system.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.3
• /
• pp.161-166
• /
• 2017

Inconel 718, a typical ultraheat-resistant alloy, is recognized as a useful component in aircraft parts owing to its high-temperature strength and good chemical stability. Although many studies have been conducted to determine the proper drill shape to overcome the poor machinability when drilling into Inconel 718, most have involved a cutting process program known as AdvantEdge, as an experimental approach requires much time and money. In this study, our purpose is to optimize the drill shape for efficient drilling by conducting a trust force and temperature analysis using AdvantEdge. In order to achieve this purpose, the reliability of the results of the analysis was verified and by applying design of experiment an analysis of the geometric parameters of the drill shape considering the thrust force and temperature was conducted.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.888-891
• /
• 2000

Drilling is one of the most important operations in machining industry and usually the most efficient and economical method of cutting a hole in metal. From automobile parts to aircraft components, almost every manufactured product requires that holes are to be drilled for the purpose of assembly, creation of fluid passages, and so on. It is therefore desirable to monitor drill wear and hole quality changes during the hole drilling process. One important aspect in controlling the drilling process is drill wear status monitoring. With the monitoring, we may decide on optimal timing for tool change. The necessity of the detection of tool wear, fracture and the abnormal tool state has been emphasized in the machining process. Accordingly, this paper deals with the cutting characteristics of the hot-rolled high strength steels using common HSS drill. The performance variables include drill wear data obtained from drilling experiments conducted on the workpiece. The results are obtained from monitoring of the cutting force and Acoustic Emission (AE) signals, and from the detection of the abnormal tool state with the computer vision system.