• The Journal of the Korean dental association
• /
• v.53 no.2
• /
• pp.132-142
• /
• 2015

Purpose : The objective of this research was to investigate an optimization of drill design factors for implant stability and efficacy through comparative evaluation by the cutting time, heat generation and initial stability. Materials and Methods : Three design factors were considered for the purpose of drill design optimization; the number of flute(2 flute, 3 flute), helix angle($15^{\circ}$, $25^{\circ}$) and drill tip shape(straight, 2-phase). Design factors were selected through comparative evaluation by temperature change, cutting time and ISQ value. Results : Heat generation and cutting time are influenced by all design factors(p<0.05). Drill tip shape was the only factors which influenced to the largest initial stability(p<0.05). Conclusion : Drills with 2 flutes, 2-phase formed drill tip, and 25 degrees of helix angle exhibit a better performance than other design.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.3 s.168
• /
• pp.15-20
• /
• 2005

This paper describes the PCB drilling using an ultra high-speed air bearing spindle system and micro drill. For this research, we have developed the ultra high-speed air bearing spindle of 125,000 rpm and made an experiment for the application possibility in the PCB drilling. In order to estimate the drilling performance, we have investigated the size and damage of drilled hole, and the wear of drill at 90,000rpm. Results are as follows; we have confirmed the possibility in the PCB drilling of air bearing spindle. In case of micro-drilling PCB at $0.1mm\sim0.3mm$, the increase in the number of drilling has resulted in a bigger size of holes and also a bigger size of damage. It has been found that the wear of micro drill tends to concentrate in the main cutting edge.

• Tunnel and Underground Space
• /
• v.13 no.4
• /
• pp.316-320
• /
• 2003

This study is to evaluate an irregular drill-hole depth having an effect on the blast vibration. The relationship between a peak particle velocity and a cube root scaled distance with respect to three drill-hole depths with 2.1m, 2.3m and 2.4m are compared and analyzed using a numerical regression analysis. According to the results, the deeper a drill-hole depth is the larger a peak particle velocity is. It is suggested that a drill-hole depth is proportional to a peak particle velocity at the same scaled distance. Therefore, a regular drill-hole should be carried out in order that the blast vibration velocity of a fixed range under a allowable vibration velocity is maintained.

• Explosives and Blasting
• /
• v.25 no.1
• /
• pp.67-77
• /
• 2007

The drill monitoring data are useful for the detection of abrupt and unexpected changes in ground renditions. This paper introduces a new approach to how drill performance parameters can be used for the prediction of quantitative rock mass properties ahead of tunnel face and the blasting design. The drill monitoring parameters available for the predictions include the instantaneous advance speed, thrust force, torque, tool pressure and penetration rate. The assessment of the drill monitoring parameters will be able to build a database provided that in-situ drill monitoring informations are accumulated and enable us to make a reasonable blast design based on quantitative assessment of rock mass.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1021-1024
• /
• 2001

Out of all metal-cutting processes, the hole-making process is the most widely used. It is estimated to be more than 30% of the total metal-cutting process. It is therefore desirable to monitor and detect drill wear during the hole-drilling process. In this paper, the vision system of the sensing methods of drill flank wear on the basis of image processing is used to detect the wear pattern by non-contact and direct method and get the reliable wear information about drill. In image processing of acquired image, median filter is applied for noise removal. The vision flank wear area of the drill was measured. Backpropagation neural networks (BPns) were used for no-line detection of drill wear. The neural network consisted of three layers: input, hidden and output. The input vectors comprised of spindle rotational speed, feed rates, vision flank wear, thrust and torque signals. The output was the drill wear state which was either usable or failure. Drilling experiments with various spindle rotational speed and feed rates were carried out. The learning process was peformed effectively by utilizing backpropagation. The detection of the abnormal states using BPNs achieved 96.4% reliability even when the spindle rotational speed and feedrate were changed.

• Journal of the Korean Society for Precision Engineering
• /
• v.2 no.3
• /
• pp.28-40
• /
• 1985

In this study, to check up on the effect of the components of cutting resistance upon friction between drill and inside wall of hole in drilling, the experiment was performed with individual specimen of carbon steel, cast iron, aluminium alloy under various cutting conditions: depth of hole, cutting speed, feed rate, shape and material of specimen. On the basis of the experimental results, the following conclusions are drawn; 1. The components of cutting resis- tance were increased in proportion to the increase of depth of hole owing to frictional resistance of drill margin and chip-jamming. 2. As feed rates increase, torque and thrust were increased. When comparing to the increasing rate for these components respecitively, thrust is higher tendency than torque. 3. As drill diameter increase, torque and thrust were increased. When comparing to the increasing rate for these components respectively, torque is higher tendency than thrust. 4. In the case of torque, the frictional resistance between drill margin and inside wall of drilled hole accounts for about 20 percent of carbon steel, 14 of cast iron, 10 aluminium alloy in drilling. But the effect of thrust force could be negligible. 5. Comparison between the theoretical and experimental results showed a close agreement so far as depth of hole is about three times of drill diameter. But there was a wide difference between them beyond the rane of three times, because of characteristics of the drilling process.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2340-2348
• /
• 1992

Recently, various film coated insert tools have been used in order to improve tool life by several different vapor deposition or chemical vapor deposition. Especially, TiN coated drills have been broadly studied because of improving drill performance in terms of drill life, work quality and its brilliant color. Nevertheless, because of the poor adhesion between TiN film and drill, it was difficult to attain the better drill performance. Therefore, to improve adhesion of TiN films, we sputtered titanium as interlayer prior to TiN deposition on drill by PECVD(Plasma Enhanced Chemical Vapor Deposition). The results indicate that Ti/TiN coated drills achieve about 2.6 times life improvement, while TiN coated drills only 2 times. Wear characteristics of tested drills were examined using SEM, and the results were correlated with drill life and roughness of drilled holes.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2001.12a
• /
• pp.74-77
• /
• 2001

One of the most important technology in PA(Factory Automation) is to construct the diagnostic system for manufacturing process. To improve the productibility in the factory, the state of tools such as bite, drill, endmill should be monitored continuously. In this study, fuzzy logic was used to check the wear of drill in drilling process. The input variables to construct the fuzzy rules are cutting force and the rate of cutting force's change. The experiment was done with the fixed spindle speed and feed rate in cutting condition.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.80-84
• /
• 1996

The effects of guide pads on burnishing action and accuracy of machined hole are investigated in drilling with burnishing drill using a speciaaly designed tool experimentally. The cutting forces are balanced at the small forward regions of guide pads. The burnishing action takes place under a high contact pressure between the bore wall and those regions. The over size mechanism of machined hole by the guide pads is discussed.

• Journal of the Society of Disaster Information
• /
• v.6 no.2
• /
• pp.107-117
• /
• 2010

The disaster preparedness system in Korea has been developed in spite of many obstacles, but there are still many problems especially on actual preparedness including disaster drill and disaster medical system. Disaster drills performed by wide regional emergency medical centers for one years were analyzed based on the disaster drill report and additional compensation of incomplete data by direct contact with the participating institutions. On the disaster medical drills in Korea, it is necessary to emphasize drills on various types of disaster, active participation of medical personnels, drills combined with various types of related institutions, process of disaster medical aspect.