• 전기학회논문지
• /
• 제59권5호
• /
• pp.854-859
• /
• 2010

Distribution Automation System(DAS) is designed to improve operational efficiency by acquisition and control of remote data using its components such as central computation units, communication network and feeder remote terminal units. A conventional human machine interface of the DAS adopts a schematic diagram which is made by drawing power equipments on the geographic information system map. The single line diagram is more useful than the schematic diagram for the main tasks of distribution system operation such as protective relay coordination, service restoration and loss minimization. Since the configuration of the distribution line is changed according to the relocation of the open tie switches, the auto-drawing algorithm based on the connection between the sections and the switches is an essential technique. This paper proposes a new auto-drawing algorithm for a single line diagram of distribution systems based on tertiary tree and collision avoidance method. The feasibility of the proposed algorithm has been testified for various cases using practical distribution system with 12 feeders.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.149-154
• /
• 2001

This paper presents the experimental study of the static stiffness for the BT Shank(7/24 Long Taper) and the HSK Tool Shank(1/10 Short taper). The static stiffness test was performed under different experimental conditions. The results obtained are as follows ; As known in the analysis results of the Load-Deflection diagram of the 7/24 Test tool shank, it is turned out that the diagram is a linear characteristics without regard to axial drawing force and according as the axial drawing force get to the 6kN, the static stiffness of the shank increase linearly. Thus the effective axial drawing force which maintains the static stiffness of the Main spindle taper of Machine Tool is larger than 6kN. It is found that the Load-Deflection diagram with 6kN of drawing force in the 1/10 Test tool shank is characterized by non-linear. But according as the axial drawing force is increasing by the 8kN, the diagram is characterized by linear. And increasing amount of deflection is about 60%. Therefore commendable axial drawing force is larger than 8kN. As a result, considering that the actual drawing force of the Machining Center is about 1300kgf and axial drawing force 12kN is equivalent amount as a 1220kgf, it is turned out that 1/10 Test tool shank superior to 7/24 Test tool shank in the static stiffness.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제49권5호
• /
• pp.278-286
• /
• 2000

A new large-scale network geometric analysis is introduced. For a large-scale circuit, it must be analyzed with a geometric diagram and figure. So many equations are induced from a geometric loop-node diagram. The results are arranged into a simple matrix, of course. In case of constructing a network diagram, it is not easy to handle voltage and current sources together. Geometric loop analysis is related to voltage sources, and node analysis is to current sources. The reciprocal transfer is possible only to have series or parallel impedance. If not having this impedance, in order to obtain equivalent circuit, many equations must be derived. In this paper a loop-reduction method is proposed. With this method current source branch is included into the other branch, and disappears in circuit diagram. So the number of independent circuit equations are reduced as much as that of current sources. The number is not (b-n+1), but (b-n+1-p). Where p is the number of current sources. The reduction procedure is verified with a geometric principle and circuit theory. A resultant matrix can be constructed directly from this diagram structure, not deriving circuit equations. We will obtain the last results with the help of a computer.

• 조명전기설비학회논문지
• /
• 제26권7호
• /
• pp.23-29
• /
• 2012

A single line diagram is a graphic user interface to represent electrical connectivity between power equipments in distribution automation systems. This paper proposes a new single line auto-drawing technique based on the service oriented architecture. Web service, CIM(Common Information Model) and SVG(Scalable Vector Graphics) are adopted to implement SOA concept. A web service demo system was established which is configured with the service provider, consumer and broker to verify the feasibility of this study.

• 산업기술연구
• /
• 제19권
• /
• pp.67-74
• /
• 1999

The mechanical properties including forming limit and deep-drawability of commercially-used sheet metals were experimentally estimated in this study. Uniaxial tensile test to obtain basic mechanical properties was carried out, followed by limiting dome height (LDH) test and forming limit diagram (FLD) test to quantitatively evaluate the sheet-formability. Deep drawing and reverse drawing tests were also performed to find out the critical values of the blank holding force and the gap between the die and the blank holder which enabled the deep drawing and reverse drawing of a successful cop without any wrinkle or fracture. The thickness of the cup wall along the rolling-, transeverse- and $45^{\circ}$-directions was measured and compared with one another. And the punch force-stroke curve and the critical punch force expected from the theory coincided with the experimental result very well for mild steel while not for aluminium alloy.

• 플랜트 저널
• /
• 제17권3호
• /
• pp.37-41
• /
• 2021

P&ID(Piping and Instrument Diagram)는 플랜트의 장치 및 계장 정보를 집약적으로 담고 있는, 엔지니어링 핵심도면이다. 한 장의 P&ID에는 심볼로 표현된 수백 여개의 정보들이 존재하며, 이에 대한 디지털 전산화 작업이 수작업으로 진행되고 있어 많은 인력과 시간이 소요된다. 기존 연구들은 CNN 모델을 이용하여 도면 객체 검출에 성공하였으나, 도면 한 장당 약 30분, 인식률은 90% 정도로 현장에서 구현하기에는 부족한 성능이다. 따라서 본 연구에서는 영역 검출과 객체 인식을 동시에 처리하는 1-stage 객체 검출 알고리즘을 제안하였다. 이미지 레이블링 오픈소스 툴을 이용하여 학습 데이터를 구축하고 딥러닝 모델 학습을 통해 도면 내 심볼 이미지 인식 방법을 제안한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.556-559
• /
• 2008

In this study, the failure in circular cup deep drawing simulation at warm temperature is predicted using forming limit diagram (FLD). The FLD is used in sheet metal forming analysis to determine the criterion for fracture prediction. The simulation with heat transfer of circular cup deep drawing at warm temperature was conducted. To predict the failure, the simulation with heat transfer used FLD at temperature in the vicinity of maximum thinning. The result of the simulation with heat transfer shows that the drawn depth increases with increasing temperature and is in accord with the experimental results above $150^{\circ}C$. The FLD provides a good guide for the failure prediction of warm forming simulation with heat transfer.

• 한국실내디자인학회논문집
• /
• 제22권1호
• /
• pp.97-104
• /
• 2013

This study aims at finding out the characteristics and influences of Libeskind's early drawing works through comparisons of each drawing. The importance of his experimental drawing works is not only their uniqueness but also relationship to creation and development of his architecture. Libeskind's musical and educational background had great impacts on forming his early drawings. A series of drawings including 'Micromegas', 'Chamberworks', and 'Theatrum Mundi' shows variety and experiments about reconstruction of three dimensional architectural fragments, abstractive line drawing and plane oriented painting. Libeskind himself cease to experiment drawing techniques but their characteristics still remain in his sketches, diagram and conceptual drawings. In spite of influences of undergraduate design studios, theoretical background of graduate studies, their experimental features are due to his continuous endeavor to make and develop his drawing skills and contents. As a result, his early drawings act as media and way to communicate and develop his concepts.

• 소성∙가공
• /
• 제6권4호
• /
• pp.300-310
• /
• 1997

A finite element inverse method is introduced for direct prediction of blank shapes, strain distributions, and reliable intermediate shapes from desired final shapes in axisymmetric multi-step deep drawing processes. This mothod enables the determination of process disign. The approach deals with the Hencky's deformation theory. Hill's second order yield criterion, simplified boundary conditions, and minimization of plastic work with constraints. The algorithm developed is applied to motor case forming, and cylindrical cup drawing with the large limit drawing ratio so that it confirms its validity by demonstrating resonably accurate numerical results of each problem. Numerical examples reveal the reason of difficulties in motor case forming with corresponding limit diagrams.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2000년도 추계학술대회
• /
• pp.31-35
• /
• 2000

We investigate the groundwater distribution and chemical characteristics for 3 or 5 districts every year and make the hydrogeologic map on a scale of 1:50,000. We draw the hydrogeologic digital map based on "The Handbook for the Drawing and Management of Hydrogeologic Map" which was published by MOCT and KOWACO in 1998. But, the Stiff diagram and well's notation are difficult to be presented in the digital map using the commercial Arcview GIS tools. So we develop the script file with Avenue language to represent them in Arcview GIS tool. At first, we design the database for the chemical analysis result of groundwater and well identification, and make the program code with Avenue language to display them on the digital map. And next we test the usefulness of the program code. As a result, we find that the script file is very useful for drawing the symbols and diagrams in hydrogeologic digital map using ArcView GIS.