• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.3
• /
• pp.219-227
• /
• 2021

Numerical simulation with Hwang's scheme, which can analyze shallow-water flow over discontinuous topography, was compared with a laboratory experiment of flooding on a perpendicular floodplain with dam-break flows. The simulation results were in good agreement with the results measured in an experimental flume with a reservoir, channel, and floodplain. The wetting and drying process on a perpendicular floodplain with a dam-break flow was particularly well simulated. The difference in simulation results according to the type of flow resistance was insignificant. The results of this study are expected to improve the accuracy of predicting inundation in urban rivers.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.5
• /
• pp.277-284
• /
• 2023

Hardness and damping characteristics of fine discontinuous precipitates (DPs) microstructure generated by low temperature long term isothermal aging were investigated in comparison with those of T6 heat-treated microstructure composed of DPs and continuous precipitates (CPs) in Mg-9%Al alloy. In this study, T6 and fine DPs microstructures were obtained by isothermal aging at 453 K for 24 h and at 413 K for 336 h, respectively, after solution treatment at 693 K for 24 h. The DPs microstructure exhibited higher hardness than the T6 microstructure, which is related to the lower (α + β) interlamellar spacing of the DPs. The DPs microstructure possessed better damping capacity than the T6 microstructure in the strain-amplitude independent region, whereas in the strain-amplitude dependent region, the reverse behavior was observed. The damping tendencies depending on strain-amplitude were discussed based on the microstructural features of the T6 and DPs microstructures.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.769-779
• /
• 2023

This paper describes an hp-angular adaptivity algorithm in the discrete ordinates method for Boltzmann transport applications with strong angular effects. This adaptivity uses discontinuous finite element quadrature sets with different degrees, which updates both angular mesh and the degree of the underlying discontinuous finite element basis functions, allowing different angular local refinement to be applied in space. The regular and goal-based error metrics are considered in this algorithm to locate some regions to be refined. A mapping algorithm derived by moment conservation is developed to pass the angular solution between spatial regions with different quadrature sets. The proposed method is applied to some test problems that demonstrate the ability of this hp-angular adaptivity to resolve complex fluxes with relatively few angular unknowns. Results illustrate that a reduction to approximately 1/50 in quadrature ordinates for a given accuracy compared with uniform angular discretization. This method therefore offers a highly efficient angular adaptivity for investigating difficult particle transport problems.

• Transactions of Materials Processing
• /
• v.32 no.2
• /
• pp.53-60
• /
• 2023

A wide range of grain size was achieved in a Fe-Cr-Mn austenitic stainless steel (STS) by cold rolling and reversion annealing. The tensile characteristics of the STS were analyzed in terms of the dependence of strain induced martensitic (SIM) transformation on the grain size. In the ultrafine grain regime, the steel showed a high yield strength over 1 GPa, a discontinuous yielding, and a prolonged yield point elongation followed by considerable strain hardening. By increasing the grain size, the discontinuous yielding diminished and the yield point elongation decreased. The microstructural examination revealed that these tensile characteristics are closely related to the suppression of SIM transformation with decreasing the grain size. Especially, the prolonged yield point elongation of the ultrafine grained STS was found to be associated with development of unidirectional ε martensite bands. Based on the microstructural examination of the deformed microstructures, the rationalization of the grain size dependence of SIM transformation was suggested.

• Korean Chemical Engineering Research
• /
• v.62 no.2
• /
• pp.191-199
• /
• 2024

A study was conducted on a tubular heat exchanger to improve its heat transfer rate by using a novel baffle plate design with discontinuous swirling patterns. The design consisted of perforated baffle plates with rectangular air deflectors positioned at varying angles. The tubes in the heat exchanger were arranged in a consistent alignment with the airflow direction and exposed to a uniform heat flux on their surfaces. Each baffle plate included sixteen deflectors inclined at the same angle and arranged in a clockwise pattern. This arrangement induced a swirling motion of the air inside a circular duct where the heated tubes were located, leading to increased turbulence and improved heat transfer on the tube surfaces. The spacing between the baffle plates was adjusted at different pitch ratios, and the Reynolds number was controlled within a range of 16,000 to 29,000. The effects of pitch ratios and inclination angles on the heat exchanger's performance were analyzed. The results indicated that using a baffle plate with rectangular deflectors inclined at 30° and a pitch ratio of 1.2 resulted in an average increase of 1.29 in the thermal enhancement factor.

• Journal of Biomedical Engineering Research
• /
• v.33 no.2
• /
• pp.72-77
• /
• 2012

Phase Contrast MR Angiography(PC MRA) is excellent MRA technique for measuring the velocity of vessels in the human body. PC MRA need to at least four images for angiogram reconstruction and it caused longer scan time. Therefore, we used keyhole imaging combined PC MRA to reduce the scan time. However, keyhole imaging can lead the erroneous effects as loss of phase information or frequency discontinuous. In this study, we applied the keyhole imaging combined 2D PC MRA for improving the temporal resolution and also measured the velocity to evaluate the accuracy of phase information. We used 0.32T MRI scanner(Magfinder II, Scimedix, Korea). Using the 2D PC MRA pulse sequence, the vascular images for a human brain targeted on the Superior Sagittal Sinus(SSS) were obtained. We applied tukey window function for keyhole images to minimize the ringing artifact and erroneous factors that are induced frequency discontinuous and phase information loss. We also applied zero-padded algorithm to peripheral missing k-space lines to compare keyhole imaging results and the artifact power(AP) value was measured on the complex difference images to validate the image quality. Consider as based on our results, heavy image distortions and artifacts were shown until using at least 50% keyhole factor. Using above the 50% keyhole factors are shown well reconstructed and matched for magnitude images and velocity information measurements. In conclusion, we confirmed the image quality and velocity information of keyhole technique combined 2D PC MRA. Especially, measured velocity information through the keyhole imaging combination was similar to the velocity information of full sampled k-space image despite of frequency discontinuous and phase information loss in the keyhole imaging reconstruction process. Consequently, the keyhole imaging combined 2D PC MRA will give some clinical usefulness and advantages as improving the temporal resolution and measuring the velocity information via selecting the appropriate keyhole factor at low tesla MRI system.

• The Journal of Engineering Geology
• /
• v.2 no.1
• /
• pp.1-18
• /
• 1992

Rock mass having discontinuous plane almost appear roughness which have a great effect on shear strength. Rocks of studied object choose granites (15 samples), gneisses (7 samples), and andesites (1 sample). The purpose of this study was to clarify shear strength of discontinuous planes as value of shear strength angle (${\Phi}_p$), critical stress of roughness (${\sigma}_r$) and shear failure strength (${\tau}_o$). 1. Roughness decrease from ${\Phi}_i=38.03^{\circ}$ to $33.21^{\circ}$ that is, friction angle has the highest value at first stage and has the lowest value at the last stage. 2. Critical angle of roughness distribution within $45^{\circ}$ (test max. $angle=43^{\circ}$), JRC(Joint Roughness Coefficient) is less than 14 and lies distribution range of boundary is following: $JRC=-4.63Ln{\sigma}n+5.63$. 3. When the roughness critical stress(${\sigma}_T) is from 0.1 to 3 .56Mpa, shear failure strength of roughness (${\tau}_o$) is from 0.01 to 0.46Mpa, shear strength(${\tau}$) of discontinuous plane is from 3.65 to 39.11 Mpa. If loading is higher than these values, collapse and sliding will occur on the rock mass.

• Economic and Environmental Geology
• /
• v.40 no.6
• /
• pp.751-759
• /
• 2007

To better understand the subsurface geological structure of the Kunsan Basin in the Yellow Sea, the mean depths of the density discontinuous layers (DDLs) of the Kunsan Basin were calculated by power spectrum analysis using satellite altimetry gravity data. The calculated mean depths of DDLs were -1.1km, -3.4km, -9.1km and -31.0km. The mean depth of -1.1km DDL was interpreted as regional unconformity shown in about 1 second in two way travel time (TWTT) in the seismic reflection profiles, and the mean depth of -3.4km DDL was also interpreted as top of the acoustic basement in the seismic reflection profiles. Comparing with well data, seismic reflection profiles and regional geology in the study area, the mean depth of -9.1km DDL was interpreted as top of the igneous origin basement. This means that the acoustic basement of the study area is composed mainly of sediments which are disregarded in previous study. The mean depth of -31.0km DDL was interpreted as the Moho discontinuity because this mean depth is similar to one of the normal continental crust thickness. The detection of top of the igneous origin basement suggests that oil gas potential analysis in Kunsan Basin needs to be extended to the deeper part of sediments (acoustic basement).

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.5
• /
• pp.249-254
• /
• 2014

In this paper, minimizing of a parabolic edge planar monopole antenna by scaling method is presented. With the aid of a matching step and discontinuous CPW, the antenna easily adjusts the impedance matching. We used an FR4 dielectric substrate with a dielectric constant of 4.4. The dimensions of the antenna are $26mm{\times}31mm{\times}1.6mm$. A return loss value of more than 10dB was found in the 2.37GHz to 10.52GHz (8.15GHz) range of the antenna fed by the discontinuous CPW. The radiation pattern is about the same as that of the dipole antenna at all frequencies. Configuration elements of the antenna except feed part were reduced into the same rate. So, the size of the antenna was decreased and a broadband property was maintained. Therefore, the self-complementary characteristic of the antenna was confirmed. While satisfying the UWB band, having the smallest size in the antenna miniaturized by scaling;when scale was 0.6. The dimensions of the antenna are $15.6mm{\times}18.6mm{\times}1.6mm$. The return loss was more than 10 dB of the measured result in the range of 3.07GHz to 12.59GHz (9.52GHz).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.24 no.6
• /
• pp.459-471
• /
• 1991

The community structure and micro-scale distribution of plankton in relation to hydrography were investigated in Masan Bay, Korea in October 1989. Warmer and less saline waters with stratification was located in the inner part of the Pudo Strait, and chlorophyll-a and nutrients were higher. Both phytoplankton biomass and nutrients was changed dramatically around the Strait. Offshore/oceanic species in phytoplankton i.e., Chaetoceres decipiens, Rhizosolenia stolterforthii, Rhizosolenia styliformis and Ceratium trichoceros and zooplankton i.e., Sagitta enflata, Oncaea uenusta and Oikopluera longicaudata occurred mainly in well mixed waters of the outer part. This suggests that discontinuous layer seems to play an important role as an approximate border for the plankton population. This layer was located between Station 3 and Station 4 near the Pudo Strait, since the layer consisted of a series of micro-scale discontinuties of salinity and dissolved inorganic nutrients gradient. Phytoplankton patchs of more than 801e1 were found only in the inner part of the bay. Depletion of silicate caused by a rapid assimilation of phytoplankton in the inner part of the bay seemed to be responsible for the decline of blooms.