• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.5
• /
• pp.324-333
• /
• 2013

Recently, rudder erosion due to cavitation has been frequently reported on a semi-spade rudder of a high-speed large ship. This problem raises economic and safety issues when operating ships. The semi-spade rudders have a gap between the horn/pintle and the movable wing part. Due to this gap, a discontinuous surface, cavitation phenomenon arises and results in unresolved problems such as rudder erosion. In this study, we made a rudder model for 2-D experiments using the NACA0020 and also manufactured gap flow blocking devices to insert to the gap of the model. In order to study the gap flow characteristics at various rudder deflection angles($5^{\circ}$, $10^{\circ}$, $35^{\circ}$) and the effect of the gap flow blocking devices, we carried out the velocity measurements using PIV(Particle Image Velocimetry) techniques and cavitation observation using high speed camera in Seoul National University cavitation tunnel. To observe the gap cavitation on a semi-spade rudder, we slowly lowered the inside pressure of the cavitation tunnel until cavitation occurred near the gap and then captured it using high-speed camera with the frame rate of 4300 fps(frame per second). During this procedure, cavitation numbers and the generated location were recorded, and these experimental data were compared with CFD results calculated by commercial code, Fluent. When we use gap flow blocking device to block the gap, it showed a different flow character compared with previous observation without the device. With the device blocking the gap, the flow velocity increases on the suction side, while it decreases on the pressure side. Therefore, we can conclude that the gap flow blocking device results in a high lift-force effect. And we can also observe that the cavitation inception is delayed.

• Korean journal of food and cookery science
• /
• v.15 no.5
• /
• pp.500-506
• /
• 1999

Scanning electron microscopy was used to study changes in granule shape, dough and cooked noodle structure of pea starch-wheat composite flour with 20% and 30% pea starch substitution. The granule shape of pea starch with low swelling power and solubility was oval, irregular and smooth, which had more a deep groove than corn starch and wheat flour. During gelatinization, pea starch after swelling was partially collapsed but it still held its main shape. The dough microstructure of 20% pea starch substitution showed compact structure distributed with more small starch granules than wheat dough and was held in discontinuous network. When cooked, more open filamentous network where starch gelatinization was complete were noticed. Swollen but partially collapsed large starch granules maintaining their shape were appeared in noodle structure after 30 min soaking in soup. In farinograph studies, 20% pea starch substitution to wheat flour showed that MTI value was as same as wheat flour even though stability was slightly decreased so that it was considered that it has proper property of noodle making.

• The Korean Journal of Pain
• /
• v.22 no.2
• /
• pp.158-162
• /
• 2009

Background: The loss of resistance (LOR) method is most commonly used to identify the epidural space. This method is thought to rely on the penetration of the ligamentum flavum. Unfortunately the exact morphology of the ligamentum flavum is variable at different vertebral levels. Especially, it has been pointed out that the lower cervical ligamentum flavum may be discontinuous in the midline in up to 50% of patients. Thus, the LOR method may be inaccurate to confirm the cervical epidural space. The aim of this study is to determine which method is the safest and most exact for confirming the cervical epidural space. Methods: 100 adult, chronic renal failure patients who were undergoing an arteriovenous bridge graft for hemodialysis at the upper arm under cervical epidural anesthesia were recruited for this study. During the cervical epidural puncture, we identified the cervical epidural space by subjectively feeling the resistance with using a finger just through the ligamentum flavum, and we also used the drip infusion method, the loss of resistance method using air, and the hanging drop method. By using 5 grades, we classified the extent of whether or not the techniques were effective. Results: Using the drip infusion method, we identify the epidural space in all the patients as ＋/＋＋ grade. The catheter insertion method was also successful in identifying those epidural spaces over a ${\pm}$ grade. The pseudo LOR was over ${\pm}$ grade in 47 patients. Conclusions: The combined LOR/hanging drop with drip infusion method is useful for confirming the cervical epidural space.

• Journal of the Korean association of regional geographers
• /
• v.13 no.6
• /
• pp.623-638
• /
• 2007

This paper debates on two different theoretical positions in explaining corporate adaptation. Until the 1980s, a restructuring perspective had dominated in explaining corporate success and adaptation. However, this perspective pays little attention to how firms adapt to environmental change and why some firms adapt successfully, while some others fail to adapt. Thus a restructuring perspective does not give insights into a context-specific explanation of corporate learning and adaptation. More recently, especially since the 1990s, academic focus on corporate adaptation and evolution has shifted towards exploring the nature of learning that leads to the dynamic competitiveness. A learning perspective emphasizes the influence of knowledge, learning and competence on corporate evolution. However, it reveals that this view is also less appropriate for explaining corporate adaptation in radical shifts in environment. In this context, the evolutionary theories of the firm need to seek to maintain a balance between two theoretical positions in order to understand more effectively the dynamic evolution and adaptation of the firm. This paper shows that the dynamics of corporate adaptation and evolution are an outcome of the mixture of perpetual processes of restructuring and learning, both continuous and discontinuous.

• 한국문화재보존과학회:학술대회논문집
• /
• 2004.10a
• /
• pp.15-24
• /
• 2004

The Seokgatap pagoda composed of mainly alkali granite and other minor pink-feldspar granite, fine-grained granite, granodiorite, diorite, gabbro, and tuff. Despite the small loss and damage derived from joints, its peel-off and exfoliation are serious enough to cause the heavy deterioration on the stone surface. The chemical and petrological weathering has partly replaced the original rock-forming minerals with clay minerals and iron oxyhydroxides. Based on the petrogenesis, rock materials of the pagoda is very similar to rocks of Dabotap pagoda and the Namsan granite in the Gyeongju. The central fart of the pagoda has sunken highly, which caused all the corners to split and the structural transformation to become worse. The reverse V-shaped gaps between the materials have broken stones filled in a coarse way. The iron plates inserted between the upper flat stone laid on other stones and tile pagoda body in the north and east side has been exposed in the air and corroded, discoloring of the adjacent stones. The overall diagnosis of the Seokgatap pagoda is the deteriorated functions of the stone materials, which calls for a long-term monitoring and plans to reinforce the stone surfaces. But the main body including the pagoda roof stone needs washing on a regular basis, and the many different cracks should be fixed with glue by using the fillers or hardeners designed for stone cultural properties after removing the cement mortar. In case of the replacement of the stone materials with new stones, it's necessary to examine the pagoda for the center of gravity and support intensity of the materials. The structural stability of the pagoda can be attained by taking a reinforce measure in geotechnical engineering and making a drainage. The ground humidity, which has aggravated weathering and structural instability, should be resolved by setting up a humidity reduction facility. The contamination of lichens and bryophyte around the pagoda and on the surface is serious. Thus biochemical treatments should be given too in order to prevent further biological damages and remove the vegetation growing on the discontinuous planes.

• Journal of Conservation Science
• /
• v.28 no.1
• /
• pp.39-52
• /
• 2012

The Usuki Stone Buddha Statues in Oita are consisted of 60 Buddhas which represent of Japan carved on the rock-cliff in the 12 to 14th centuries. The basement rock of the statues is dark gray welded lapilli tuff that containing the Aso-4 pyroclastic rock group. Deterioration maps for the Hoki I and the Furuzono Buddha Statues group show multi-directional fissures on the Cakra, and sheeting-off zone at the margin of uprising water. Deterioration rate of the Hoki I group was calculated fissure about 121 in number, 19% of sheeting-off zone and 51% of biological weathering in surface of area. And the Furuzono group was also evaluated as about 48 of fissures in number, 24% of sheeting-off zone and 41% biological weathering. The slope stability assessment results, the Hoki I developed discontinuous planes has possibility of planar, toppling and wedge failures in all caves. Ultrasonic velocity of the Aizen-myooh (basement rock) ranges from 1,520 to 2,794 (average 2,298m/s). And pedestal of Amita-yeorae which has been replaced by new fresh rock is measured as 3,242 to 4,141 (average 3,813m/s). Therefore, we establish of planing conservation treatment and reinforcement methods to fissure, cavity, sheeting-off zone in the Buddha surface.

• The Korean Journal of Physiology
• /
• v.20 no.2
• /
• pp.257-270
• /
• 1986

It has been reported that the luteal function may be regulated by the intracellular calcium in luteal cells (Higuchi et al, 1976; Dorflinger et at, 1984; Gore and Behrman, 1984) which is adjusted partially by $Ca^{++}-ATPase$ activities in luteal cell membranes (Verma and Pennistion, 1981). However, the physicochemical and kinetic properties of $Ca^{++}-ATPase$ in luteal membranes were not fully characterized. This study was, therefore, undertaken to partially characterize the physicochemical and kinetic properties of $Ca^{++}-ATPase$ system in luteal membranes and microsomal fractions, known as an one of the major $Ca^{++}$ storge sites (Moore and Pastan, 1978), from the highly luteinized ovary Highly luteinized ovaries were obtained from PMSG-hCG injected immautre female rats. Light membrane and heavy membrane fractions and microsomal fractions were prepared by the differential and discontinuous sucrose density gradient centrifugation method desribed by Bramley and Ryan (1980). Light membrane and heavy membrane fractions and microsomal fractions from highly luteinized ovaries are composed of the two different kinds of $Ca^{++}-ATPase$ system. One is the high affinity $Ca^{++}-ATPase$ which is activated in low $Ca^{++}$ concentration (Km, 10-30 nM), the other is low affinity $Ca^{++}-ATPase$ activated in higher $Ca^{++}$ concentration $(K_{1/2},\;40\;{\mu}M)$. At certain $Ca^{++}$ concentrations, activities of high and low affinity $Ca^{++}-ATPase$ are the highest in light membrane fractions and are the lowest in microsomal fractions. It appeares that high affinity $Ca^{++}-ATPase$ system have 2 binding sites for ATP (Hill's coefficient; around 2 in all membrane fractions measured) and the positive cooperativity of ATP bindings obviously existed in each membrane fractions. The optimum pH for high affinity $Ca^{++}-ATPase$ activation is around S in all membrane fractions measured. The lipid phase transition temperature measured by Arrhenius plots of high affinity $Ca^{++}-ATPase$ activity is around $25^{\circ}C$. The activation energies of high affinity $Ca^{++}-ATPase$ below the transition temperature are similar in each membrane fractions, but at the above transition temperature, it is the hightest in heavy membrane fractions and the lowest in microsomal fractions. According to the above results, it is suggested that intracellular $Ca^{++}$ level, which may regulate the luteal function, may be adjusted primarily by the high affinity $Ca^{++}-ATPase$ system activated in intracellular $Ca^{++}$ concentration range $(below\;0.1\;{\mu}M)$.

• Korean Journal of Child Studies
• /
• v.1
• /
• pp.94-106
• /
• 1980

The issue presented in this paper are as follows: 1. Legislative actions of welfare-related law for the exceptional children. The legislative base for the evolution has been yet weak and ambigous at best for a formalization of what should be considered accepted practice and effective action in providing handicapped child and their parents educational rights and equal protection of the law. And they are under remote control of partial factor subject to social welfare law for children, and public law for education, promotion law for the exceptional child education, protection law for public aids. 2. Organization of government for the welfare services for the exceptional children. There is no sing of a push toward consolidation of effort for the welfare service of the exceptional children in this country that seeks to recapture a sense of unity, of coherence, of completeness from a reality made up of discontinuous fragments of humanitarian effora This presently that. as for the education of the exceptional child, by the section of the exceptional education in MOE (Ministry of Education), and/or as for welfare services and promotion actions, by the section of child welfare in MHSA (Ministry of Health and Social Affairs). One door type operation rooted in the specialization, and limited resources to evolve multi-purpose agencies that undertake to provide a broad range of tangible and concrete services, as well as supportive counselling and assessment, under a single management which plans and directs the allocations of resources, should be followed. 3. Facilities and recruitment of teachers for the exceptional children. In this country there are 54 facilities for special services, 56 schools for the exceptional education, and 3 colleges and equavalents that provide teacher training services leading to certification with IIO annual graduates. However, curriculum for exceptional children should be rearranged and reconstructed. Conclusion; Only as for social welfare institutions in community, this country produced a succession of specific purpose activities, over period of time, that accumulated to form the present network of hundreds of social welfare organizations and facilities Periodically major efforts were launched to revitalize or to improve the help-giving system. But they lack specialization to be effective, and the nature of multi-purpose center tends to be vague for the classified handicapped. Therefore, there, should be linkage between policy maker and community services to maintain some coherenty in preventive care, treatment, and after cares. At last, the effects of the current concept "the exceptional child" involved with their families, and their neighborhood should be considered in view of the people who consist about 25% of the total population.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1084-1096
• /
• 2016

This paper presents method of design and analysis of a high-speed serial interface connector with a data rate of 12.5 Gbps. A high-speed serial interface connector is composed of various material and complex structures. It is very difficult to match the impedance of each discontinuous portion of connector. Therefore, this paper proposes the structure of a connector line that be simplified a connector. In the structure of proposed connector line, this research presents a method for extracting R, L, C and G parameters, analyzing the differential mode impedance, and minimizing the impedance discontinuity using time domain transmissometry and time domain reflectometry. This paper applies the proposed methods in the connector line to the high-speed serial interface connector. The proposed high-speed serial interface connector, which consists of forty-four pins, is analyzed signal transmission characteristics by changing the width and spacing of the four pins. According to the analysis result, as the width of the ground pin increases, the impedance decreases slightly. And as the distance between the ground pin and the signal pin increases, the impedance increases. In addition, as the width of the signal pin increases, the impedance decreases. And as the distance between the signal pin and the signal pin increases, the impedance decreases. The impedance characteristic of initial connector presents ranges from 96 to $139{\Omega}$. Impedance characteristic after applying the structure of proposed connector is shown as a value between 92.6 to $107.5{\Omega}$. This value satisfies the design objective $100{\Omega}{\pm}10%$.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.3
• /
• pp.444-456
• /
• 2000

To test the shear bond strength of a new "one-bottle adhesive" system to primary dentin two commercially available one-bottle adhesives (Prime & Bond NT, Single bond) and conventional three step system(Scotchbond Multi-Purpose Plus) were included for comparison. And We observe the interfacial morphology by scanning electron microscope. 90 primary molar teeth were embedded in acrylic and buccal and lingual surface were polished to 320 grit to create standardized dentin surface for testing. After bonding of composite resin to sample surfaces according to the manufacturer s direction and 1000 times thermocycling in dwell time 30 second, Shear bond strengths of adhesives to dentin were determined using universal testing machine and analyzed by ANOVA test. Another groups of specimens were treated by hydrochloric acid to secure the resin only and those tags were evaluated under SEM for their length and forms and the morphology of the bonding sites were also observed. The result are as follows. 1. Group I(Prime & Bond NT) showed higher shear bond strength than group iI(Single Bond) and III(Scotchbond Multi Purpose Plus) but no statistically significant difference was founded between groups(p>.05). 2. Relating long resin tags of $70-120{\mu}m$ were observed in samples of all groups under SEM. We could observed hybrid layer, resin tag and many lateral branches in every group. But, we observed in group III rare lateral branched than other two group and discontinuous hybrid layer.