• Journal of the Korean Geotechnical Society
• /
• v.26 no.2
• /
• pp.55-62
• /
• 2010

This paper investigates the shear properties of waste tire-bottom ash mixture with various particle size of waste tire powder. Test specimens were prepared at 5 different percentages of waste tire powder content (i.e., 0%, 25%, 50%, 75%, 100% by weight of the dry bottom ash), and with three different particle sizes of waste tire powder (i.e., 0.1 mm~2.0 mm, 0.9 mm~5 mm and 2 mm~10 mm). In this study several series of direct shear tests were carried out. The experimental results indicate that the mechanical characteristics of waste tire-bottom ash mixture are strongly influenced by the particle size as well as waste tire powder content. It is shown that the shear strength and internal friction angle of waste tire-bottom ash mixture decrease with an increase in waste tire powder content. However, the shear strength and internal friction angle of the mixture increase due to interlocking effect between waste tire powder and bottom ash as the particle size of waste tire powder increases.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.18 no.4
• /
• pp.12-21
• /
• 2022

Steam assisted gravity drainage(SAGD) is a process that drills well in the underground oil sands layer, injects hightemperature steam, lowers the viscosity of buried bitumen, and recovers it to the ground. Recently, direct contact steam generator(DCSG) is being developed to maximize steam efficiency for SAGD process. The DCSG requires high technology to achieve pressurized combustion and steam generation in accordance with underground pressurized conditions. Therefore, it is necessary to develop a combustion technology that can control the heat load and exhaust gas composition. In this study, process analysis of high-pressurized DCSG was conducted to apply oxygen enrichment technology in which nitrogen of the air was partially removed for increasing steam production and reducing fuel consumption. As the process analysis conditions, methane as the fuel and normal air or oxygen enriched air as the oxidizing agent were applied to high-pressurized DCSG process model. A simple combustion reaction program was used to calculate the property variations for combustion temperature, steam ratio and residual heat in exhaust gas. As a major results, the steam production efficiency of DCSG using the pure oxygen was about 6% higher than that of the normal air due to the reducing nitrogen in the air. The results of this study will be used as operating data to test the demonstration device.

• Journal of Korea Trade
• /
• v.26 no.3
• /
• pp.45-62
• /
• 2022

Purpose - Using unexpected changes in geopolitical tensions on the Korean peninsula as a quasi-natural experimental setting, we examine whether and how geopolitical risks travel across borders through firm-level imports and exports linkages. We also test whether the effects are driven by either imports or exports and assess whether firms can effectively hedge themselves against geopolitical risks. Design/methodology - We focus on a series of unanticipated geopolitical events taken place in Korea in 2018. Making use of the shocks to geopolitical climate, we identify five milestone events toward peace talks. We employ the event studies methodology. We examine heterogenous firm-level stock price reactions around key event dates depending on firms' exposure to geopolitical risks. As a measure of firms' exposure to geopolitical risks in Korea, we utilize a text-based measure of firm-level trade links. When a firm announces and discusses its purchase of inputs from Korea or sales of outputs to Korea in their annual disclosure filings, we define a firm to have a trade relationship with Korea and have exposure to Korean geopolitical risks. Similarly, we use a measure of a firm's hedging policies based on a firm's textual mention of the use of foreign exchange derivatives in their annual disclosure. Findings - We find that U.S. firms that have direct trade links to Korea gained significantly more value when the intensity of geopolitical risks drops compared to firms without such trade links to Korea. The effects are pronounced for firms purchasing inputs from or selling outputs to Korea. We find that the effectiveness of foreign exchange hedging against geopolitical risks is limited. Originality/value - We document the international transmission of geopolitical uncertainty through trade linkages. Export links as well as import links serve as important nexus of transmission of geopolitical risks across borders. Hedging strategies involving foreign-exchanges derivatives do not seem to insulate firms again geopolitical risks. With the recent movements of localization and reshuffling of the global value chain, our results suggest a significant impact of geopolitical risks in Korea on the construction of the global value chain.

• Journal of Digital Convergence
• /
• v.20 no.1
• /
• pp.399-414
• /
• 2022

The purpose of this study was to test the structural model for the effect on abnormal eating behavior targeting 493 nurses. Results, The direct effects of variables affecting abnormal eating behavior were in the order of eating abstinence and socially imposed perfectionism, and these variables explained 85% of abnormal eating behavior. Explicit narcissism had a significant effect on abnormal eating behavior through socially imposed perfectionism and eating restraint, and sociocultural attitude toward appearance through eating restraint. In the multi-group moderating effect, the path coefficients between job stress and abnormal eating behavior, socially imposed perfectionism and abnormal eating behavior were different between groups. Therefore, it is necessary to find a way to lower the socially-imposed perfectionism and nursing intervention that can escape excessive eating abstinence.

• Restorative Dentistry and Endodontics
• /
• v.46 no.4
• /
• pp.60.1-60.8
• /
• 2021

Objectives: The aim of this study was to verify the match between 5 shades of composites from different manufacturers with a shade guide and among the systems using a portable spectrophotometer. Materials and Methods: Shade measurements were performed on specimens of Z350 XT (3M ESPE), Charisma Diamond (Heraeus Kulzer GmbH), Esthet X-HD (Dentsply Caulk), and Empress Direct (Ivoclar-Vivadent) for shades A1, A2, A3, B1, and C3 using a Vita Easyshade spectrophotometer (Vita Zahnfabrik) against a white background. Corresponding shades of Vitapan Classical (Vita Zahnfabrik) guide were measured likewise and shade variation (ΔE) was calculated based on International Commission on Illumination L^*a^*b^* parameters. The ΔE of the composites in each shade was compared by one-way analysis of variance and Tukey's post hoc test (α = 0.05). Results: All composites presented ΔE > 3.7 compared with the shade guide. Variation in shades A3, B1, and C3 was significantly different for all composites. ΔE of Z350 XT was significantly lower for A1 than for the other shades, whereas ΔE of Z350 XT and Charisma Diamond were significantly lower for A2 than for the other shades. Conclusions: No composite shade matched with the shade guide. Equivalent shades of the restorative composite from different manufacturers may show clinically noticeable ΔE.

• Restorative Dentistry and Endodontics
• /
• v.46 no.2
• /
• pp.29.1-29.11
• /
• 2021

Objectives: This study was conducted to compare the post-fracture survival rate of endodontically treated molar endodontically treated teeth (molar ETT) restored with resin composites or crowns and to identify potential risk factors, using a retrospective cohort design. Materials and Methods: Dental records of molar ETT with crowns or composite restorations (recall period, 2015-2019) were collected based on inclusion and exclusion criteria. The incidence of unrestorable fractures was identified, and molar ETT were classified according to survival. Information on potential risk factors was collected. Survival rates and potential risk factors were analyzed using the Kaplan-Meier log-rank test and Cox regression model. Results: The overall survival rate of molar ETT was 87% (mean recall period, 31.73 ± 17.56 months). The survival rates of molar ETT restored with composites and crowns were 81.6% and 92.7%, reflecting a significant difference (p < 0.05). However, ETT restored with composites showed a 100% survival rate if only 1 surface was lost, which was comparable to the survival rate of ETT with crowns. The survival rates of ETT with composites and crowns were significantly different (97.6% vs. 83.7%) in the short-term (12-24 months), but not in the long-term (> 24 months) (87.8% vs. 79.5%). Conclusions: The survival rate from fracture was higher for molar ETT restored with crowns was higher than for ETT restored with composites, especially in the first 2 years after restoration. Molar ETT with limited tooth structure loss only on the occlusal surface could be successfully restored with composite restorations.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2019.10a
• /
• pp.83-83
• /
• 2019

Increasing the CO₂ concentration in the atmosphere induce high temperature and rising sea levels. So the technology that capture and reuse of the CO₂ have been recently become popular. Among other methods, CRR(CO2₂ reduction reaction) is typical method of CO₂ reusing. Electrocatalyst can show more higher efficiencies in CRR than photocatalyst because it doesn't use nature source. Nowadays, finding high efficient electrocatalyst by controlling electronic (affected by stoichiometry) and geometric (affected by atomic arrangement) factors are very important issues. Mono-atomic electro-catalyst has limitations on controlling binding energy because each intermediate has own binding energy range. So the Multi-metallic electro-catalyst is important to stabilize intermediate at the same time. Carbon monoxide(CO) which is our target product and important feedstock of useful products. Au is known for the most high CO production metal. With copper, Not only gold/copper has advantages which is they have FCC packing for easily forming solid solution regardless of stoichiometry but also presence of adsorbed CO on Cu promotes the desorption of CO on Au because of strong repulsion. And gold/copper bi-metal catalyst can show high catalytic activity(mass activity) although it has low selectivity relatively Gold. Actually, multi-metallic catalyst structure control method is limited in the solution method which is takes a lot of time. In here, we introduce CTS(carbo thermal shock) method which is using heat to make MMNP in a few seconds for making gold-copper system. This method is very simple and efficient in terms of time(very short reaction time and using carbon substrate as a direct working electrode) and increasing reaction sites(highly dispersed and mixing alloy structures). Last one is easy to control degree of mixing and it can induce 5 or more metals in one alloy system. Gold/copper by CTS can show higher catalytic activity depending on metal ratio which is altered easily by changing simple variables. The ultimate goals are making CO₂ test system by CTS which can check the selectivity depending on metal types in a very short time.

• Smart Media Journal
• /
• v.12 no.1
• /
• pp.17-23
• /
• 2023

Design-For-Security (DFS) methodology is to protect integrated circuits from physical attacks, and that can be implemented by adding a security circuit to detect abnormal external access. Among the abnormal accesses called invasive attack, microprobing and FIB circuit editing are classified as the most powerful methods because they have direct access. Microprobing deliberately inject defects into the wire of circuit through probes, or reads and changes data. FIB circuit editing is methods of reconnecting or destroying circuits to neutralize security circuits or to access data. Previous DFS methodology have responded to the attacks by detecting arrival time asymmetry between the two signals or by comparing input/output data based on encrypted communication. This study conducted to reduce hardware overhead, and the proposed circuit detects the reflected signal asymmetry generated through probe or FIB circuit editing and detects the attacks through comparison. Since the proposed security circuit reduces the size and test cycle of the circuit compared to previous studies, the cost used for security can be reduced.

• Steel and Composite Structures
• /
• v.42 no.1
• /
• pp.1-22
• /
• 2022

In cold-formed steel (CFS) structures, such as trusses, transmission towers and portal frames, the use of back-to-back built-up CFS unequal angle sections are becoming increasingly popular. In such an arrangement, intermediate welds or screw fasteners are required at discrete points along the length, preventing the angle sections from buckling independently. Limited research is available in the literature on axial strength of back-to-back built-up CFS unequal angle sections. The issue is addressed herein. This paper presents an experimental investigation reported by the authors on back-to-back built-up CFS unequal angle sections with intermediate stiffeners under axial compression. The load-axial shortening behaviour along with the deformed shapes at failure are reported. A nonlinear finite element (FE) model was then developed, which includes material non-linearity, geometric imperfections and modelling of intermediate fasteners. The FE model was validated against the experimental test results, which showed good agreement, both in terms of failure loads and deformed shapes at failure. The validated finite element model was then used for the purpose of a parametric study comprising 96 models to investigate the effect of longer to shorter leg ratios, stiffener provided in the longer leg, thicknesses and lengths on axial strength of back-to-back built-up CFS unequal angle sections. Four different thicknesses and seven different lengths (stub to slender columns) with three overall widths to the overall depth (B/D) ratios were investigated in the parametric study. Axial strengths obtained from the experimental tests and FE analyses were used to assess the performance of the current design guidelines as per the Direct Strength Method (DSM); obtained comparisons show that the current DSM is conservative by only 7% and 5% on average, while predicting the axial strengths of back-to-back built-up CFS unequal angle sections with and without the stiffener, respectively.

• The Journal of Information Systems
• /
• v.32 no.1
• /
• pp.23-51
• /
• 2023

Purpose: Live commerce is a new type of electronic commerce in combination with live streaming services. It is expected to increase virtual presence in the context of online shopping by overcoming a lack of social interactions between sellers and buyers which have been raised as a limitation in electronic commerce. Drawing on the studies of communication media, this study examines how live commerce contributes to the increase of virtual presence which consists of telepresence and social presence. Telepresence refers to a buyer's perception that he or she is present at the physical shopping mall during live shopping streaming whereas social presence refers to a buyer's perception of social interaction with a seller which is human warm, social, sensitive, and personal. In this study, we verify key determinants of virtual presence and its consequences. More specifically, this study proposes virtual presence contributes to the increase of buyers' trust in products and further purchase intentions. Furthermore, we verify influential factors of virtual presence from the technical and influencer perspectives of live commerce. Design/methodology/approach: To test the proposed hypotheses, the partial least squares (PLS) analysis is conducted with a total of 250 data collected on users with experience in the TaoBao live streaming shopping platform. Findings: The results show that first, telepresence and social presence are increased by visibility, media richness and attractiveness in the context of live shopping streaming. Second, buyers' trust in product trust and purchase intentions are positively influenced by telepresence and social presence. Finally, buyers' trust in product has a direct, positve effect on their purchase intentions. Overall, the findings offer new insights into the studies of electronic commerce by introducting the concepts of virtual presence and media richness from the literature of communication media in the field of live commerce.