• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.597-600
• /
• 2003

The development and maintenance of a sound bond are an essential requirements of concrete repair and replacement. The bond property of a bonded overlay to its substrate concrete during the lifetime is one of the most important performance requirements which should be quantified. A standard or a verified bond strength measurement method is required at field for screening, selecting materials and quality control for overlay or repair materials. This study compares the nipple pipe direct tensile test, flexural adhesion test, and core pull-off test with their test results. Substantial differences in the failure stresses of three test methods were attributed to their different geometries and loading conditions. From these comparison and investigation, core pull-off test was relatively good because the coefficient of variation values were about 2%. It would be suitable for use in-situ because of its simplicity and accuracy.

• KIEAE Journal
• /
• v.14 no.5
• /
• pp.67-73
• /
• 2014

This study aims at examining kinetic efficient shading systems and their implementation methods. These days, the importance of the shading devices are getting more significant due to the energy problem. Cordially, suitable shade designs are required as an important element for the exterior envelope of the building. This study employs the optimal shading design as an efficient shading method with the kinetic system that can be converted actively by the altitude of the sun. The proposed kinetic shading system works not only as a lightshelf in case the altitude of the sun is high but also as a vertical louver when the sun is getting lower in order to block the direct sunlight. This study has analyzed the thermal performance and shading coefficient of the kinetic shading system in comparison to existing fixed shading devices using the Ecotect. The results, in sum, conclude that the suggested kinetic shading system could decrease direct sunlights 26.2% more than the existing shading methods.

• Journal of computational fluids engineering
• /
• v.1 no.1
• /
• pp.142-149
• /
• 1996

이차원 노즐을 통하여 저밀도 환경으로 팽창하는 희박류의 분석에 있어서 불연속좌표법과 결합된 유한차분법(finite-difference method coupled with the discrete-ordinate method, FDDO)과 직접모사법(direct-simulation Monte-Carlo method, DSMC)이 비교되었다. FDDO를 이용한 분석에서는 충돌적분모델을 도입하여 간단해진 볼츠만식(Boltzmann equation)이 불연속좌표법을 이용하여 물리적 공간에서는 연속이나 분자속도 공간에서는 불연속좌표로 표시되는 편미분방정식군으로 변환되어 유한차분법에의하여 수치해석 되었다. 직접모사법에서는 분자모델로 가변강구모델(variable hard sphere model, VHS)이, 충돌샘플링모델로는 비시계수법(no time counter method, NTC)이 채택되었다. 전혀 다른 두 가지 방법에 의한 노즐 내부에서의 유체흐름 해석결과는 매우 잘 일치하였으며, 노즐 외부의 plume 영역에서는 FDDO에 의한 해석결과가 직접모사법에 의한 해석결과에 비하여 약간 느린 팽창을 보였다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.3
• /
• pp.370-378
• /
• 2021

Purpose. The purpose of this study was to evaluate the currently published literatures investigating the accuracy of computer-aided design and computer-aided manufacturing removable partial denture (CAD-CAM RPD) framework with different manufacturing techniques and methods. Materials and methods. A comprehensive search for literatures was conducted in PubMed database using specific keywords with the patient, intervention, comparison, and outcome (PICO) question, "Is there a difference in accuracy of RPD frameworks manufactured using digital workflow according to the manufacturing process and methods?" Results. A total of 7 articles were selected. Two studies compared intraoral scanning and laboratory scanning for RPD frameworks and had heterogenous results. In the studies using different manufacturing process, RPD frameworks had clinically acceptable accuracy in both subtractive and additive manufacturing. Polyetheretherketone (PEEK)-milled RPD frameworks showed higher fit accuracy than traditionally casted or 3D printed RPDs. Direct milling method showed a higher accuracy than indirect milling method. However, in rapid prototyping, indirect method showed higher accuracy than direct method. Conclusion. The RPD frameworks fabricated using CAD-CAM technology showed a clinically acceptable level of accuracy regardless of manufacturing process or techniques. Consistent results have not been reported regarding the digital impression methods, which were intra oral scanning or laboratory scanning, and further studies are needed.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.8 no.1
• /
• pp.88-95
• /
• 2005

Direct Georeferencing by combined multi-sensor based on the direct measurement of the projection centers and rotation angle of sensor through loading the GPS and INS in aircraft. The method of combined multi-sensor can offer us to acquire the exterior orientation parameters with only minimum GCPs, even the ground control process could be completely skipped. Consequently, It is possible extreme to reduce the time and expense for the mapping process. In this study, a CCD camera is simultaneously used in combined multi-sensor surveying, and acquired CCD image through Direct Georeferencing produce digital orthoimage. In this process, methods of combining sensor and digital orthoimage are examined and estimated. For the comparison of the positioning accuracy digital orthoimage through Direct Georeferencing, GCPs determined by GPS surveying are used. Two digital orthoimage are produced; one with a few GCP and the other without them. The accuracy of orthoimages produced through combined multi-sensor with GCPs meets that of 1:1,000 maps. Without GCPs, it meets that of 1:5,000 maps.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.9_10 s.146
• /
• pp.1241-1252
• /
• 2005

This study tried to compare and analyze the body measurements of female adults in China by various age groups. As for the study method, direct and anthropometric measurements were used on the 357 female subjects living in Yenbien and Harbin, China, consisting of 122 women in their 20's, 114 women in their 40's, and 121 women in their 60's. The results were as follows: 1. The comparison of major body measurements between Korean Chinese and Korean in land indicated that the former were shorter and plumper than the latter. Those groups in their 60's did not show any significant difference in height related measurements and revealed less differences in body measurements comparing to other age groups. 2 The comparison of Chinese anthropometric measurements among age groups of Korean Chinese indicated that, higher the age, shorter the height measurements, the leg length shorter, the upper-half body length longer, and the chest drooping due to the breast descent. 3. The comparison of indirect measurements among age groups of Koreans Chinese indicated that those in their 60's showed many items of big discrepancies in comparison with those in their 20's or 40's, with wide gap in discrepancies, thus resulting in large differences among individuals.

• Journal of Mechanical Science and Technology
• /
• v.19 no.spc1
• /
• pp.481-486
• /
• 2005

This paper introduces a numerical method for integration of the linear and nonlinear differential dynamic equation of motion. The variation of acceleration in two time steps is approximated as a combination of both trigonometric cosine and hyperbolic cosine functions with weighted coefficient. From which all necessary formulae are elaborated for the direct integration of the governing equation. A number of linear and nonlinear dynamic problems with various degrees of freedom are analysed using both the suggested method and Newmark method for the comparison. The numerical results show high advantages and effectiveness of the new method.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.11
• /
• pp.2704-2710
• /
• 1993

A simple and straightforward method is introduced for developing continuum beam-rod model of a box-beam typed aircraft wing with composite layered skin based on "energy equivalence." The equivalent continuum structral properties are obtained from the direct comparison of the reduced stiffness and mass matrices for box-beam typed wing with those for continuum beam-rod model. The stiffness and mass matrices are all represented in terms of the continuum degrees-of freedom defined in this paper. The finite-element method. The advantage of the present continuum method is to give every continuum structural properties including all possible coupling terms which represent the couplings between different deformations. To evaluate the continuum method developed in this paper, free vibration analyses for both continuum beam-rod and box-beam are conducted. Numerical tests show that the present continuum method gives very reliable structural and dynamic properties compared to the results by the conventional finite-element analysis. analysis.

• Transactions of Materials Processing
• /
• v.5 no.4
• /
• pp.343-352
• /
• 1996

One of the preferred methods that can be used to verify the results of finite element analysis is to measure surface strains of the deformed part for purpose of direct comparison with simulation results. Instead of using the usual manual method the vision-based measurement method is capable of determining surface geometry and strain from the deformed grid pattern automatically with the help of a computer. To obtain strain distribution over an area, the coordinates of such a surface grid are determined from the multiple video images by applying the photogrammetry principle. Methods to improve the overall accuracy of the vision-based strain measurement system are explored and the possible accuracies that can be attained by such a measurement method are discussed. A major emphasis is placed on the initial grid application method its accuracy and ease of subsequent image processing. Finite element analyses of limiting dome height(LDH) test are carried out and the results of them are compared with exsperimen-tal data.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.6
• /
• pp.851-858
• /
• 2018

Objective: This study was conducted to compare different methods on effective energy evaluation of corn silage for beef cattle. Methods: Twenty Wandong bulls (Chinese indigenous yellow cattle) with initial body weight of $281{\pm}15.6kg$, were assigned to 1 of 5 dietary treatments with 4 animals per treatment in a randomized complete block design. Five dietary treatments included group 1 with corn silage only diet, group 2 with corn silage-concentrate basal diet (BD) and 3 groups with 3 test diets, which were the BD partly substituted by corn silage at 10%, 30%, and 60%. The total collection digestion trial was conducted for 5 d for each block after a 10-d adaptation period, and then an open-circuit respiratory cage was used to measure the gas exchange of each animal in a consecutive 4-d period. Results: The direct method-derived metabolizable energy and net energy of corn silage were 8.86 and 5.15 MJ/kg dry matter (DM), expressed as net energy requirement for maintenance and gain were 5.28 and 2.90 MJ/kg DM, respectively; the corresponding regression method-derived estimates were 8.96, 5.34, 5.37, and 2.98 MJ/kg DM, respectively. The direct method-derived estimates were not different (p>0.05) from those obtained using the regression method. Using substitution method, the nutrient apparent digestibility and effective energy values of corn silage varied with the increased corn silage substitution ratio (p<0.05). In addition, the corn silage estimates at the substitution ratio of 30% were similar to those estimated by direct and regression methods. Conclusion: In determining the energy value of corn silage using substitution method, there was a discrepancy between different substitution ratios, and the substitution ratio of 30% was more appropriate than 10% or 60% in the current study. The regression method based on multiple point substitution was more appropriate than single point substitution on energy evaluation of feedstuffs for beef cattle.