• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11C
• /
• pp.1085-1097
• /
• 2009

We present a structure and design method of the D8PSK modem compatible with the VDL mode-2 standard and performance test results of the developed modem. In VDL mode-2, the raised cosine filter is used only in the transmitter and a general low pass filter is used in the receiver. Consequently, we can not achieve ISI reduction but can have better spectrum characteristics. Although there is 1~2 dB performance degradation with an un-matched filter compared to that with a matched filter, it is more important to minimize adjacent channel interference in narrow band communications. The transmit signal is generated digitally to avoid the problems(I/Q imbalance and DC offset etc.) of analog modulators. In addition the digital down converter using digital IF sampling technique is adopted for the receiver. This paper contains the overall configuration, design method and simulation results based in part on the previously proposed structures and algorithms. It is confirmed that the modem transmits and receives messages successfully at a speed of max. 870 km/h over ranges of up to 310 km through the ground and in-flight communication tests.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.825-833
• /
• 2016

This paper introduces a direct-conversion CMOS RF transmitter for the IEEE 802.15.4 standard with a low-power high-gain up-conversion mixer designed in $0.18{\mu}m$ process. The designed RF DCT(Direct Conversion Transmitter) is composed of differential DAC(Digital to Analog Converter), passive low-pass filter, quadrature active mixer and drive amplifier. The most important characteristic in designing RF DCT is to satisfy the 2.4 GHz Zigbee standard in low power. The quadrature active mixer inside the proposed RF DCT provides enough high gain as well as sufficient linearity using a gain boosting technique. The measurement results for the proposed transmitter show very low power consumption of 7.8 mA, output power more than 0 dBm and ACPR (Adjacent Channel Power Ratio) of -30 dBc.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.7
• /
• pp.636-645
• /
• 2015

In this paper, unusual harmonics noise problem of digital electronic products in mass production was introduced and a practical solution was proposed. Generally, 5th or higher harmonics noise level has been ignored in circuit designs because over 5th harmonics noise decreases by 40 (dB/decade). Through some measurements, it is confirmed that over 10th harmonics noise can propagate and radiate in case of a certain PCB or housing conditions. We propose a capacitively loaded micro-strip low pass filter for commercial products having spatial design constraints and measured the effectiveness. The proposed structure can solve both of the continual increment of harmonics noise level and the spatial design constraint of commercial products. We expect the proposed method be effectively used for various digital electronic products.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.2
• /
• pp.9-16
• /
• 2015

In this paper, selection criterions on selection diversity are researched. The diversity is applied to the multiple antenna system based on wireless access in vehicular environment (WAVE) standard for rapid varying channel. Least squares (LS) based decision feedback equalizer (DFE) are used for channel equalization. Received signal is regenerated by means of the decision feedback path. In the selection diversity, the regenerated signal as well as the received signal is selected according to selection criterion. The decision feedback algorithm can follow the fast speed of WAVE fading channel. To control the tracking speed of the time-varying channel, simple low pass filter is used. Finally, the estimated channel value recovers the distorted payloads. Signal power before automatic gain control (AGC) in analog stage can be used as a selection criterion. In the digital stage, signal power after AGC, noise power after AGC, signal to noise ratio after AGC and cross-correlation method can be used as selection criterions. According to the simulation results, the performance of the selection diversity is improved in comparison with that of the combining diversity for the WAVE fading channel.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.3
• /
• pp.487-492
• /
• 2016

In this paper, a device for analyzing the pressure distribution during walking was produced by using the pressure sensor on the heel. This device was limited to a frequency band by using the 1st low-pass filter. And an algorithm to analyze the value of the quantity to pressure using a analog to digital converter. It is used by using the threshold voltage of pressure sensor, it is suggested the algorithm. The algorithm is detected the peak which is exceeded the threshold voltage. and thus in accordance, it is detected the number of steps. And the calorie consumption were detected by using it. Also it used an MCU and Bluetooth. And by confirming the data at the LCD of the other MCU, it was to reduce the size of the device. According to this algorithm, it has the advantage that there is no restriction on the activity than when using an imaging device and it is inexpensive than other sensors such as an acceleration sensor or a gyro and it is easy to handle.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.8A
• /
• pp.1252-1258
• /
• 1999

This paper describes a COMS IF transceiver IC for 10-MHz bandwidth wireless local loops. It interfaces between the RF section and the digital MODEM section and performs the IF-to-baseband (Rx) and baseband-to-IF (Tx) frequency conversions. The chip incorporates variable gain amplifiers, phase-locked loops, low pass filters, analog-to-digital and digital-to-analog converters. It has been implemented in a 0.6 -${\mu}{\textrm}{m}$ 2-poly 3-metal CMOS process. The phase-locked loops include voltage-controlled oscillators, dividers, phase detectors, and charge pumps on chip. The only external complonents are the filter and the varactor-tuned LC tank circuit. The chip size is 4 mm $\times$ 4 mm and the total supply current is about 57 mA at 3.3 V.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.1
• /
• pp.136-141
• /
• 2007

The Purpose Of This Paper Is To Use A Tactile Sensor To Compensate The Error Rate. Most Automated Sphygmomanometers Use The Oscillometric Method And Characteristic Ratio To Estimate Systolic And Diastolic Blood Pressure. However, Based On The Fact That Maximum Amplitude Of The Oscillometric Waveform And Characteristic Ratio Are Affected By Compliance Of The Aorta And Large Arteries, A Method To Measure The Artery Stiffness By Using A Tactile Sensor Was Chosen In Order To Integrate It With The Sphygmomanometer In The Future Instead Of Using Photoplethysmography. Since Tactile Sensors Have Very Weak Movements, Efforts Were Made To Maintain The Subject's Arm In A Fixed Position, And A 40hz Low Pass Filter Was Used To Eliminate Noise From The Power Source As Well As High Frequency Noise. An Analyzing Program Was Made To Get Time Delay Between The First And Second Peak Of The Averaged Digital Volume Pulse(${\Delta}t_{dvp}$), And The Subject's Height Was Divided By ${\Delta}t_{dvp}$ To Calculate The Stiffness Index Of The Arteries($Si_{dvp}$). Regression Equations Of Systolic And Diastolic Pressure Using $Si_{dvp}$ And Mean Arterial Pressure(Map) Were Computed From The Test Group (60 Subjects) Among A Total Of 121 Subjects(Age: $44.9{\pm}16.5$, Male: Female=40:81) And Were Tested In 61 Subjects To Compensate The Error Rate. Error Rates Considering All Subjects Were Systolic $4.62{\pm}9.39mmhg$, And Diastolic $14.40{\pm}9.62mmhg$, And Those In The Test Set Were $3.48{\pm}9.32mmhg,\;And\;14.34{\pm}9.67mmhg$ Each. Consequently, Error Rates Were Compensated Especially In Diastolic Pressure Using $Si_{dvp}$, Various Slopes From Digital Volume Pulse And Map To Systolic-$1.91{\pm}7.57mmhg$ And Diastolic $0.05{\pm}7.49mmhg$.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.468-475
• /
• 2018

In medical ultrasound imaging, frequency-dependent attenuation downshifts and reduces a center frequency and a frequency bandwidth of received echo signals, respectively. This causes considerable errors in quadrature demodulation (QDM), result in lowering signal-to-noise ratio (SNR) and contrast resolution (CR). To address this problem, adaptive dynamic QDM (ADQDM) that estimates center frequencies along depth was introduced. However, the ADQDM often fails when imaging regions contain hypoechoic regions. In this paper, we introduce a valid region-based ADQDM (VR-ADQDM) method to reject the misestimated center frequencies to further improve SNR and CR. The valid regions are regions where the center frequency decreases monotonically along depth. In addition, as a low-pass filter of QDM, Gaussian wavelet based dynamic filtering was adopted. From the phantom experiments, average SNR improvements of the ADQDM and the VR-ADQDM over the traditional QDM were 1.22 and 5.27 dB, respectively, and the corresponding maximum SNR improvements were 2.56 and 10.58 dB. The contrast resolution of the VR-ADQDM was also improved by 0.68 compared to that of the ADQDM. Similar results were obtained from in vivo experiments. These results indicate that the proposed method would offer promises for imaging technically-difficult patients due to its capability in improving SNR and CR.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.97-104
• /
• 2004

As a device that returns surplus energy, regenerated from trains to d.c. source, to a.c. system and reuses it, the thyristor Inverter has been widely used. Because the conventional thyristor inverter is a unidirectional phase-controlled device, it Is Impossible to control the power factor of its output. Moreover, harmonics emission is high and it needs to take a additional filter. In this paper, to solve the problems stated above, the inverter, which can control real and reactive power by adopting IGBT modules as switching elements and being controlled by means of space vector PWM, is developed. Considering high economical efficiency and reliability in order to apply to the system for commercial use, the developed inverter is equipped with fully digital control system and low pass filter, and reduces harmonics and has compact size. The detail description about the developed inverter is stated in various respects: design criteria, technical description, power circuits, control techniques, the developed system, test results, etc.

• The Journal of Korean Institute of Information Technology
• /
• v.17 no.8
• /
• pp.11-19
• /
• 2019

Against advanced image-related crimes, a high level of digital forensic methods is required. However, feature-based methods are difficult to respond to new device features by utilizing human-designed features, and deep learning-based methods should improve accuracy. This paper proposes a deep learning model to identify camera models based on DenseNet, the recent technology in the deep learning model field. To extract camera sensor features, a HPF feature extraction filter was applied. For camera model identification, we modified the number of hierarchical iterations and eliminated the Bottleneck layer and compression processing used to reduce computation. The proposed model was analyzed using the Dresden database and achieved an accuracy of 99.65% for 14 camera models. We achieved higher accuracy than previous studies and overcome their disadvantages with low accuracy for the same manufacturer.