• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.6
• /
• pp.736-744
• /
• 2005

Statement of problem. Initial stability of implant is an important factor for predicting osseointegration. It requires a rapid, non-invasive, user-friendly technique to frequently assess the implant stability and the degree of osseointegration. Purpose. The aim of this study was to evaluate the correlation between the resonance frequency analysis (RFA) and the radiographic method for peri-implant bone change under in vitro conditions. Material and Method. Twenty implants of 3.75 mm in diameter(Neoplant, Neobiotech, Korea) were used. To simulate peri-implant bone change, 2 mm-deep $45^{\circ}$ range horizontal defect and 2 mm-deep $90^{\circ}$ range horizontal defect area were serially prepared perpendicular to the X-ray beam after conventional implant insertion. Customized film holding device was fabricated to standardize the projection geometry for serial radiographs of implants and direct digital image was obtained. ISQ values and gray values inside threads were measured before and after peri-implant bone defect preparation. Results. Within a limitation of this study, ISQ value of resonance frequency analysis was changed according to peri-implant bone change (p<0.05) and gray value of radiographic method was changed according to peri-implant bone change (p<0.05). There was no correlation between the ISQ value and the gray value for peri-implant bone change (p>0.05). But, in horizontal defect condition, relatively positive correlation were between ISQ and gray values(r=0.663). Conclusion. This results provided a possibility that peri-implant bone change may be evaluated by both RFA and radiographic method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.297-307
• /
• 2010

Recently, maintenance engineering and technology for civil and building structures have begun to draw big attention and actually the number of structures that need to be evaluate on structural safety due to deterioration and performance degradation of structures are rapidly increasing. When stiffness is decreased because of deterioration of structures and member cracks, dynamic characteristics of structures would be changed. And it is important that the damaged areas and extent of the damage are correctly evaluated by analyzing dynamic characteristics from the actual behavior of a structure. In general, typical measurement instruments used for structure monitoring are dynamic instruments. Existing dynamic instruments are not easy to obtain reliable data when the cable connecting measurement sensors and device is long, and have uneconomical for 1 to 1 connection process between each sensor and instrument. Therefore, a method without attaching sensors to measure vibration at a long range is required. The representative applicable non-contact methods to measure the vibration of structures are laser doppler effect, a method using GPS, and image processing technique. The method using laser doppler effect shows relatively high accuracy but uneconomical while the method using GPS requires expensive equipment, and has its signal's own error and limited speed of sampling rate. But the method using image signal is simple and economical, and is proper to get vibration of inaccessible structures and dynamic characteristics. Image signals of camera instead of sensors had been recently used by many researchers. But the existing method, which records a point of a target attached on a structure and then measures vibration using image processing technique, could have relatively the limited objects of measurement. Therefore, this study conducted shaking table test and field load test to verify the validity of the method that can measure multi-point displacement responses of structures using image processing technique.

• Cartoon and Animation Studies
• /
• s.45
• /
• pp.215-233
• /
• 2016

Timelapse which was appeared Georges Mellieoseu in 1897 was not familiar to people and was not popular in film or broadcast industry in spite of long history. But about 5 years ago, timelapse has become distinguished in all around image art, because it show us aesthetic extraction of time and variation of color in Vimeo and Youtube which neve been seen before. So nowadays latest camera has come out with default menu which can shoot timelapse. But popularity of timelapse seem not development of cinematography technique or appearance of new function but production of image which reflects ages of present with fully accept digital media property. This study is approached from two formative characteristics. First it is strengthen of time which is showed timelapse and analog media from a comparison angle. Second, it is how to extend their sense and imitate images through resolution which can be possible high quality image and color especially with Raw data Through these methodology, this study defines correlation of character of digital media and artistic value of images in timelapse. And also it cleary assures the era of penetrating art has not only visual amusement as known but, also representative value of our ages and technology of media.

• Smart Structures and Systems
• /
• v.25 no.2
• /
• pp.135-153
• /
• 2020

There has been a sustained interest towards the non-contact structural displacement measurement by means of videogrammetric technique. On the way forward, one of the major concerns is the spurious image drift induced by temperature variation. This study therefore carries out an investigation into the temperature effect of videogrammetric technique, focusing on the exploration of the mechanism behind the temperature effect and the elimination of the temperature-caused measurement error. 2D videogrammetric measurement tests under monotonic or cyclic temperature variation are first performed. Features of measurement error and the casual relationship between temperature variation and measurement error are then studied. The variation of the temperature of digital camera is identified as the main cause of measurement error. An excellent linear relationship between them is revealed. After that, camera parameters are extracted from the mapping between world coordinates and pixels coordinates of the calibration targets. The coordinates of principle point and focal lengths show variations well correlated with temperature variation. The measurement error is thought to be an outcome mainly attributed to the variation of the coordinates of principle point. An approach for eliminating temperature-caused measurement error is finally proposed. Correlation models between camera parameters and temperature are formulated. Thereby, camera parameters under different temperature conditions can be predicted and the camera projective matrix can be updated accordingly. By reconstructing the world coordinates with the updated camera projective matrix, the temperature-caused measurement error is eliminated. A satisfactory performance has been achieved by the proposed approach in eliminating the temperature-caused measurement error.

• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1213-1221
• /
• 2020

Chromium-nickel alloy 42XNM (XHM-1, Bochvalloy) is considered as a promising material for future generations of nuclear reactors, primarily as a material for the fuel elements shells in the development of accident tolerant fuel. However, as with most nickel-based alloys, 42ХNМ is characterized by a sharp decrease in plastic properties in the temperature range of (500-900)℃. This effect is enhanced by neutron irradiation. Preliminary tests of ring samples of 42XNM alloy (after irradiation as a part of the VVER-1000 control system) in the temperature range of ductility failure showed that the standard technique for processing tensile diagrams does not allow to evaluate the plastic properties correctly at low strains. Therefore, in this work, the alternative method for testing ring samples from materials with low plastic characteristics was developed. It was shown that the minimum value of the permanent strain of the irradiated 42XNM alloy in the temperature range of (500-1100)℃, determined by the alternative method, was ~1.6% at 750 ℃.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.26-36
• /
• 2006

In this paper, we propose a cost-effective color filter may (CFA) demosaicing method for digital still cameras in which a single CCD or CMOS image sensor is used. Since a CFA is adopted, we must interpolate missing color values in the red, green and blue channels at each pixel location. While most state-of-the-art algorithms invest a great deal of computational effort in the enhancement of the reconstructed image to overcome the color artifacts, we focus on eliminating the color artifacts with low computational complexity. Using spatial correlation of the adjacent pixels, the edge-directional information of the neighbor pixels is used for determining the edge direction of the current pixel. We apply our method to the state-of-the-art algorithms which use edge-directed methods to interpolate the missing color channels. The experiment results show that the proposed method enhances the demosaiced image qualify from $0.09{\sim}0.47dB$ in PSNR depending on the basis algorithm by removing most of the color artifacts. The proposed method was implemented and verified successfully using verilog HDL and FPGA. It was synthesized to gate-level circuits using 0.25um CMOS standard cell library. The total logic gate count is 12K, and five line memories are used.

• Tunnel and Underground Space
• /
• v.34 no.2
• /
• pp.169-184
• /
• 2024

This study investigates acoustic emission (AE) and micro-deformation characteristics of circular openings through biaxial compression experiments. The experimental results showed a significant increase in the frequency, count, energy, and amplitude of AE signals immediately before damage occurred in the circular opening. The differences in frequency and count between before and after damage initiation were significantly pronounced, indicating suitable factors for identifying damage occurrence in circular openings. The results for digital image correlation (DIC) technique revealed that micro-deformation was concentrated around the openings, as evidenced by the spatial distribution of strain. In addition, spalling was observed at the end of the experiments. The AE and micro-deformation characteristics presented in this study are expected to serve as fundamental data for evaluating the stability of underground openings and boreholes for deep subsurface projects.

• Journal of KIISE:Software and Applications
• /
• v.31 no.9
• /
• pp.1142-1149
• /
• 2004

Motion Estimation(ME) has been developed to reduce temporal redundancy in digital video signals and increase data compression ratio. ME is an Important part of video encoding systems, since it can significantly affect the output quality of encoded sequences. However, ME requires high computational complexity, it is difficult to apply to real time video transmission. for this reason, motion estimation algorithms with low computational complexity are viable solutions. In this paper, we present an efficient method with low computational complexity based on spatial and temporal correlations of motion vectors. The proposed method uses temporally and spatially correlated motion information, the motion vector of the block with the same coordinate in the reference frame and the motion vectors of neighboring blocks around the current block in the current frame, to decide the search pattern and the location of search starting point adaptively. Experiments show that the image quality improvement of the proposed method over MVFAST (Motion Vector Field Adaptive Search Technique) and PMVFAST (Predictive Motion Vector Field Adaptive Search Technique) is 0.01～0.3(dB) better and the speedup improvement is about 1.12～l.33 times faster which resulted from lower computational complexity.

• The Journal of the Korea Contents Association
• /
• v.5 no.3
• /
• pp.123-131
• /
• 2005

Among the digital halftoning, the error diffusion halftoning gives better subjective quality than other halftoning techniques. But it also makes edges of objects blurred. To overcome the defect, this paper proposes the modified error diffusion halftoning algorithm to enhance the edges using the spatial perceptual properties of the human visual system. Using the properties that the human eyes perceive not the pixel's luminance itself but the local average luminance and the information that human eyes perceive spatial variation, the proposed method computes information of edge enhancement(IEE). The IEE is added to the quantizer's input pixel and feeds into the halftoning quantizer. The quantizer produces the halftone image having the enhanced edge. Also this paper proposes the technique that the coefficients of the error diffusion filter are adapted according to the correlation among color components. The computer simulation results show that the proposed method produces finer halftoning images than conventional methods due to the enhanced edges. And the proposed method also preserves similar in edges to original image and reduces some defects such as color impulse and false contours.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.4 s.310
• /
• pp.66-73
• /
• 2006

Safety is the most important for all traffic management and control technology. This paper focuses on developing a flexible, reliable and real-time processing algorithm which is able to generate signal for the entering vehicle at the joining road through a camera and image processing technique. The images obtained from the camera located beside and upon the road can be used for traffic surveillance, the vehicle's travel speed measurement, predicted arriving time in joining area between main road and joining road. And the proposed algorithm displays the confluence safety signal with red, blue and yellow color sign. The three methods are used to detect the vehicle which is driving in setted detecting area. The first method is the gray scale normalized correlation algorithm, and the second is the edge magnitude ratio changing algorithm, and the third is the average intensity changing algorithm The real-time prototype confluence safety signal generation algorithm is implemented on stored digital image sequences of real traffic state and a program with good experimental results.