• Interaction and multiscale mechanics
• /
• v.1 no.2
• /
• pp.177-190
• /
• 2008

In this paper, both experimental measurement and theoretical analysis are used to investigate the out-of-plane resonant characteristics of a cantilevered piezoceramic plate in air and three different kinds of fluid. The experimental method, amplitude-fluctuation electronic speckle pattern interferometry (AF-ESPI), is the major technique used in this study to measure the resonant characteristics of the cantilivered piezoceramic plate. Both resonant frequencies and full-field mode shapes are obtained from this experimental technique. Numerical computations based on the finite element analysis are presented for comparison with the experimental results. Good quality of mode shapes for the cantilevered piezoceramic plate in air is obtained from the AF-ESPI technique. However, the quality decreases as the viscosity of fluids increases. From the results provided from experimental measurements and numerical computations, it is indicated that the resonant frequencies of the cantilevered piezoceramic plate in fluid decrease with the increase of the viscosity of fluids. Good agreements between the experimental measured data and the numerical calculated results are found for both resonant frequencies and mode shapes of the cantilevered piezoceramic plate in fluid.

• Structural Monitoring and Maintenance
• /
• v.5 no.3
• /
• pp.379-390
• /
• 2018

In this paper, a novel and effective damage diagnosis algorithm is proposed to detect and estimate damage using two stages least squares support vector machine (LS-SVM) and limited number of attached sensors on structures. In the first stage, LS-SVM1 is used to predict the unmeasured mode shapes data based on limited measured modal data and in the second stage, LS-SVM2 is used to predicting the damage location and severity using the complete modal data from the first-stage LS-SVM1. The presented methods are applied to a three story irregular frame and cantilever plate. To investigate the noise effects and modeling errors, two uncertainty levels have been considered. Moreover, the performance of the proposed methods has been verified through using experimental modal data of a mass-stiffness system. The obtained damage identification results show the suitable performance of the proposed damage identification method for structures in spite of different uncertainty levels.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.171-180
• /
• 2001

Collision accident reconstruction algorithm are developed based on the deformation shape and severity of a car body. At first, the body stiffness equation representing the force-deformation relationship is derived using finite element analysis for head on collision of two cars. The database of deformation shapes and energies is constructed for five different collision configurations; each configuration contains three velocity conditions. Deformation shapes are obtained using a curve fitting method and result in cubic polynomials. Deformation energies are calculated using a stiffness equation and deformation data. Three algorithms are developed to reconstruct collision configuration compared with constructed database. The developed algorithms show reasonably good performance to find collisions conditions for some test problems.

• Journal of ILASS-Korea
• /
• v.1 no.4
• /
• pp.40-45
• /
• 1996

This Paper addresses to spray characteristics in w-shaped diesel engine combustion chamber which has impingement parts for 4 sprays injected from an injector. The two-dimensional shapes have been chosen to avoid the difficulties for analysing the spray dynamics in the real chamber. The simple shapes are reproduced with same geometries in vertical or horizontal sections through the impingement lands. The spray developments are visualized with a high speed drum camera and shadowgraphy optical system, and the droplet sizes are measured by Malvern system. The detailed discussions m made for the two different combustion chamber shapes, which are new w-shape using spray wall impaction and general w-shape. The results show that the spray characteristics of the new shape are superior to those of the general w-shape.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2168-2173
• /
• 2003

Pressure balancing valve is one of important control devices, which is fully automatic and no manual controls, regulating or adjustments are needed. It is typically used to maintain constant temperature of working fluid in power and chemical plants and domestic water supply systems. Pressure balancing valve is composed of body, cylinder and balancing piston. Therefore, the balancing piston shapes are important design parameters for a pressure balancing valve. In this study, numerical and experimental analyses are carried out with two different balancing piston shapes. Especially, the distribution of static pressure is investigated to calculate the flow coefficient($C_v$). The governing equations are derived from making using of three-dimensional Navier-Stokes equations with standard ${\kappa}-{\varepsilon}$ turbulence model and SIMPLE algorithm. Using commercial code, PHOEIC, the pressure and flow fields in pressure balancing valve are depicted.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.5
• /
• pp.496-502
• /
• 2008

In this study, supersonic and hypersonic flutter characteristics have been analyzed for the various typical section shapes of missile fin configurations. Nonlinear flutter analyses are conducted considering the effect of moving shock waves. Computational fluid dynamic method is applied to accurately predict unsteady aerodynamic loads due to structural motions for the solution of aeroelastic governing equations. Commonly used typical section shapes of supersonic and hypersonic launch vehicles are considered in the present numerical study. Detailed flutter responses for four different typical section models are presented and the flutter characteristics are physically investigated.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.3
• /
• pp.259-267
• /
• 1997

Average heat transfer coefficients and friction coefficients have been measured from staggered short pin-fin arrays to investigate the effect of fin shapes. Flow entering into the test section is a fully developed duct flow and the Reynolds number ranges from 5,000 to 25,000 based on fin diameter and average approaching velocity. The fin has three different shapes; uniform-diameter circular fin, two stepped-diameter circular fins. Average heat transfer rates change slightly with the fin shapes. However, friction loss(pressure loss) for the stepped-diameter fins is significantly less than that for the uniform-diameter fin. This results indicate that the stepped-diameter fin arrays in duct flow enhance heat transfer rates largely based on unit pumping power.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1495-1496
• /
• 2008

The Ceramic Metal Halide lamp is different from optical characteristic on shapes of arc-tube and driving method of ballast. In this paper, we measured optical characteristics of the Ceramic Metal Halide lamp that uses arc tubes which are spherical and cylindrical shapes, and analyzed the Ceramic Metal Halide lamp connecting ballast that is electronic and magnetic types through the lamp measurement system that is given for stabilization period of fifteen minutes. In result, the arc-tube of spherical shape is more improvement in the optical properties than the arc tube of cylindrical shape, moreover, the electronic ballast is more efficient than the optical properties of the magnetic ballast.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.136-142
• /
• 2014

A major problem in Switched Reluctance Motor (SRM) is torque ripple, which causes undesirable acoustic noise and vibration. This work focuses on reducing the undesirable torque ripple in SRM by modifying stator and rotor geometry. This paper presents a comparative study on torque ripple minimization in SRM with modified pole shapes such as stator pole taper, stator pole face with non-uniform air gap and pole shoe attached to rotor pole. Further this paper presents a detailed sensitivity analysis of the effect of different geometrical parameters that alter the pole face shapes on the performance of SRM. The analysis is performed using finite-element method considering average torque and torque ripple as performance parameters. Based on the analysis, a design combining stator pole taper with non-uniform air gap is proposed to improve the torque characteristics of SRM. The dynamic characteristics of the proposed design are simulated and the results show satisfactory reduction in torque ripple.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.5
• /
• pp.354-365
• /
• 2007

We present novel methods to generate a sequence of shapes that represents the pattern of morphological development or transformation of Bezier curves. The presented methods utilize the intrinsic geometric structures of a Bezier curve that are derived from rib and fan decomposition (RFD). Morphological development based on RFD shows a characteristic pattern of structural growth of a Bezier curve, which is the direct consequence of development path defined by fans. Morphological transformation based RFD utilizes development patterns of source and target curves to mimic the theory of evolutionary developmental biology: although the source and target curves are quite different in shapes, we can easily find similarities in their younger shapes, which makes it easier to set up feature correspondences for blending them. We also show that further controls on base transformation for intensity of feature blending, and extrapolation can compensate the immaturity of blended curves. We demonstrate the experimental results where transformation patterns are smoother and have unique geometric style that cannot be generated using conventional methods based on multi-linear blending.