• Smart Structures and Systems
• /
• v.15 no.3
• /
• pp.523-541
• /
• 2015

Structural health monitoring of steel truss bridge based on changes in modal properties was investigated in this study. Vibration measurements with five sensors were conducted at an existing Warren truss bridge with partial fractures in diagonal members before and after an emergency repair work. Modal properties identified by the Eigensystem Realization Algorithm showed evidences of increases in modal damping due to the damage in diagonal member. In order to understand the dynamic behavior of the bridge and possible mechanism of those increases in modal damping, theoretical modal analysis was conducted with three dimensional frame models. It was found that vibrations of the main truss could be coupled internally with local vibrations of diagonal members and the degree of coupling could change with structural changes in diagonal members. Additional vibration measurements with fifteen sensors were then conducted so as to understand the consistency of those theoretical findings with the actual dynamic behavior. Modal properties experimentally identified showed that the damping change caused by the damage in diagonal member described above could have occurred in a diagonal-coupled mode. The results in this study imply that damages in diagonal members could be detected from changes in modal damping of diagonal-coupled modes.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.5
• /
• pp.161-168
• /
• 2010

Practicing engineers and researchers need computational tools that estimate accurately the cyclic response of RC walls, and in particular, force and deformation capacities and their materials strains. So this paper describes a nonlinear truss modeling approach for reinforced concrete walls, or in general, for plane stress reinforced concrete elements subjected to cyclic reversals. Nonlinear vertical, horizontal, and diagonal truss elements are used to represent concrete and steel reinforcement. The wall having aspect ratio of 1.2 was chosen to be compared with the experimental results. Here, four types of main diagonal member models and three types of diagonal members models were applied to find out more accurate results of analysis.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.4
• /
• pp.139-146
• /
• 2002

A analysis of crack behavior in RC member was performed by nonlinear finite element method. Two crack models were used in F.E.M.(finite element method): one was FCM (the fixed crack model) and the other was RCM (the rotated crack model). Based on parametric study, the ratio of shear steel, strength of concrete, and a/d(shear span/effective depth) were compared with test results of references. According to the test results, when the member behavior was affected by the shear or diagonal tension, RCM was reasonable. However, when the behavior was affected by the flexibility, FCM was more appropriate. In addition, each crack model behavior for the change of shear steel ratio, the increase of strain energy was constant in FCM, but it was different in RCM because of diagonal crack distribution and crack width. Since the strength of concrete is affected not only by shear but also by flexural strength, each crack model behavior yields similar results.

• Journal of Information Display
• /
• v.8 no.4
• /
• pp.23-26
• /
• 2007

A natural 3D image is considered by many people to be next-step in evolution of displays. This paper introduces autostereoscopic 3D of 60-view number, which is made using slanted lenticular lens array and LCD of 15.1 inch diagonal size and 3200 by 2400 pixel numbers and presents the results of our prototype. Due to its large view number, smooth motion parallax is observed and the visual fatigue is reduced.

• Journal of architectural history
• /
• v.26 no.3
• /
• pp.19-30
• /
• 2017

This paper studies the style emergence of Liujin Dougong in the ancient Chinese architecture. Dougong is the bracket set of the ancient Chinese wood structural architecture, and Liujin Dougong is one of the late styles of Chinese Dougong. It emerged in the period of the Ming Dynasty and has been installed in imperial palaces and imperial temples till the late period of the Qing Dynasty. Through the long term field survey and documental investigation, this research found out the some prototypes of Liujin Dougong among the earlier Xia-ang style Dougongs in the Song and Yuan Dynasty architectures. The symptom of style change appeared in the bracket composition. In the beginning, because Shuatou, the horizontal member just on Xia-ang was needed to be fixed to the inner main structure system, it was changed to the diagonal member and replaced Xia-ang. It brought continuous changes, the other horizontal members of Dougong also began to change to the diagonal form. And in accordance with these compositional changes of Dougong members, the decoration of inner parts also began to change. This paper analyzed every step of the compositional and decorative changes from Xia-ang Dougong style to Liujin Dougong style. In the addition, it also proposed the typical model of Qing style Liujin Dougong of which tail end is not placed on the beam and is just placed under the purlin, based on the its own research and analysis.

• Journal of the Korean Society of Safety
• /
• v.34 no.1
• /
• pp.53-61
• /
• 2019

This study performs reliability analysis of three-dimensional temporary shoring structures with three different models. The first model represents a field model which does not have diagonal bracing members. The installation of bracing members is often neglected in the field for convenience. The second model corresponds to a design model which has the bracing members with the hinge connection of horizontal and bracing members at joints. The third model is similar to the second model but the hinge connection is replaced with partial rotational stiffness. The reliability analysis results revealed that the vertical members of the three models are safe enough in terms of axial force, but the vertical and horizontal members exhibit a big difference among the three models in terms of combination stress of axial force and bi-axial bending moments. The field model showed significant increase in failure probability for the horizontal member, and thus the results demonstrate that the bracing member should be installed necessarily for the safety of the temporary shoring structures.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.10a
• /
• pp.187-192
• /
• 1995

Four types of experiments were performed to check the similitude of member behavior between prototype and 1/10 scale models:(1) Test of slender columns with P- effect, (2)Test of short columns with and without confinement steel, (3)Test of simple beams without stirrups, and (4)T-beam test. Based on the results of experiments, the conclusions were made as follows : (1) The P- effect of slender columns can be almost exactly represented by 1/10 acale model. (2)The effect of confinement on short columns by the hoop steel can also roughly simulated by 1/10 scale model. (3)The failure modes of simple beams models were the yielding of tension steel followed by large diagonal tension cracking+compressive concrete failure. (4)The behaviors of prototype and 1/10 scale model in T-beams appear very similar.

• Journal of the Korea Concrete Institute
• /
• v.11 no.5
• /
• pp.79-88
• /
• 1999

The purpose of this paper is to develop a mathematical expression for computing crack angles based on reinforcement volumes in the longitudinal and transverse directions, member end-fixity and length-to-width aspect ratio. For this a reinforced concrete beam-column element is assumed to possess a series of potential crack planes represented by a number of differential truss elements. Depending on the boundary condition, a constant angle truss or a variable angle truss is employed to model the cracked structural concrete member. The truss models are then analyzed using the virtual work method of analysis to relate forces and deformations. Rigorous and simplified solution schemes are presented. An equation to estimate the theoretical crack angle is derived by considering the energy minimization on the virtual work done over both the shear and flexural components the energy minimization on the virtual work done over both the shear and flexural components of truss models. The crack angle in this study is defined as the steepest one among fan-shaped angles measured from the longitudinal axis of the member to the diagonal crack. The theoretical crack angle predictions are validated against experimentally observed crack angle reported by previous researchers in the literature. Good agreement between theory and experiment is obtained.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.2
• /
• pp.313-321
• /
• 2008

Recently in Japan, fracturing was observed on the diagonal member of a through truss bridge at the boundary region with the concrete slab. Local corrosion damage where the diagonal member was enclosed in the concrete slab is an important factor in the fracture. In this study, accelerated exposure tests were carried out on concrete-steel model specimens simulating steel members at the boundary with concrete. Fatigue tests were then performed on the corroded model specimens. Accelerated exposure tests of the S6-cycle, which is carried out on the model specimens for 150, 300, 450 and 600 da ys. Their surface geometry was then measured. From the accelerated exposure test results, change in maximum and mean corrosion depths was determined according to the testing periods. The effect of local corrosion on fatigue strength was also presented based on the fatigue test results.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.5 s.72
• /
• pp.529-541
• /
• 2004

Concrete filled steel tube structures were recently used in constructing high-rise buildings due to their effectiveness. Studies on concrete filled steel tubes have been focused on the experiments of uni-axial compression and bending and eccentric compression. There were also a few studies that investigated CFT member behavior under combined compression and torsion. The behavior of a circular CFT column under combined torsion and compression was theoretically investigated, considering the confinement of steel tubes on the concrete, the softening of the concrete, and the spiral effect, which were the dominant factors that influenced compression and torsion strength. The biaxial stress effects due to diagonal cracking were also taken into account. By applying those factors to compatibility and equilibrium conditions, the basic equation was derived, and the equation could be used to incorporate the torsional behavior of the entire loading history of the CFT member.