• 한국재료학회지
• /
• 제27권3호
• /
• pp.172-178
• /
• 2017

The aim of this study is to consider the effect hydrogen on dezincification behavior of Cu-Zn alloys. The investigations include microstructural observations with scanning electron microscope and chemical composition analysis with energy dispersive spectrometer. The dezincification layer was found to occur in high pressure hydrogen atmosphere, not in air atmosphere. In addition, the layers penetrated into the inner side along the grain boundaries in the case of hydrogen condition. The shape of the dezincification layers was porous because of Zn dissolution from the ${\alpha}$ or ${\beta}$ phase. In the case of stress corrosion cracks formed in the Cu-Zn microstructure, the dezincification phenomenon with porous voids was also accompanied by grain boundary cracking.

• 수산해양기술연구
• /
• 제39권4호
• /
• pp.291-297
• /
• 2003

Al-brass is usually used as the tube material of vessel's heat exchanger for seawater cooling system because it has high thermal conductivity and good mechanical properties and high corrosion resistance due to cuprous oxide (Cu20) layer against seawater. However, Al-brass tubes of heat exchanger for vessel at the actual environment is reported that local corrosion such as stress corrosion cracking occurred by synergism effect between mechanical factor and corrosion environment In this paper, the effect of corrosion environment on the stress corrosion cracking of Al-brass in various NH4OH of 3.5% NaCl solution, under flow by constant displacement tester. Based on the test results, the behavior of polarization, stress corrosion crack propagation and dezincification phenomenon of Al-brass are investigated. The main results are as follows：(1) Increasing range of potential from open circuit potential to repassivation gets lower, as the contain rate of NH4OH gets higher. (2) As contain rate of NH4OH gets higher, SCC of Al-brass is become activation but the protection film(Cu20) of Al-brass is created in 3.5% NaCl solution. (3) According as content of NH4OH increases in 3.5% NaCl solution, the dezincifiction area is spread. It is concluded that dezincification occurred by localized preferential anodic dissolution at stress focusing region.

• Corrosion Science and Technology
• /
• 제2권3호
• /
• pp.135-140
• /
• 2003

The effect of temperature on stress corrosion cracking o f Al-brass used in vessel heat exchanger tube was studied in 3.5% NaCI + 0.1% $NH_4OH$ solution. The SCC test using a CDT(constant displacement test) and the specimens using a SEN(single edge notched) specimens. For setting the environment similar to working environment of a heat exchanger, the specimens was immersed in solution and solution flow onto the specimens were performed. The results are as follows : The latent time of stress corrosion crack occurrence gets shorter, as the temperature gets higher. Dezincification phase showed around the crack occupy wider range, as the temperature gets higher. Zn composition falls under 4% at the dezincifiction area.

• 한국해양공학회지
• /
• 제18권1호
• /
• pp.69-74
• /
• 2004

In general, the protection method of Shell and Tube Type heat exchanger for a vessel has been applied as a sacrificial anode, which is attached at the inner side of the shell. However, this is an insufficient protection method for tube. Therefore, a more suitable method, such as the impressed current cathodic protection for tube protection, is required. Al-brass is the raw material of tubes for heat exchanger of a vessel where seawater is used for cooling the water. It has a high level of heat conductivity, excellent mechanical properties, and a high level of corrosion resistance, due to a cuprous oxide (Cu$_2$O) layer against th seawater. However, in actuality, it has been reported that Al-brass tubes for heat exchanger of a vessel can produce local corrosion, such as stress corrosion cracking (SCC). This paper studied the effect of impressed potential on the stress corrosion cracking of Al-brass for impressed current cathodic protection in 3.5% NaCl +0.1% NH$_4$OH solution, under flow by a constant displacement tester. Based on the test results, the latent time of SCC, stress corrosion crack propagation, and the dezincification phase of Al-brass are investigated.

• 한국가스학회지
• /
• 제7권2호
• /
• pp.22-32
• /
• 2003

Al-황동은 기계적 특성 및 열전도성이 우수하고 해수 중에서 표면 보호피막을 형성하므로 부식저항성이 높아 해수를 냉각수로 사용하는 선박용 열교환기의 세관재로 널리 사용되고 있다 Al-황동 세관은 실제 사용 환경에서 굽힘 등에 의한 소성변형된 상태로 사용되는 경우가 많다. 이와 같은 소성변형에 의한 Al-황동 세관의 균열 파손사례는 선박의 오일탱크 내의 가열코일, 각종 열교환기의 세관 등에서 흔히 찾아 볼 수 있다. 또한 세관의 확관에 의한 밀봉 방법에 따라 세관의 변형에 의한 잔류응력 및 어패류 혼입에 의한 해수 유입부의 국부적인 유속증가 등에 기인하여 Al-황동 세관의 균열 및 침식 등의 파손사례가 보고되고있다. 본 연구에서는 $3.5\%$ NaCl. + $0.1\%\;NH_4OH$ 수용액을 시험편 표면에 5 m/s로 액분사하의 가속실험에서 Al-황동 세관의 응력부식균열 거동에 미치는 응력의 영향에 대하여 고찰하였다.

• 보존과학회지
• /
• 제33권3호
• /
• pp.167-179
• /
• 2017

서산 비경도 출수 상평통보를 대상으로 혐기성 수중 매장환경에서 형성되는 부식화합물 성분과 이에 따른 혐기성 부식 원인을 추정하였다. 미세조직 관찰, 원소 mapping, 층위별 주성분 분석, 부식화합물 동정을 실시하였다. 그 결과 표면의 고착물은 침상형 육면체형 팔면체형으로 분류되며, 그에 따른 분석 결과 Cu, Pb, S 등의 원소가 검출되었다. 원소 mapping에서는 최외곽에 Cu-S로 이루어진 뚜렷한 층이 확인되었다. 층위별 주성분은 Cu, S, Pb 등이 검출되었고, Zn은 검출되지 않았다. 부식화합물은 $PbCO_3$(고착물), $Cu_{1.96}S$(소지금속)이 나타났다. 따라서 서산 비경도 출수 상평통보의 혐기성 부식 특성은 탈아연, 황화동, 납화합물 세 가지로 요약할 수 있다.

• 한국가스학회지
• /
• 제8권1호
• /
• pp.1-6
• /
• 2004

선박용 열교환기의 냉각수로 사용되고 있는 해수의 입구온도는 스팀터빈콘덴서의 경우 약 $25^{\circ}C$이고 출구온도는 약 $60^{\circ}C$이며, 오일쿨러의 경우 출구온도는 약 $40^{\circ}C$이다. 이러한 해수의 온도 변화는 열교환기 세관재의 부식특성에 크게 영향을 미친다. 그러므로 부식손상을 최소화하면서 열교환 효율을 최대로 유지할 수 있는 냉각용액의 온도설정은 매우 중요하다. 따라서 본 연구에서는 $3.5\%$ NaCl + $0.1\%\;NH_4OH$ 수용액의 유동하에서 선박용 열교환기 세관재로 사용되고 있는 Al-황동의 분극 및 응력부식균열 실험을 실시하여 분극특성, 응력부식균열거동 및 탈아연특성에 미치는 용액의 온도의 영향에 대하여 고찰하였다.

• 한국안전학회지
• /
• 제19권2호
• /
• pp.1-5
• /
• 2004

Al-brass is the raw material of mnufacturing tubes for heat exchanger of vessel where seawater is used to coolant because it has high level of heat coductivity and excellent mechanical properties and high level of corrosion resistance due to cuprous oxide($Cu_2O$) layer against seawater. However, damage of Al-brass tubes for heat exchanger of vessel is reported that local corrosion such as stress corrosion cracking occurred by synergism effect between mechanical factor and corrosion environment. In this study, to investigate on the effect of stress on the polarization characteristics of Al-brass. At the stress of 0% and 95% yield strength by constant displacement tester, in 3.5% NaCl + 0.1% $NH_4OH$ solution, the polarization tests were carried out. And thus open circuit potential, corrosion current density, anodic polarization, cyclic polarization and dezincification behavior of Al-brass are investigated.

• 자원리싸이클링
• /
• 제7권2호
• /
• pp.23-30
• /
• 1998

제철소의 고로에서 발생하는 슬러지로부터 산화철 및 탄소분과 같은 유용 성분을 회수하여 리싸이클링하기 위하여 슬러지의 물리화학적 특성과 습식 사이클론을 이용한 분급특성을 조사형T다. 슬러지 입자의 크기에 따른 성분의 부존 상태를 조사한 결과, 탄소는 graphite 상으로 주로 굵은 입자에, 아연은 zinc sulfide로서 주로 미세한 입자에 분포하였다. 그러나 슬러지 중에 hematite 및 magnetite 상으로 존재하는 철분은 입경에 따른 편석이 없었다. 내경 75mm인 습식 사이클론에서 적정한 조건으로 고로슬러지를 분급하면 저아연 슬러지의 회수율과 탈아연율이 각 67.9~73.6% 및 72.7~86.8% 수준에 도달하였다.

• Corrosion Science and Technology
• /
• 제15권6호
• /
• pp.311-313
• /
• 2016

The anodic dissolution behavior of copper and brass in an electrolyte solution of 0.5M NaCl containing 0.5 mM $NaHCO_3$ was investigated by electrochemical impedance spectroscopy. The Nyquist plots of the copper impedance described a small loop in the high-frequency range and a large locus in the low-frequency range. Additionally, the features of the impedance spectrum of the brass were similar to those of the copper. This indicates that the copper-enriched layer formed on the brass surface due to the selective dissolution of the zinc from the surface. In addition, the rest potential and the anodic polarization curve for each sample were measured in order to discuss the selective dissolution of the zinc from the brass surface.