• Korean Journal of Hydrosciences
• /
• v.6
• /
• pp.23-37
• /
• 1995

In this experimental paper, the maximum scour depth at pier was student. The model of the pier of San Gye bridge in the Bocheong stream was set for the experimental studies. Several model verification processes were conducted through the roughness comparisons between model and prototype, pursuing scour depth variations with time depending upon channel bed variation, the comparison of the ratios between falling velocities and shear velocities in the model and prototype, and the comparison of pier scour depths between experimental data and field measuring data. The experiments were conducted in the free flow conditions and pressure flow conditions. The maximum scour depth at piers in the pressure flow conditions is almost twice as much as compared to the free flow conditions. Also, the maximum scour depth variations are indicated in the figures based on the Froude numbers, opening ratios, water depths and approaching angles in the free surface flow conditions.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.2
• /
• pp.1-10
• /
• 1997

The interaction of ground ice features with underlying seabed is one of the major considerations in the design of Arctic pipeline systems. Regarding the development of offshore gas field near Sakhalin Island, which is an ice-infested area, in this paper an ice scour model to determine the burial depth of Arctic offshore pipeline is studied. Using a simplified ice-seabed interaction process, ice scour depth is easily estimated. This nonlinear numerical model can simulate the scouring process for various enviromental parameters such as ice mass, incoming velocity, soil strength. This study also deals with interaction forces during the scouring process in sloping seabed conditions and discusses the ice loads that are transmitted through the seabed soil.

• Journal of Animal Environmental Science
• /
• v.8 no.2
• /
• pp.99-106
• /
• 2002

This study was conducted to improve utilization efficiency of slurry and choose a suitable type of tractor power which can be attached by manure spreader in the paddy field. In the paddy field, the pulling force for the spreader was measured by using a measurement system installed between tractors with and without the spreader. The soil moisture contents at the 0${\sim}$10cm and 10${\sim}$20cm depth of test soil(SiCL) were 28.45% d.b. and 23.47% d.b., respectively in average while Cone Index at l0cm and 15cm depth were 14.5kPa and 16.2kPa, respectively. It was impossible to measure the soil moisture contents and Cone Index below 20cm depth of the soil because the hardness of the soil increased greatly. Thereafter, hard pan of the sampled soil was found at 15${\sim}$20cm depth. While the required power only for the dragged tractor was found to be 3.44kW in the test field, the required pulling powers of tractor considering the pumping were 8.48${\sim}$12.48kW, 12.19${\sim}$16.19kW, 16.96${\sim}$20.96kW, respectively for 2 tons, 3 tons, and 4 tons of tank capacity. As the tank capacity increased, the sinkage of soil were also increased to 7cm, l0cm, and 12cm, respectively for the tractors with 2 tons, 3 tons and 4 tons of tank capacity. Considering about 60% of pulling efficiency of tractor, a tractor which had lower than 25.74kW of pulling power was suitable to pull the spreader and spread the slurry simultaneously for manure spreader with 2 tons of tank capacity. 29.42kW${\sim}$36.78kW of pulling power was found to be optimum for the tractor with 3 tons of tank capacity while over 40.45kW for 4 tons of tank capacity.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.3
• /
• pp.43-50
• /
• 1998

In the use of CNC machine tool, the unmanned production system has been growing in the manufacturing field. Thus, it is necessary to monitor adequate tool fracture during the cutting process efficiently. This experimental study is intended to investigate the development of flank wear in sysnchronous turning of differential materials(Aℓ/GC) which is used in industrial application and it is acknowledged as a machine to difficult material. In cutting process change of velocity, change of feed, and change of depth of cut were investigated on the effect of flank wear, and slenderness ratio is also investigated. The conclusions of this paper are summarized as follows; 1.Under the high cutting speed condition, the flank wear is affected by the feed and depth of cut. but the influence of feed on the flank wear is larger than the depth of cut and that is reduced when the velocity is low. 2.Under the high cutting speed, as the smaller slenderness ratio is, the shorter tool life is under the lower cutting speed, the effect of slenderness ratio on the flank wear is low. 3.Using the characteristics of cutting force, the flank wear of a tool can be detected 4. Investigating the development of flank wear, there are almost no differences between the characteristics of cutting force and feed force. Finally, these data from the differntial materials cutting process will be used in the basic field of precision and economic cutting process.

• Geomechanics and Engineering
• /
• v.31 no.5
• /
• pp.489-503
• /
• 2022

A 1257-m-long irregular deep foundation pit located in the central of Nanjing, China was constructed using the combined full-width and half-width top-down method. Based on the long-term field monitoring data, this study analyzed the evolution characteristics of the vertical movement of the columns, internal force of the struts, and axial force of the structural beam and slab. The relevance of the three mentioned above and their relationship with the excavation process, structural system, and geological conditions were also investigated. The results showed that the column uplift was within the range of 0.08% to 0.22% of the excavation depth, and the embedded depth ratio of the diaphragm wall and the bottom heave affected significantly on the column uplift. The differential settlement between the column and diaphragm wall remained unchanged after the base slab was cast. The final settlement of the diaphragm wall was twice the column uplift. The internal force of the struts did not varied monotonically but was related to numerous factors such as the excavation depth, number of struts, and environmental conditions. Additionally, the dynamic force and deformation of the columns, beams, and slabs were analyzed to investigate the inherent relationship and variation patterns of the responses of different parts of the structure.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.10
• /
• pp.4968-4986
• /
• 2017

In this paper, we primarily address the difficulty of automatic generation of a plausible depth map from a single image in an unstructured environment. The aim is to extrapolate a depth map with a more correct, rich, and distinct depth order, which is both quantitatively accurate as well as visually pleasing. Our technique, which is fundamentally based on a preexisting DepthTransfer algorithm, transfers depth information at the level of superpixels. This occurs within a framework that replaces a pixel basis with one of instance-based learning. A vital superpixels feature enhancing matching precision is posterior incorporation of predictive semantic labels into the depth extraction procedure. Finally, a modified Cross Bilateral Filter is leveraged to augment the final depth field. For training and evaluation, experiments were conducted using the Make3D Range Image Dataset and vividly demonstrate that this depth estimation method outperforms state-of-the-art methods for the correlation coefficient metric, mean log10 error and root mean squared error, and achieves comparable performance for the average relative error metric in both efficacy and computational efficiency. This approach can be utilized to automatically convert 2D images into stereo for 3D visualization, producing anaglyph images that are visually superior in realism and simultaneously more immersive.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2002.10a
• /
• pp.477-480
• /
• 2002

The purpose of this study Was to investigate the effects of ponding depth treatment on water balance in paddy fields. Three ponding depth treatment, shallow, traditional, and deep were used. Daily values of rainfall amount, ponding depth, irrigation water, drainage water, evapotranspiration, and infiltration were measureed in the field. The results showed that irrigation water depths were 198mm, 195mm, and 355mm in shallow, traditional, and deep ponding, respectively. The three treatments did not show any statistical difference in growth and yields. Shallow depth treatment showed the largest yield.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1851-1856
• /
• 2008

A numerical program based on computational fluid dynamics has been developed to simulate characteristics of an EHD induction micropump. The ambiguity of boundary conditions was removed by adopting an equation formulated for electric potential as the dependent variable. The calculations show that the dependency of frequency agrees well with the experiments and the previous analysis. The instability, caused by backflows, is getting stronger as the channel depth increases, which is consistent with experiments. The present study reveals that it is due to the limit in the penetration depth which the electric field can affect. Despite the disadvantage of large channel depth, there is a certain optimal depth for the maximum flow rate.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2000.10a
• /
• pp.138-143
• /
• 2000

CREAMS-PADDY model for simulating daily water and nutrient balance at irrigated paddies was developed, applied to, and validated with field data. The model simulates daily flooding depth and total nitrogen and phosphorus concentrations from meterorological, irrigation, and farming data. Simulated results from the model were in good agreement with field data. Among different scenarios to reduce nutrient losses from paddies, the water management was found to be very effective, and recommended for field applications.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.1
• /
• pp.10-19
• /
• 2010

As a series of studies about improvement of yellow croaker drift gill net fishing gear and development of the labor saving fishing system, this study analyzed the behavior characteristics of fishing gear, which does use three types of different sinker materials in the field tests. The result of maritime performance test indicated that the fishing gear which used the lead reached the maximum depth and bio ceramics hauled to the surface of water the fastest. The correlation between the sinking time (St) and depth (Dsl, Dsc, Dsb) of maritime performance test can be shown such experimental equations as Dsl=2.70St - 0.75, Dsc = 2.38St - 1.15, Dsb = 1.77St - 4.00. The correlation between the hauling time (Ht) and depth (Dhl, Dhc, Dhb) of maritime performance test can be shown such experimental equations as and Dhl = 7.88Ht + 35.48, Dhc = 7.80Ht + 40.01, Dhb = 7.95Ht + 36.44.