• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2008년도 정보통신설비 학술대회
• /
• pp.389-393
• /
• 2008

OFDM (Orthogonal Frequency Division Multiplexing) modulation using the orthogonal subcarriers reduces the delay spread by increasing robustness to multipath fading and can use overlapped bandwidth due to orthogonality on frequency domain. Thus data rate and spectral efficiency are increased. Because of these reason, OFDM is used for high speed data transmission for multimedia transmission as HSDPA, WiBro, WLAN. However OFDM also has drawbacks that have the high PAPR (Peak to Average Power Ratio). This high PAPR takes place because of parallel processing a number of data at once using a FFT processor. By high PAPR, amplifier doesn't act in dynamic range, so that BER performance is worse. In this paper, we reduce the PAPR using SLM(Selective Mapping). SLM doesn't effect on BER performance, but should transmit the side information for demodulation [2]. Also PAPR is higher as the number of FFT processor is larger. Thus SLM has high complexity. In this paper, we analyze the performance of SLM using scaling for no side information.

• 한국정보통신학회논문지
• /
• 제12권4호
• /
• pp.730-736
• /
• 2008

기존의 크리스탈 주파수 발진기는 주파수를 자유롭게 변경하지 못할 뿐만 아니라 이들 사이의 동기화에 대한 어려움이 존재한다. 이를 극복하는 새로운 디지털 복조 회로(DDC; Digital Demodulation Circuit) 시스템을 제안하고 이를 구현하였다. 구현한 디지털 복조 회로는 소수점 두 자리까지 자유롭게 주파수를 생성할 수 있다. 또한 레이저 거리 계측기에서 사용하는 많은 소자들이 요구하는 주파수 클록 생성과 오차 저감이 가능하여 고정밀 거리 측정이 가능한 시스템에 적용할 수 있다.

• Journal of Information Processing Systems
• /
• 제15권3호
• /
• pp.670-681
• /
• 2019

Orthogonal frequency division multiplexing (OFDM) is a system which is used to encode data using multiple carriers instead of the traditional single carrier system. This method improves the spectral efficiency (optimum use of bandwidth). It also lessens the effect of fading and intersymbol interference (ISI). In 1995, digital audio broadcast (DAB) adopted OFDM as the first standard using OFDM. Later in 1997, it was adopted for digital video broadcast (DVB). Currently, it has been adopted for WiMAX and LTE standards. In this project, a Verilog design is employed to implement an OFDM transmitter (DAC block) and receiver (FFT and ADC block). Generally, OFDM uses FFT and IFFT for modulation and demodulation. In this paper, 16-point FFT decimation-in-frequency (DIF) with the radix-2 algorithm and direct summation method have been analyzed. ADC and DAC in OFDM are used for conversion of the signal from analog to digital or vice-versa has also been analyzed. All the designs are simulated using Verilog on ModelSim simulator. The result generated from the FFT block after Verilog simulation has also been verified with MATLAB.

• 한국멀티미디어학회논문지
• /
• 제22권9호
• /
• pp.1011-1019
• /
• 2019

In this paper, we propose a system that can more precisely identify and monitor the position of the tool used in the assembling workplace such as automobile production. The proposed positioning monitoring system is a combination of UWB communication module and MEMS IMU sensor. Since UWB does not need modulation and demodulation function and has low power density, UWB is widely used in indoor positioning field. However, it may cause positioning error due to errors in RF transmission and reception process, which may cause positioning accuracy. Therefore, in this paper, we propose an algorithm that uses IMU as an auxiliary means to compensate for errors that may occur in positioning using only UWB. The tag and anchor of UWB module measure the transmission / reception time by transmitting signals to each other and then estimate the distance between tag and anchor. The MEMS IMU sensor serves to provide positioning calibration information. The tag, which is a mobile node and attached to a moving tool, measures the three-dimensional position of the tool and transfers the coordinate data to the anchor. Thus, it is possible to confirm whether or not the specific tool is properly used according to the prescribed regulations.

• 방송공학회논문지
• /
• 제24권3호
• /
• pp.485-494
• /
• 2019

주파수 변조 방식의 방송 주파수에 동조되는 안테나와 Realtek 사(社)의 RTL2832 칩을 이용하는 디지털 TV용 튜너와 아날로그-디지털 변환기로 구성되는 universal serial bus (USB) 동글을 이용하여 스테레오 주파수 변조 방송의 실시간 수신기를 컴퓨터의 소프트웨어로 구현한다. 아날로그 방송 신호가 USB 동글에서 디지털 신호로 변환되고 이진 데이터를 컴퓨터에서 매트랩 및 파이선 프로그래밍 언어의 신호처리 기법을 이용하여 저역 통과 필터, 대역 통과 필터, 주파수 판별기, 양측파대 진폭 복조, 위상 고정 루프. 샘플링 변환, 디앰퍼시스 등의 기능 블록을 설계한다. 최종적으로 수신기의 실시간 구현을 위하여 파이선 및 C++로 구성되는 그누라디오 (GNU Radio)를 이용하여 수신기 알고리즘을 소프트웨어로 구현한다.

• Journal of Positioning, Navigation, and Timing
• /
• 제10권4호
• /
• pp.307-313
• /
• 2021

Modernized GNSS signal structures tend to use tiered codes, and all GNSSs use binary codes as secondary codes. However, recently, signals using polyphase codes such as Zadoff-Chu sequence have been proposed, and are expected to be utilized in GNSS. For example, there is Tiered Differential Polyphase Code (TDPC) using polyphase code as secondary code. In TDPC, the phase of secondary code changes every one period of the primary code and a time-variant error is added to the carrier tracking error, so carrier tracking ambiguity exists until the secondary code phase is found. Since the carrier tracking ambiguity cannot be solved using the general GNSS receiver architecture, a new receiver architecture is required. Therefore, in this paper, we describe the carrier tracking ambiguity and its cause in signal tracking, and propose a receiver structure that can solve it. In order to prove the proposed receiver structure, we provide three signal tracking results. The first is the differential decoding result (secondary code sync) using the general GNSS receiver structure and the proposed receiver structure. The second is the IQ diagram before and after multiplying the secondary code demodulation when carrier tracking ambiguity is solved using the proposed receiver structure. The third is the carrier tracking result of the legacy GPS (L1 C/A) signal and the signal using TDPC.

• International Journal of Computer Science & Network Security
• /
• 제23권5호
• /
• pp.121-127
• /
• 2023

A 500 km/h linear motor high speed terrestrial transportation service is planned to launch 2027 in Japan. In order to support 5G service in the train, the Sub-carrier spacing frequency of 30 kHz is planned to be used instead of common 15 kHz sub-carrier spacing to mitigate Doppler effect in such high-speed transportation. In addition, to increase the cell size of 5G mobile system, plural Base Station antenna will transmit the identical Down Link (DL) signal to form the expanded cell size along the train rail. In this situation, forward and backward antenna signals will be Doppler shifted by reverse direction respectively and the receiver in the train might suffer to estimate accurate Channel Transfer Function (CTF) for its demodulation. In this paper, Delay and Doppler Profiler (DDP) based Channel Estimator is proposed and it is successfully implemented in signal processing simulation system. Then the simulated performances are compared with the conventional Time domain linear interpolated estimator. According to the simulation results, QPSK modulation can be used even under severe channel condition such as 500 km/h, 2 path reverse Doppler Shift condition, although QPSK modulation can be used less than 200 km/h with conventional Channel estimator.

• 대한임베디드공학회논문지
• /
• 제18권6호
• /
• pp.277-283
• /
• 2023

Vital signals provide essential information regarding the health status of individuals, thereby contributing to health management and medical research. Present monitoring methods, such as ECGs (Electrocardiograms) and smartwatches, demand proximity and fixed postures, which limit their applicability. To address this, Non-contact vital signal measurement methods, such as CW (Continuous-Wave) radar, have emerged as a solution. However, unwanted signal components and a stepwise processing approach lead to errors and limitations in heart rate detection. To overcome these issues, this study introduces an integrated neural network approach that combines noise removal, demodulation, and dominant-frequency detection into a unified process. The neural network employed for signal processing in this research adopts a MLP (Multi-Layer Perceptron) architecture, which analyzes the in-phase and quadrature signals collected within a specified time window, using two distinct input layers. The training of the neural network utilizes CW radar signals and reference heart rates obtained from the ECG. In the experimental evaluation, networks trained on different datasets were compared, and their performance was assessed based on loss and frequency accuracy. The proposed methodology exhibits substantial potential for achieving precise vital signals through non-contact measurements, effectively mitigating the limitations of existing methodologies.

• 대한전자공학회논문지TC
• /
• 제47권8호
• /
• pp.24-31
• /
• 2010

본 논문에서는 IEEE 802.15.4a chirp spread spectrum (CSS) 를 위한 저복잡도 수신기 구조를 제안한다. 무선 통신 시스템에서는 일반적으로 수신기의 신호 수신시 최대 SNR (Signal to Noise power Ratio) 을 보장하는 정합필터를 사용하여 신호를 복조를 하는 것이 일반적이다. 하지만, 정합필터는 하드웨어 복잡도가 높아 저복잡도, 저가격의 센서 네트워크를 목적으로 하는 CSS에서는 적합하지 않다. 따라서 본 논문에서는 정합필터를 사용하지 않고 인접 심볼 간 차등 곱셈과 누적을 통하여 chirp 신호를 복조하는 새로운 수신기 구조를 제안한다. 또한, CSS에 사용되는 이원 직교 코드의 특성을 이용하여 곱셈기를 사용하지 않은 이원 직교 디코더 구조를 제안한다. 제안하는 수신기 구조는 정합필터 기반 구조에 비하여 BER (Bit Error Rate) 성능은 떨어지지만 하드웨어 구현을 위한 곱셈기, 가/감산기, 레지스터 등의 자원의 수를 절감하였다.

• 한국음향학회지
• /
• 제23권1호
• /
• pp.24-29
• /
• 2004

최근에 OAT(Ocean Acoustic Tomography) 분야에서 M-시퀀스를 이용한 펄스압축 (pulse compression) 기법을 이용하여 해양 구조를 분석하는 많은 연구가 이뤄지고 있다. M-시퀀스는 정합필터 (matched-filter)을 사용한 복조를 통해. 훌륭한 시간 분해능 (resolution) 및 도플러 분해능을 제공할 수 있다. 또한 수신 신호를 적절하게 처리함으로써 수신기 출력의 신호대잡음비 성능을 개선할 수 있으며, 수신 신호를 동기적으로 평균하는 것은 그것에 대한 좋은 예라고 할 수 있다. 그리고 데이터를 빠르고 효율적으로 처리할 수 있는 FHT (Fast Hadamard Transform) 또는 FFT (Fast Fourier Transform) 기법을 사용함으로써 처리 속도를 효율적으로 개선할 수 있다. 본 논문에서는 동해 연안에서 수집된 데이터를 이용하여 수중 음파의 다중경로 성분과 지연 시간을 분석하며, 송수신기간의 샘플링 속도 오차에서 비롯된 현상을 설명하고 오차를 보상하는 방법을 제시한다. 그리고 채널의 scattering 함수, 지연 전력 프로파일 (delay power profile), 시간 확산 특성 등을 통하여 해양 음향 채널의 특성을 분석하도록 한다.