• Journal of Welding and Joining
• /
• 제28권2호
• /
• pp.39-46
• /
• 2010

IIn this study, used is the equivalent loading method based on the inherent strain to predict the welding deformation of panel members. Equivalent loads are computed from the inherent strain distribution around weld line, and then applied for the linear finite element analysis. Thermal deformation of panel members can be, of course, carried out through the rigorous thermal elasto-plastic analysis procedure but it is not practical in applying to predicting the welding deformation of large structures such as blocks found in a ship structure from view of computing time. The present equivalent load approach has been applied to flat plate model to verify the present approach, and to several curved plate models having the curvature in the welding direction to investigate the effect of the longitudinal curvature upon the weld-induced deformation. The results are compared with those by thermal elasto-plastic analysis. As far as the present results are concerned, it can be said that the present approach shows good agreement with the results by welding experiment and the rigorous thermal elasto-plastic analysis. The present approach has been also applied to predict the welding deformation of panel block as for application illustration to practical model.

• 소성∙가공
• /
• 제26권4호
• /
• pp.228-233
• /
• 2017

In flat rolling mills, demands for precise process set-up and control are increasing than ever before. Consequently, it is imperative to establish a novel approach, which would provide valuable information regarding the detailed aspects of deformation behavior of the strip, and rolls during rolling. In this paper, we present a finite element (FE) approach for 3-D coupled analysis of the elastic-plastic deformation of the strip and the elastic deformation of rolls in the roll-stack of a mill stand.

• 대한수학회지
• /
• 제40권4호
• /
• pp.709-725
• /
• 2003

We give an analytic approach to the versal deformation of a resolution of a germ of normal isolated singularities. In this paper, we treat only formal deformation theory and it is applied to complete the CR-description of the simultaneous resolution of a cone eve. a rational curve of degree n in P$^{n}$ (n $\leq$ 4).

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회 3차
• /
• pp.61-65
• /
• 2010

The performance of slopes during earthquake is often accessed in terms of permanent deformation. In the assessment of permanent deformation, Newmark-type rigid block analysis is widely used. Original Newmark-type block approach, however, assumes the potential sliding mass to be rigid, and has been criticized to be potentially unconservative. The paper reviews analytically the impact of this noncompliance assumption on computed permanent deformations. The results indicate that there is a simple criterion that can be used to determine the level of conservativeness of the rigid block approach in cases of gently-sloping slip surfaces and retaining walls.

• 소성∙가공
• /
• 제8권5호
• /
• pp.507-519
• /
• 1999

An approach using the energy method has veen proposed for the analysis of cone spinning having the complicated deformation modes mixed by shear and normal deformation. In the proposed method, the corresponding solution is found through optimization of the total energy dissipation with respect to the parameters assumed by the velocity field defined as the variation of the length in longitudinal direction. The sheet blank is divided into three layers to consider the bending effect and the energy dissipated by shear deformation is superposed to the energy consumption due to normal deformation related with the shrinking deformation is superposed to the energy consumption due to normal deformation related with the shrinking deformation of axi-symmetric sheet element for the evaluation of total deformation energy. In order to check the validity of the proposed method, the complex spinning for making the conical cup is analyzed and the computed results are compared with the experimental results. In comparison of the computed results with existing experimental results,, the good agreement is obtained for the variation of outer radius and the distribution of thickness, and it has thus been shown that the present approach is applicable to the analysis of complex spinning.

• 소성∙가공
• /
• 제26권4호
• /
• pp.234-239
• /
• 2017

A general approach is proposed for 3-D coupled FE analysis of the deformation of the strip and rolls in flat rolling. FE formulation, schemes for the treatment of contact occurring in a cluster of deforming objects, and the solution strategy are described in detail. The validity of the approach is examined through comparison with observed measurements. The approach is applied to the analysis of deformation in a four-high and six-high mill.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.295-298
• /
• 2005

High temperature deformation behavior of $\alpha\;and\;\beta$ phase of Ti-6Al-4V was investigated within the framework of a self-consistent approach at various temperature ranges. To examine the flow behavior of u-phase, Ti-7.0Al-1.5V alloy was used, whose chemical composition is close to that of the $\alpha$ phase in Ti-6Al-4V at hot working temperatures. The flow stress of $\beta$ phase was predicted by using self-consistent approach. The flow stress of $\alpha$ phase was higher than that of $\beta$ phase above $750^{\circ}C$, while the $\beta$ phase revealed higher flow stress than a phase at $650^{\circ}C$. It was found that the relative strength and strain rate ratio between $\alpha\;and\;\beta$ phase significantly varied with temperature. From this approach, the mode for grain matrix deformation was proposed as a mixed type of both iso-stress and iso-strain rate modes.

• 대한기계학회논문집A
• /
• 제27권4호
• /
• pp.507-514
• /
• 2003

Most of CAE analyses for injection molding have been based on the Mele Shaw's approximation: two-dimensional flow analysis. in some cases, that approximation causes significant errors due to loss of the geometrical information as well as simplification of the flow characteristics in the thickness direction. Although injection molding analysis software using three-dimensional solid elements has been developed recently, such as Moldflow Flow3D, it does not contain a deformation analysis function yet. The present work covers three-dimensional deformation analysis or injection molded plastic parts using solid elements. A numerical scheme for deformation analysis has bun proposed from the results of injection molding analysis using Moldflow Flow3D. The accuracy of the proposed approach has been verified through a numerical analysis of rectangular plates with various thicknesses in comparison with the classical shell-based approach. In addition, the reliability of the approach has also been proved through an industrial example. an optical plastic lens, in comparison of real experiments.

• 한국지반공학회논문집
• /
• 제23권3호
• /
• pp.15-24
• /
• 2007

본 논문은 도로기초 입상재료의 응력의존적인 특성을 고려한 응력의존적 재료 상수의 적용을 통하여 층 변형예측을 수행하는 간편한 방식을 소개한다. 이 방법은 Unbound지반재료에 대하여 회복변형과 영구변형을 구분하여 고려하며 두 변형의 상호작용을 적용하지 않는 방식이다. 그 결과 회복변형 탄성계수와 포와송비를 포함한 해석모형은 상호작용이 고려되지 않아도 현장에서의 도로기초 변형을 예측할 수 있음을 잘 보여주고 있다. 또한 응력의존 탄성계수와 응력의존 포와송 비 모형에서 가장 영향을 많이 미치는 계수를 찾기 위하여 민감도분석을 실시하였다. 이러한 분석결과를 토대로 응력의존에 의하여 변형 예측시 나타나는 경향을 살펴보았다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.186-189
• /
• 2004

Although magnesium has high potential for structural material due to the lightweight and high specific strength, the structural application has been limited by the low ductility at room temperature. The reason of the poor ductility is few activated slip systems of magnesium (HCP structure) during deformation. As temperature increases, however, additional non-basal slip systems are incorporated to exhibit higher ductility comparable to aluminum. In the present study, a series of tensile tests of Mg-Al alloy has been carried out to study deformation behavior with temperature variation. Analysis of load relaxation test results based on internal variable approach gave information about relationship between the micromechanical character and corresponding deformation behavior of magnesium. Especially, the material parameter, p representing dislocation permeability through barriers was altered from 0.1 to 0.15 as the non-basal slip systems were activated at high temperature.