• Computers and Concrete
• /
• 제25권4호
• /
• pp.303-310
• /
• 2020

In this research, a hybrid mathematical model is derived using the higher-order polynomial kinematic model in association with soft computing technique for the prediction of best fiber volume fractions and the minimal mass of the layered composite structure. The optimal values are predicted further by taking the frequency parameter as the constraint and the projected values utilized for the computation of the eigenvalue and deflections. The optimal mass of the total layered composite and the corresponding optimal volume fractions are evaluated using the particle swarm optimization by constraining the arbitrary frequency value as mass/volume minimization functions. The degree of accuracy of the optimal model has been proven through the comparison study with published well-known research data. Further, the predicted values of volume fractions are incurred for the evaluation of the eigenvalue and the deflection data of the composite structure. To obtain the structural responses i.e. vibrational frequency and the central deflections the proposed higher-order polynomial FE model adopted. Finally, a series of numerical experimentations are carried out using the optimal fibre volume fraction for the prediction of the optimal frequencies and deflections including associated structural parameter.

• 한국안전학회지
• /
• 제34권5호
• /
• pp.103-110
• /
• 2019

In order to reduce the accidents occurring at construction sites, it is necessary to approach with harmonious measures considering various aspects such as systems, training, facilities, and protection equipments. Suggestion of safe construction method can be a good alternative. In the previous study, the half-depth precast deck with RC rib panel was proposed as an alternative method for safe bridge deck construction, and the performance required by the design code was verified through a four-point bending test. But the actual bridge deck is subjected to the repetitive action of the wheel load rather than the bending condition due to the four-point load. In this study, fatigue test was performed by repeating the wheel load $2{\times}10^6$ cycles to verify the safety of the half-depth precast deck with RC rib panel under actual conditions. As a result, fatigue effect due to repetition of wheel load was not significant in terms of serviceability such as crack width and deflection. In the residual strength test conducted after the fatigue test, the half-depth precast deck with RC rib panel failed by punching shear which is typical failure mode of bridge decks and the residual strength was similar to the punching strength of the RC and PSC bridge decks in spite of the fatigue effects.

• 한국안전학회지
• /
• 제34권4호
• /
• pp.76-84
• /
• 2019

The precast pannels are used as formwork in Half-depth precast deck systems. Therefore, it has many advantages, including safe and convenient construction and reduced construction period compared to cast-in-place construction method. In half-depth precast deck systems, the bonding of precast pannels to cast-in place concrete is very important. To enhance the performance of half-depth precast deck system, it is necessary to improve the composite efficiency of the interface or increase the stiffness of the precast pannel to reduce deformation or stress on the interface. In this study, a flexural test of half-depth precast deck system was performed, in which the shear connecting reinforcement was applied to increase the bonding performance at the interface, and the rib shape precast panels were applied to improve stiffness. In addition, the safety and serviceability of these systems were evaluated. Test results show that all of specimens have the required flexural strength under the ultimate strength limit design. It was also evaluated to have sufficient safety for the serviceability of deflection and crack under the serviceability limit design.

• 한국공간구조학회논문집
• /
• 제20권4호
• /
• pp.131-139
• /
• 2020

In this paper, the hybrid prefabricated retrofit method is suggested and examined. Six specimens were manufactured in order to evaluate their flexural performance of RC beams. Test parameters include the added beam depth, the thickness of bottom plate, the number of the steel plate with openings. The effects of these parameters on the flexural performance of reinforced concrete beams were examined. The load-deflection behavior and modes of cracks are presented from the test results. At the test result, the flexural capacity and the ductility of the hybrid prefabricated retrofit method was increased satbly. Also, comparing the flexural performance of RC beam and retrofitted RC beams, it was increased that the flexural strength is about 3.3 times, the ductility is about 2.55 times, and energy dissipation capacity is about 7.34 times.

• Computers and Concrete
• /
• 제28권5호
• /
• pp.487-495
• /
• 2021

The use of prestressed concrete box girder bridges built by segmentally balanced cantilevers has bloomed in the last decades due to its significant structural and construction advantages in complex topographies. In Colombia, this typology is the most common solution for structures with spans ranging of 80-200 m. Despite its popularity, excessive deflections in bridges worldwide evidenced that time-dependent effects were underestimated. This problem has led to the constant updating of the creep and shrinkage models in international code standards. Differences observed between design processes of box girder bridges of the Colombian code and Eurocode, led to the need for a validation of in-service status of these structures. This study analyzes the long-term behavior of the Tablazo bridge with data scarcity. The measured leveling of this structure is compared with a finite-element model that consider the most widely used creep and shrinkage models in the literature. Finally, an adjusted model evidence excessive deflection on the bridge after six years. Monitoring of this bridge typology in Colombia and updating of the current design code is recommended.

• 한국산업융합학회 논문집
• /
• 제25권6_3호
• /
• pp.1165-1171
• /
• 2022

In this paper, the results of an experimental study were presented by measuring and comparing the flexural strength and deformation on the carbon fiber sheet strength reinforced concrete beam considering end anchorage effect. For this purpose, total six specimens of 100×100×600mm size were prepared and tested according to the KDS 14 20 20. The specimens were categorized in three cases as reference beams without strengthening, beams carbon fiber strengthened but not anchored and beams carbon fiber strengthened also anchored. Experimental results showed that the end anchorage contributed to increase the flexural strength about 42% greater than that of carbon fiber sheets alone, and the number and width of cracks were relatively increased. The results support a considerable effects of end anchorage for carbon fiber strengthened reinforced concrete beams in enhancing the flexural performance. Further studies are needed in durability and long term behavior of carbon fiber sheet strengthened reinforced concrete beams.

• Geomechanics and Engineering
• /
• 제30권6호
• /
• pp.579-586
• /
• 2022

Pile-supported structures are installed on saturated sloping grounds, where the ground stiffness may decrease due to liquefaction during earthquakes. Thus, it is important to consider saturated sloping ground and pile interactions. In this study, we conduct a centrifuge test of a pile-supported structure, and analyze the p-y_p loops, p-y_p loops provide the correlation between the lateral pile deflection (y_p) and lateral soil resistance (p). In the dry sand model (UV67), the p-y_p loops stiffness increased as ground depth increased, and the p-y_p loops stiffness was larger by approximately three times when the pile moved to the upslope direction, compared with when it moved to the downslope direction. In contrast, no significant difference was observed in the stiffness with the ground depth and pile moving direction in the saturated sand model (SV69). Furthermore, we identify the unstable zone based on the result of the lateral soil resistance (p). In the case of the SV69 model, the maximum depth of the unstable zone is five times larger than that of the dry sand model, and it was found that the saturated sand model was affected significantly by kinematic forces due to slope failure.

• 항공우주시스템공학회지
• /
• 제16권1호
• /
• pp.81-85
• /
• 2022

본 연구에서 항공기 엔진의 공기흡입구 복합재 적용 구조 설계 및 해석 연구를 수행하였다. 본 연구에서 설계를 위해 대상 구조물의 구조 설계 요구조건 분석을 수행하였다. 구조 설계 하중은 압력 분포 하중과 가속도 조건을 적용하였다. 구조 설게 결과를 검증하기 위한 구조 안전성 평가를 위해 유한 요소 해석이 수행되었다. 구조 안전성 평가를 위해 응력 해석, 변형 해석, 좌굴 해석이 수행되었다. 최종 구조 안전성 검토를 통해 설계된 공기흡입구는 안전성을 확보한 것으로 확인되었다.

• 한국지진공학회논문집
• /
• 제1권2호
• /
• pp.79-89
• /
• 1997

본 연구에서는 Haringx 이론에 근거하여 면진용 적층고무베어링의 기계적 역학특성을 살펴보고자 한다. 이를 위하여 제안된 수평강성 평가식을 검토하고 점성감쇠의 영향을 분석하기 위한 점탄성문제로의 확장을 통해 감쇠증폭을 역학특성을 평가하였다. 그리고 적층고무베어링에 대한 좌굴안정성평가를 수행하여 형상계수의 양향을 분석하였다. P-delta 효과를 고려한 적층고무베어링의 수평가성식을 면지구조물의 지진해석에 적용하여 동적잔단변형응답 해석결과를 실제 진동대를 이용한 실험결과와 비교하였다. 본 연구로부터 제안된 단순 수평강성 평가식은 설계수직하중내에서 적용가능하며 점탄성문제로 쉽게 확장이 가능하다. 좌굴안정식 평가로부터 적층고무베어링은 단일 고무판의 두께 증가비에 비하여 총 고무판두께 증가비가 좌굴하중감소에 크게 영향을 준다. 그리고 입력지진에 대한 면진구조물의 해석결과 적층고무베어링의 전단변형응답이 실제 실험결과와 매우 일치한 결과를 얻었다.

• Carbon letters
• /
• 제6권4호
• /
• pp.234-242
• /
• 2005

Bending and tensile properties of 2D cross-ply C/C composites with processing heat treatment temperature (HTT) are evaluated. C/C composites used are made from two types of PAN based T700 and M40 carbon fibers with phenolic resin as carbon matrix precursor. Both the types of composites are heat treated at different temperatures (ranging from 750 to $2800^{\circ}C$) and characterized for bending and tensile properties. It is observed that, real density and open porosity increases with HTT, however, bulk density does show remarkable change. The real density and open porosity are higher in case T-700 carbon fiber composites at $2800^{\circ}C$, even though the density of M40 carbon fiber is higher. Bending strength is considerably greater than tensile strength through out the processing HTT due to the different mode of fracture. The bending and tensile strength decreases in both composites on $1000^{\circ}C$ which attributed to decrease in bulk density, thereafter with increase in HTT, bending and tensile strength increases. The maximum strength is in T700 fiber based composites at HTT $1500^{\circ}C$ and in M40 fiber based composites at HTT $2500^{\circ}C$. After attending the maximum value of strength in both types of composite at deflection HTT, after that strength decreases continuously. Decrease in strength is due to the degradation of fiber properties and in-situ fiber damages in the composite. The maximum carbon fiber strength realization in C/C composites is possible at a temperature that is same of fiber HTT. It has been found first time that the bending strength more or less 1.55 times higher in T700 fiber composites and in M40 fiber composites bending strength is 1.2 times higher than that of tensile strength of C/C composites.