• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.4
• /
• pp.4218-4225
• /
• 1976

To insure the safety of the drainage sluice, topogrophical change due to erosion as well as capability of discharging the design flow in a very important factor. In consideration of the fact that the drainage sluice is built in the sea, its construction has many topographically restricted problems and naturally requires a completeness of research and experiment. This thesis is a comparative and analytic study of discharging flow acting on the erosion at the bottom of the structure on the basis of the measured velocity on the downstream channel of the drainage sluice. (1) The measured velocity shows a little higher values than the computed velocity, because the measured velocity was observed at the surface of the stream. There fore, it is reasonable that the compated velocity should be taken in this study. (2) The field observation was conducted to have the measurement of the flow velocity without surveying the area of flow. Therefore, the coefficient of discharge could not be computed. The survey of the area of flow is planned to be conducted along with the measurement of the flow velocity. (3) The apron of the drainage sluice is free discharging type and it was designed to be about 80m in length less than it should be. (4) The apron of free flow discharging type should have a solid foundation to protect the structure by preventing erosion damage to upstream and downstream channels against weathering of rock and strong torrent. Whether free flow discharging type or energy-dissipating type is best chosen depends on the topographical condition of the forage site, therefore, there would be a comparative study before the final decision was made about the protrection for the structure. (5) It is considered to be appropriate that the design and construction of the drainage sluice should have a complete study which is based on hydraulie model test before the type of protection is decided. (6) It is much requested that a variety of experiment equipments be installed and observed to study the protection for the drainage sluice.

• Journal of Astronomy and Space Sciences
• /
• v.34 no.4
• /
• pp.315-330
• /
• 2017

Halo coronal mass ejections (CMEs) originating from solar activities give rise to geomagnetic storms when they reach the Earth. Variations in the geomagnetic field during a geomagnetic storm can damage satellites, communication systems, electrical power grids, and power systems, and induce currents. Therefore, automated techniques for detecting and analyzing halo CMEs have been eliciting increasing attention for the monitoring and prediction of the space weather environment. In this study, we developed an algorithm to sense and detect halo CMEs using large angle and spectrometric coronagraph (LASCO) C3 coronagraph images from the solar and heliospheric observatory (SOHO) satellite. In addition, we developed an image processing technique to derive the morphological and dynamical characteristics of halo CMEs, namely, the source location, width, actual CME speed, and arrival time at a 21.5 solar radius. The proposed halo CME automatic analysis model was validated using a model of the past three halo CME events. As a result, a solar event that occurred at 03:38 UT on Mar. 23, 2014 was predicted to arrive at Earth at 23:00 UT on Mar. 25, whereas the actual arrival time was at 04:30 UT on Mar. 26, which is a difference of 5 hr and 30 min. In addition, a solar event that occurred at 12:55 UT on Apr. 18, 2014 was estimated to arrive at Earth at 16:00 UT on Apr. 20, which is 4 hr ahead of the actual arrival time of 20:00 UT on the same day. However, the estimation error was reduced significantly compared to the ENLIL model. As a further study, the model will be applied to many more events for validation and testing, and after such tests are completed, on-line service will be provided at the Korean Space Weather Center to detect halo CMEs and derive the model parameters.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.3
• /
• pp.405-413
• /
• 2013

Monocyte chemotactic protein-3 (MCP-3), a chemokine that is in a superfamily of structurally related small chemotactic cytokines involved in leukocyte trafficking, is regarded as a key factor in atherogenesis. In this study, we examined the changes in atherogenic parameters including hepatic lipid accumulation and oxidative balance in MCP- 3-overexpressing transgenic mice (MCP-3 mice) under atherogenic conditions. To induce an extreme atherogenic condition, mice were fed a high-fat, high-cholesterol (HFHC) diet for 12 weeks. The body weight and food intake were not changed by MCP-3 overexpression in the aorta. On a HFHC diet, the MCP-3 mice had higher plasma levels of total cholesterol and a higher atherogenic index compared with wild-type mice, although there were no differences in the plasma HDL-cholesterol and triglyceride levels. Furthermore, an increase in lipid accumulation was observed in the aortas as well as the livers of the HFHC diet-fed MCP-3 mice compared with wild-type mice. The activities of antioxidant enzymes increased in the livers of the HFHC diet-fed MCP-3 mice, whereas supplementation with antioxidants, naringin and hesperidin, reversed the activities of the hepatic antioxidant enzymes in HFHC diet-fed MCP-3 mice, indicating that there might be more oxidative damage to the tissues in the HFHC diet-fed MCP-3 mice leading to progression towards atherosclerosis and hepatic steatosis. Microarray analyses of the aorta revealed atherosclerosis-, PPARs-, lipoprotein receptor, and apolipoprotein-related genes that were affected by the HFHC diet in MCP-3 mice. These findings suggest that aortic MCP-3 overexpression may contribute to the development of atherosclerosis and hepatic steatosis under atherogenic conditions.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.153-153
• /
• 2016

Aluminum alloys have poor corrosion resistance compared to the pure aluminum due to the additive elements. Thus, anodizing technology artificially generating thick oxide films are widely applied nowadays in order to improve corrosion resistance. Anodizing is one of the surface modification techniques, which is commercially applicable to a large surface at a low price. However, most studies up to now have focused on its commercialization with hardly any research on the assessment and improvement of the physical characteristics of the anodized films. Therefore, this study aims to select the optimum temperature of sulfuric electrolyte to perform excellent corrosion resistance in the harsh marine environment through electrochemical experiment in the sea water upon generating porous films by variating the temperatures of sulfuric electrolyte. To fabricate uniform porous film of 5083 aluminum alloy, we conducted electro-polishing under the 25 V at $5^{\circ}C$ condition for three minutes using mixed solution of ethanol (95 %) and perchloric (70 %) acid with volume ratio of 4:1. Afterward, the first step surface modification was performed using sulfuric acid as an electrolyte where the electrolyte concentration was maintained at 10 vol.% by using a jacketed beaker. For anode, 5083 aluminum alloy with thickness of 5 mm and size of $2cm{\times}2cm$ was used, while platinum electrode was used for cathode. The distance between the two was maintained at 3 cm. Afterward, the irregular oxide film that was created in the first step surface modification was removed. For the second step surface modification process (identical to the step 1), etching was performed using mixture of chromic acid (1.8 wt.%) and phosphoric acid (6 wt.%) at $60^{\circ}C$ temperature for 30 minutes. Anodic polarization test was performed at scan rate of 2 mV/s up to +3.0 V vs open circuit potential in natural seawater. Surface morphology was compared using 3D analysis microscope to observe the damage behavior. As a result, the case of surface modification presented a significantly lower corrosion current density than that without modification, indicating excellent corrosion resistance.

• Journal of the Korea Safety Management & Science
• /
• v.9 no.1
• /
• pp.197-211
• /
• 2007

The power of semiconductor, Korea is continuously constructing semiconductor production line for keeping a front-runner status. however, studies and data about potential risks in semiconductor factory are still short. If fire does not initially suppressed, the fire causes a great damage. To decrease fire risk factors, in addition to fire fighting safety equipment, more important thing is how to design and construct fire protection system. The current fire protection codes about semiconductor factory come under functional law, and this law is short of consideration about particularity of factory. The existing prescriptive fire codes depending on experience compose without evident engineering verifications, thus equipments which is created by the current prescriptive fire code may bring about a variety of problems. For example, the design under the current regulation can not cope with the excessive investments, low efficiencies, and the diversifying construction designs and be applied to the quick changes of new technologies. Ergo, an optimal design for fire protection is to equip fire protection arrangements with condition and environment of production field. Manufacturing factory of semiconductors is a windowless airtight space. And for cleanliness, there exists strong flow of cooperation. Therefore, there is a need for fire safety design that meets the characteristic of a clean room. Accordingly, we are to derive smoke flow according to cooperation process within a clean room and construction plan of an optimal sensor system. In this study, in order to confirm the performance of proposed smoke-exhaust equipment and suggest efficient smoke exhaust device when there is a fire of 1MW of methane in the clean room of company H, we have implemented fire simulation using fluid dynamics computation.

• Journal of Arbitration Studies
• /
• v.18 no.1
• /
• pp.31-47
• /
• 2008

An arbitrator's duty shall be independence and impartiality such as a judge who has procedurally absolute position. Independence is the freedom from others, impartiality is the status of having no-partial condition. Although these show relevance between independence and impartiality, in actuality, it is not easy to prove them. Therefore, arbitrator has to prove his or her position by opening the public of reality and by having an obligation of notification. Each country which applies Arbitration rules or Arbitration act stays the same as Korean Commercial Arbitration Board does. Hence, each country has the moral principles in order to establish a standard of judgement for essential factors and requests preferentially the impartiality and the publicity. In reality, court of justice in England excludes arbitrator who has the close relation to a person concerned. Justice in France cancelled an authorization of arbitrator because of having the economic interest to the person concerned. And also, In United States, Federal Court reverses an arbitration judgment without giving any partiality to a person concerned because of not opening a public about the relationship between arbitrator and a person concerned. Therefore, decision basis of the independence and the impartiality is standardized by the economic interest of a person concerned, professional relation, society connection, relationship between arbitrator and arbitration representative in the same case while in process of arbitration, arbitrator's nationality If arbitrator does not keep the independence and the impartiality by a position of judge, he or she has to make responsible. this duty is divided by two things: civil case and crime case. and if arbitrator does break this responsibility, he or she will get the cancellation of judge and compensation of damage. However, Korea is placed in the real circumstance without judge precedent and moral principles including the independence and impartiality. In order to getting the good reputation of international arbitration institution, this country will have to enact principles of the independence and impartiality for arbitrator.

• Korean journal of applied entomology
• /
• v.43 no.1
• /
• pp.27-34
• /
• 2004

This study was conducted to develop optimal control tactics of the northern root-knot nematode, Meloidogyne hapla, using cultural method and biological agents ｛Bacillus thuringiensis (Bt), Paecilomyces lilacinus and plant extract (Huhjunl)｝ in the fields of Codonopsis lanceolata. Germination of C. lanceolata was susceptible to fosthiazate, but not to Bt or a plant extract. In pot assay, the inhibitory effect of two microbial agents, Bt and Paecilomyces lilacinus, on M. hapla were significant, but less than that of fosthiazate. The plant extract also had significantly inhibitory effect on M. hapla. In field assay, treatments of P lilacinus and fosthiazate resulted in maximal yields and qualities of C. lanceolata. The effect of the plant extract on the yields of C. lanceolata was also better than no treatment. The nematode-occurring condition of the fields before transplanting had significant effect on development of C. lanceolata; nematode-occurring field type gave less yields than nematode-free field type. These results suggest that a cultural control technique using paddy field, microbial pesticides using Bt or P lilacinus, and the plant extract are the promising control tactics against M. hapla in C. lanceolata fields. As a field manual to decrease economical damage of C. lanceolata due to M. hapla, this study suggests that C. lanceolata can be cultured directly in paddy field or in upland field after nematode control using microbial agents or the plant extract.

• Journal of Environmental Science International
• /
• v.19 no.1
• /
• pp.69-80
• /
• 2010

Today's fundamental purpose of environmental education is to fulfill people's desire of living in a pleasant environment and at the same time promoting individualistic and collective environmentally friendly behaviors. In order to achieve these purposes, it is very important that each person holds an environmentally friendly mind that constantly tries to preserve and protect the environment which should be acquired through experiencing the importance of the environment. In order to increases the sense of attachment of people and the natural environment, the direction of environmental education should carry out education on environment related knowledge and the condition of environment damage side by side. The direction of environmental education should consider the cultivating student's awareness for active participation on matters related to the environment and to change their behaviors towards the environment. This study has tested the effect of reflective writing activities about the environment on the environmental sensitivity and willingness to act of 5th grade primary school students. For the sole purpose of this study, 70 students out of 141 5th graders of M Primary School were divided as the experimental group, and another 71 students were divided as the control group. The experimental group participated in 10 activities in where they were asked to express their thoughts and feelings in writing regarding 10 environmental problems occurring near the M Primary School. The control group participated in 10 environmental education lectures focusing on the lecturer. The results were as following. First, the reflective writing activities about the environment were effective in the environmental sensitivity of primary school students. Second, the reflective writing activities about the environment can affect the environmental willingness to act of primary school students. Third, there was a statistically significant correlation between environmental sensitivity and environmental willingness to act.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.5
• /
• pp.836-842
• /
• 2016

When an accident occurs in the nuclear power plant, the faulted information might mislead to the high possibility of aggravating the accident. At the Fukushima accident, the operators misunderstood that there was no core exposure despite in the processing of core damage, because the instrument information of the reactor water level was provided to the operators optimistically other than the actual situation. Thus, this misunderstanding actually caused to much confusions on the rapid countermeasure on the accident, and then resulted in multiplying the accident propagation. It is necessary to be equipped with the function that informs operators the status of instrument integrity in real time. If plant operators verify that the instruments are working properly during accident conditions, they are able to make a decision more safely. In this study, we have performed various tests for the fault detection sensitivity of an data-driven empirical model to review the usability of the model in the accident conditions. The test was performed by using simulation data from the compact nuclear simulator that is numerically simulated to PWR type nuclear power plant. As a result of the test, the proposed model has shown good performance for detecting the specified instrument faults during normal plant conditions. Although the instrument fault detection sensitivity during plant accident conditions is lower than that during normal condition, the data-drive empirical model can be detected an instrument fault during early stage of plant accidents.

• Korean Chemical Engineering Research
• /
• v.53 no.4
• /
• pp.431-439
• /
• 2015

The methods which decrease the accident hazards of LPG(Liquefied Petroleum Gas) terminal on the basis of butane & propane storage tanks by applying HAZOP(Hazard and Operability), LOPA(Layer of Protection Analysis) and SIL(Safety Integrity Level) are suggested. The accident scenarios were derived by analyzing latent risks through the HAZOP. The scenarios which would have the big damage effect in accidents were selected and then LOPA was assessed by analyzing IPL(Independent Protection Layer) about the correspond accident scenarios. The improved methods were proposed on the basis of level of SIF(Safety Instrumented Functions) as a IPL considering satisfied condition of risk tolerance criteria($1.0{\times}10^{-05}/y$). In addition, The proposed IPLs were basis on the economic analysis. The effect of SIF as a IPL considering the changes of accident frequency was studied in case of the accident scenarios derived from the concerned process.