• Wind and Structures
• /
• v.29 no.1
• /
• pp.43-53
• /
• 2019

Vortex-induced vibration of three circular cylinders (each of diameter D) in an equilateral triangular arrangement is investigated using the immersed boundary method. The cylinders, with one placed upstream and the other two side-by-side downstream, are free to vibrate in the cross-flow direction. The cylinder center-to-center spacing L is adopted as L/D = 2.0. Other parameters include the Reynolds number Re = 100, mass ratio $m^*=2.0$, reduced velocity $U_r=2{\sim}15$ and damping ratio ${\zeta}=0$. Cylinder vibration responses are dependent on $U_r$ and classified into five regimes, i.e. Regime I ($U_r{\leq}3.2$), Regime II ($3.2<U_r{\leq}5.0$), Regime III ($5.0<U_r{\leq}6.4$), Regime IV ($6.4<U_r{\leq}9.2$) and Regime V ($U_r>9.2$). Different facets of vibration amplitude, hydrodynamic forces, wake patterns and displacement spectra are extracted and presented in detail for each regime.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2019.05a
• /
• pp.607-609
• /
• 2019

The split-channel two-tone OOK method proposed in this paper can improve the communication performance of IoT in fading channel environment. The frequency diversity effect can be obtained by separating the interval of the two tone signals, and a performance gain of 8 dB can be obtained in the fading channel. In addition, by using split-channel, the problem of degradation of the channel bandwidth efficiency caused by the frequency diversity technique can be prevented, thereby reducing the bandwidth efficiency by allocating the remaining frequency channels to other users.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.11
• /
• pp.39-51
• /
• 2009

This is a study on rectangular-shaped passive row piles in inclined sand-ground by model tests. The experiment controlled the angle of inclination of ground and induced the ground destruction. We also measured the behavior of row piles, by adjusting the shape, position and spacing of piles. As a result, we confirmed the earth pressure, the lateral resistance, and the effect of depressing on the ground variation working on passive pile. The effect of B-type pile of which the front width is wide is bigger than that of H-type pile of which the side width is wide. We can find out the failure angle of slope, the shared force of pile and soil by using the lateral resistance graph based on slope angle.

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.3
• /
• pp.861-864
• /
• 2024

The self-driving roller conveyor system, which transports target products by controlling multiple rollers with a motor, is a logistics system suitable for branching and joining logistics and controlling the alignment of target products, and its utilization is increasing, especially in the food manufacturing process. In this paper, we build a simulation environment using Unity software based on 3D graphic modeling of a self-driving roller conveyor system. In a situation where target products are supplied irregularly in terms of time, a method is proposed that can align products to maintain constant spacing by controlling the rollers. Simulation results show that effective alignment of products is possible by controlling the motor that drives the roller based on sensor data of the product position.

• Journal of the Optical Society of Korea
• /
• v.10 no.3
• /
• pp.112-117
• /
• 2006

We experimentally investigated the transmission characteristics of 400 Gbit/s (10 Gbit/s ${\times}$ 40 channels) WDM signals with 100 GHz channel spacing over 323 km of installed NZ_DSF. The installed fiber has optical properties of 0.28 dB/km attenuation, 4.3 ps/nm/km dispersion, $0.083ps/nm^2/km$ dispersion slope and less than $0.05ps/km^{1/2}$ PMD coefficient. In this experiment, two cases of dispersion compensation schemes, the lumped type and the distributed type, were compared. The results implied that the distributed type dispersion compensation in which dispersion compensation devices are inserted at the end of the each span showed better transmission performance than the lumped one in which dispersion compensation devices are located at the transmitter and receiver sites. From the analysis of the experimental results, we verified that different transmission performance comes from the power penalty induced by XPM in the distributed scheme is lower than the lumped scheme case.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.04a
• /
• pp.37-39
• /
• 2008

The purpose of this study is to improve the defects of DPP fabric by heat setting and to describe the change of physical properties of DPP fabrics. The thermosetting was carried out in autoclave from 100 to 140$^{\circ}C$ temperature range for 10min.. In this study, we investigated the effect of the thermosetting temperatures on the structural, thermal, mechanical properties and dyeability of DPP fabrics. The melting peak of multi peak changed to single peak with an increased thermosetting temperatures. The melting energy(J/g), the tensile strength and elongation were found to increase with increasing temperature of heat setting. The diffraction peak at Bragg angle(2${\theta}$) about 13.8$^{\circ}$ were very strong, and diffraction intensity, d-spacing and half-width decreased with increasing thermosetting temperatures. On the other hand, the dyeability(K/S) and crease recovery decreased with an increasing thermosetting temperatures.

• 전기의세계
• /
• v.30 no.5
• /
• pp.306-312
• /
• 1981

The Townsend discharge domain is generally observed with stable positive characteristics in N$_{2}$ gas discharge at low pressures differently in the others, which transfer immediately to glow dischage after self-sustaining discharge starts. In this paper, the presence of the stable Townsend discharge, applied voltage-discharge current characteristics and the effect of disgased electrode surface on stable townsend discharge are studied experimentaly in N$_{2}$ gas mixed with 0.05% of No in volume. As the result of this experiment, the stable Townssend discharge is observed only in pure nitrogen with the valve of pd.geq.8[torr.cm] (p=gas pressure, d=gap spacing), but not in gas mixtures. This is considered that No gas in gas mixtures disexcites effectively the metestble state of nitrogen.

• ETRI Journal
• /
• v.36 no.3
• /
• pp.361-366
• /
• 2014

In this paper, a new, simple capacitive tilt sensor with a metallic ball is proposed. The proposed tilt sensor has only two electrodes and a metallic ball, and this design assists in managing the inherent contact problem in measuring tilt angles. Capacitive sensing, compared with other types of tilt sensor, has many advantages such as simplicity, noncontact measurement, long-throw linear displacement, and sub-micron plate spacing. Its design and fabrication process are significantly simpler than previous types of tilt sensors. The dimensions of the prototype tilt sensor are $20mm{\times}20mm$, and the diameter of the polystyrene tube is 5 mm with a tube thickness of 0.15 mm. An analytical study of the prototype capacitive tilt sensor was undertaken, and the experimental results demonstrate the relationship between the tilt angles and measured capacitances compared with the analytical study.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.148-148
• /
• 2003

질석(vermiculite)을 출발물질로 하여 30$0^{\circ}C$에서 4시간 열처리하여 습식분쇄하고 325mesh 이하의 입자를 선별하여 수열조건에서 양이온 계면활성제인 hexadecyl trimethylammonium bromide (C$_{16}$TABr)를 층간 삽입시켜 유기화 질석을 제조하였다. 생성물을 XRD, TGA, FT-IR 등을 이용하여 분석하였고, 합성 및 층간 삽입조건을 조사하였다. 질석에 $C_{16}$TABr를 층간 삽입을 확인하기 위하여 XRD 분석 결과 d-spacing 값이 9.6$\AA$에서 33.5$\AA$으로 증가됨을 확인하였고, 열중량 시험결과 출발물질과 비교하여 유기화 질석은 25%감량이 확인되었다. 위 결과 값으로부터 질석의 유기화 처리로 인하여 층간 간격이 확장되었음을 확인하였다. 일반적으로 층간 간격이 넓을수록 고분자가 층 사이에 보다 쉽게 삽입될 수 있으며 고분자 매트릭스 안에서 층상화합물의 분산 및 박리가 용이해진다. 따라서 본 연구 결과로부터 합성된 유기화 질석은 고분자 나노복합재로 사용 가능성을 제시하고 있다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.116-119
• /
• 2004

The use of higher strength materials frequently requires the change of design provisions. Following to the previous researches, high strength reinforcing bars have a weak point about the development and splice length. Based on the previous research about high relative rib area, bond strength between reinforcing bars and concrete can be improved by the control of rib height and spacing. But, the code provisions do not include these specific shape of reinforcing bars. So, the purpose of this paper is to determine the effect of relative rib area to the bond strength. This paper describes the experiment and analysis of 5 beam-spliced specimens containing D25 with relative rib areas ranging from 0.073 to 0.17. The test results are also analyzed to make a design formula about the calculation of splice length on the consideration of relative rib area.