• Journal of Korean Society of Forest Science
• /
• v.103 no.3
• /
• pp.402-407
• /
• 2014

In this study, Italy poplar(Populus euramericana) was selected for test specimen to measure cutting power when it harvested. The experiment has been controlled as three levels of feed rate (0.41, 1.25 and 2.5 m/s), sawing speed (800, 1,000 and 1,200 rpm), and the five levels of root collar diameter (50, 70, 90 and 110, 130 mm). The harvested volume after 3 years (root collar diameter 50 mm) was 10.5 tons, which falls short of the target amount of biomass is 20~30 ton/ha. In addition, the biomass amount of diameter 90 and 110 mm which reached the target amount were estimated to be 23.5 and 32.5 ton/ha respectively. As a result of experiment, it was found out that power of 128.2 and 175.8 W are consumed in case of cutting with the feed rate of 0.41m/s and minimum sawing speed (800 rpm) respectively. With the working area of 0.3 ha/h, it is considered to present working capacities of 16.5 and 22.8 ton/h respectively. The power consumed at the feed rate of 1.25 m/s is estimated to be 113.8 and 153.7W respectively and working capacity in a working area of 1 ha/h is estimated to be 23.5 and 32.5 ton/h. The power consumed at the feed rate of 2.5 m/s is estimated to be 119.8 and 166.9 W respectively and working capacity in a working area of 2 ha/h is estimated to be 47.0 and 65.5 ton/ha respectively. Therefore, the power source of harvest machine at the feed rate of 1.25, 2.50 m/s and sawing speed of 800 rpm shall be selected as it can process the target amount of estimated biomass.

• Horticultural Science & Technology
• /
• v.30 no.4
• /
• pp.449-462
• /
• 2012

The objectives of this study were to measure the range of motion for joints and muscle activation of upper limb for flower arrangement tasks for physical rehabilitation and to test horticultural therapy programs using flower arrangement tasks for improving upper limb function of the patients with stroke. Major flower arrangement tasks were classified with eight tasks (cutting 1, thick stem; cutting 2, thin stem; fixing 1, long stem; fixing 2, short stem; rolling a leaf; bending 1, thick stem; bending 2, thin stem; and winding, using a wire) based on the occupational analysis. When eight male university students (mean age $24.1{\pm}2.5$ years) conducted the eight flower arrangement tasks, range of motion for joints and muscle activation of upper limb were measured by a 3D motion analyzer and electromyography, respectively. Based on the results of the range of motion and muscle activation of upper limb, horticultural therapy programs using flower arrangement tasks (total 33 sessions) for improving upper limb function of the patients with stroke was conducted at a rehabilitation hospital, Seoul, South Korea and then the range of motion, grip strength, and upper limb function of the patients were tested. Among the eight flower arrangement tasks, cutting 1, winding, and bending 1 induced the highest value for the range of motion in joints of shoulder, elbow, and wrist, respectively (P < 0.001). In terms of muscle activation, eight flower arrangement tasks performed in this study showed various patterns of muscle activation and several muscles were simultaneously used for each task (P < 0.001). In addition, thickness and length of the materials used in a task had a prominent effect on the range of motion for joints and muscle activation of upper limb (P < 0.001). The stroke patients had positive effects for their range of motion of upper limb (shoulder, forearm, and elbow), grip strength, and overall upper limb function through the horticultural therapy program. Thus, this study suggested that flower arrangement tasks would be a potential horticultural activity for physical rehabilitation program. It would be interesting to apply a customized horticultural therapy program using flower arrangement tasks according to the symptoms of patient for physical rehabilitation.

• The Journal of Engineering Geology
• /
• v.26 no.4
• /
• pp.447-460
• /
• 2016

Samples of Hangdeung granite and Berea sandstone containing sliding planes were prepared by saw-cutting and polishing using #100 or #600 grinding powders. Their basic friction angles were then measured directly in direct shear tests and triaxial compression tests, and also in tilt tests, which measure the angles indirectly. Although the angles measured by the direct methods were generally accurate, those measured along certain planes were greatly different from the others depending on the condition of the plane. The tilt tests yielded similar angles regardless of the sliding plane condition or the rock type; however, the error range was relatively wide. Sliding planes polished by the grinding powders yielded more accurate results than those cut by the saw and tested without polishing, as polishing ensured consistent conditions among all the planes. Sliding planes polished using #100 grinding powder yielded better results than polishing with #600 grinding powder. Therefore, the basic friction angles measured along the sliding planes polished using #100 grinding powder, as obtained in direct shear and triaxial compression tests, were the most reliable. The angle could also be measured satisfactorily by tilt testing along sliding planes polished with #100 grinding powder.

• Korean Journal of Clinical Laboratory Science
• /
• v.50 no.3
• /
• pp.345-353
• /
• 2018

This study examined the associations of smoking, alcohol drinking habits and both with the carotid intima-media thickness (CIMT) in university students. This study was performed using a CAGE (test for alcohol: cutting down, annoyance by criticism, guilty feeling, and eye-openers) questionnaire, FTND (the Fagerstrom test for nicotine dependence) questionnaire, and CIMT of university students. No statistically significant differences were observed among the CIMT results according to each CAGE level classified into 3 groups. The results of CIMT according to the FTND smoking categorization showed that the smoking group was higher than nonsmoking group (P<0.01). A statistically significant difference was observed between the left and right CIMT regarding smoking and drinking (P<0.01). In the only drink risk group, the left CIMT (19.84 rank) showed a low-ranking. The CIMT on the left (42.38 rank) and right (42.81 rank) showed high scores in the group with only the risk of smoking (P<0.01). These results suggested that there are distinct differences in CIMT and relevant risk factors between smokers and drinkers, particularly among those with a high smoking status. This study had several limitations: the study population was small; the relatively young age of the study subjects; and limited of focus on smoking, drinking and CIMT. In conclusion, cigarette smoking significantly exacerbates the adverse effects and higher CIMT on the subclinical atherosclerosis risk in young adults, which underscores the importance of prevention and cessation of cigarette smoking in young adults.

• Journal of Conservation Science
• /
• v.25 no.3
• /
• pp.273-282
• /
• 2009

As a result of investigating research papers concerning the metal bound rim decoration on four pieces of 'Bowl, white porcelain with impressed floral design and sliver bound rim' and one piece of 'Bowl, white porcelain with sliver bound rim' from among the Jingdezhen white porcelain, which are Sinan remains that are kept in a National museum of Korea. It was found that the material of the bound rim was not silver but tin, and lacquer was used as glue. Based on such a scientific analysis, this study conducted a reproduction test of the manufacturing technique and the bonding method of the metal bound rim attached to the upper tip of the china ware. As a way of reproducing the bound rim, the study was able to discover the best method in terms of the avoidance of loss of materials and the workability out of various cutting methods for tin plates, and it also discovered that the use of lacquer in mixture with soil showed a better workability than the use only of a lacquer ingredient in a test of the bonding method of a metal bound rim using lacquer. Also, in the test of a drying method, a bonding method after drying within a short time at a relatively high temperature was found to be more effective than the drying method after humidifying at a normal temperature, which is used in traditional lacquer ware preservation treatment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.67-75
• /
• 2019

The diaphragm used for CFT columns has a small amount of steel to be used, but has a disadvantage that welding is difficult and openings are required because the steel tube and four sides must be welded. The improved diaphragm to be examined in this study was cut into four corners by cutting the center hole for concrete filling. In the improved diaphragm, the width of the center hole is the same as that of the previous diaphragm, but the width of the diaphragm contacting the steel tube is reduced, thereby reducing the welding length by about 70% compared to the previous diaphragm. The in-plane strain of each specimen was analyzed when the same load was applied to the interior diaphragm through a simple tensile test. Using the general FEM program(ANSYS 19.2), the analysis was performed under the same conditions as the actual simple tensile test, and the load transfer between the improved diaphragm and the previous diaphragm was compared. When the width of the diaphragm is equal to or smaller than the flange width, stress is concentrated from the end of the diaphragm, and when the flange width is larger, stress is concentrated at the center.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.2
• /
• pp.181-186
• /
• 2022

Dam slope RIM is a highly important contact interface where the main body and the base surface are connected. In general, when the grouting for the slope of the dam structure is designed, it is planned using limited data (drilling, geological map, etc.). This makes it very difficult to accurately consider the original ground characteristics of the slope RIM grouting target, In addition, when the grouting volume planned during the design is drilled and injected into the original ground where the waterstop is secured, there is a possibility that the original ground with the waterstop is disturbed and the effect of the waterstop is rather diminished. In order to overcome such problems, it is more suitable to first consider geological conditions and determine whether to perform optimal grouting on the original ground through on-site repair tests before performing RIM grouting. In this paper, to determine the grouting of the RIM unit, a pilot hole water pressure test was performed on the rock of the slope in the target section. The analysis shows grouting volume of 1 Lugeon or less, and the cement injection amount also shows the injection result of 1 kg/m or less. In this case, performing grouting is rather counterproductive. This result can be evaluated through a rock of which some degree of order of mass is secured, as it is a dam design standard of 1 Lugeon or less when analyzed, using the results of visual observation and geological map creation during slope cutting. Therefore, in conclusion, it is preferable to make the decision for using RIM grouting on the slope of the dam body structure, based on 1 Lugeon in a rock state, and the cement injection amount also at 1 kg/m.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.9
• /
• pp.5-16
• /
• 2012

In the case of using the soil materials created by cutting in-situ ground directly without adjusting particle size, it is recommendable to seek the compaction property or material constant required for filling design or density control through indoor test, and many studies on this subject have been carried out during that time. The researches conducted during that time, however, were focused on the mixed materials with different diameters that exist in a natural condition. There has been no study conducted using coal fly ash that is by-product of the thermal power plant that is actively considered as the building materials. Therefore, this study was aimed at implementing compaction test and examining the basic engineering property in order to explore the influence of crushing the particles through compacting the admixture of crushed stone and coal fly ash produced from thermal power plant on its engineering property, and then the impact of the admixture volume of each material on compaction property and material property by conducting the One-Dimensional Compression Test. As result of compaction test, the optimum moisture ratio of coal fly ash was shown to be approx. 23%. As result of compaction test in accordance with the mixed ratio of coal fly ash and crushed stone under the same compaction energy and moisture ratio, dry unit weight tended to drop when the mixed ratio of coal fly ash exceeded 30%, while it reached approx. $1.81gf/cm^3$ when the mixed ratio was 30%. As result of One-Dimensional Compression Test in accordance with the mixed ratio of crushed stone and coal fly ash, the change in void ratio by particle crushing was at the highest level in the case of coal fly ash 100%, while the lowest level in the case of crushed stone 100%. In the case of mixed materials of crushed stone and coal fly ash, compression index was at the lowest level in case of coal fly ash 30%, and therefore this ratio of mixed material was judged to be the most stable from an engineering aspect.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2090-2100
• /
• 2011

Railway rail fastening system is the critical device which gives big influences to not only the vehicle driving stability and the orbit's structural stability against the impulsive load, but also the noise vibration and the ride comfort. As a part of the low-carbon green growth, the importance of the railroad industry is getting highlights on its excellent energy-efficiency and eco-friendliness. However, so far the Korea's domestic rail fastening system technology is not so good and the technical reliance to abroad is very heavy. In this study, we conducted comparative analysis on the rail fastening system with new and used one of the same type. And those systems are imported by Seoul Metro and are being used by it. With this basis, we developed the components and the materials and then, established the durability assessment methods appropriate to the Korean domestic circumstances. And through the reliability qualification test on the 7 parts of the rail fastening system, we've improved the reliability and guaranteed the 15 years of service lifetime. ($B_{10}Life15$) Establishment and standardization of Reliability Standard on the parts of the rail fastening system such as anti-vibration pads, guide-plate, screw spike made it possible to perform the internationally fair assessment. And it is thought that we can satisfy the manufactures' and consumers' needs of cost-cutting and qualification security by shortening of assessment period on rail fastening system.

• Korean Journal of Human Ecology
• /
• v.21 no.3
• /
• pp.551-565
• /
• 2012

The primary goal of this study was to provide a systematic methodology of utilizing 3D technology for tight-fit performance sportswear using information of skin deformation in various posture. Technical tools used in this study are Cyberware whole body scanner, RapidForm2004, 2C-AN 3D pattern development program, and YukaCAD. Analysis of the 3D skin deformation while knee joint was bent from $0^{\circ}$ to $60^{\circ}$ revealed that the length of dermatomes L4 was remained consistent during knee bending. Therefore, L4 was chosen as a major cutting line. To develop a highly ergonomic pattern, replicas of static and dynamic postures were developed and integrated using two methods, one is morphing method (Sqirlz Morph), and the other is AutoCAD. Experimental tight-fit garments called 'Derm-Mov Pattern' was designed using dematomes L4, L2, and inner line under knee and compared with four other patterns. As results, AutoCAD was appropriate as a integrating method of various postures. In wear test, 'Derm-Mov Pattern' was rated high (p < .001), in terms of pressure comfort especially around front crotch area. However, wear sensation was not signipicantly different in other area due to highly extensible property of materials. Pressure distribution was relatively even in these experimental garments.