• Restorative Dentistry and Endodontics
• /
• v.33 no.3
• /
• pp.235-245
• /
• 2008

The aim of this study was to develop a method for measuring the slumping resistance of resin composites and to relate it to the rheological characteristics. Five commercial hybrid composites (Z100, Z250, DenFil, Tetric Ceram, ClearFil) and a nanofill composite (Z350) were used to make disc-shaped specimens of 2 mm thickness. An aluminum mold with square shaped cutting surface was pressed onto the composite discs to make standardized imprints. The imprints were light-cured either immediately (non-slumped) or after waiting for 3 minutes at $25{\circ}C$ (slumped). White stone replicas were made and then scanned for topography using a laser 3-D profilometer. Slumping resistance index (SRI) was defined as the ratio of the groove depth of the slumped specimen to that of the nonslumped specimen. The pre-cure viscoelasticity of each composite was evaluated by an oscillatory shear test and normal stress was measured by a squeeze test using a rheometer. Flow test was also performed using a flow tester. Correlation analysis was performed to investigate the relationship between the viscoelastic properties and the SRI. SRI varied between the six materials (Z100 < DenFil < Z250 < ClearFil < Tetric Ceram < Z350). The SRI was strongly correlated with the viscous (loss) shear modulus G' but not with the loss tangent. Also, slumping resistance was more closely related to the resistance to shear flow than to the normal stress. Slumping tendency could be quantified using the imprint method and SRI. The index may be applicable to evaluate the clinical handling characteristics of composites.

• Journal of the Korea Concrete Institute
• /
• v.16 no.4 s.82
• /
• pp.493-500
• /
• 2004

FREP(Fiber Reinforced Epoxy Panel) are used for strengthening the damaged RC beams due to its good tensile strength, low weight, resistance to corrosion, and easy applicability. This study sets up structure equation for FREP bending reinforcement before and during the usage of RC beam. It finds the difference and finds the mechanical characteristics of rip-off failure that is caused by stress concentration in reinforcement material cutting part to estimate the performance of bending reinforcement. The result of this research can be summarized as two main consequences. The main failure of FREP reinforced concrete beam is rip-off failure and it evaluated rip-off failure of RC reinforcing bean based on the test and analytical conditions of this study. It found that stress was concentrated due to rapid change of bending rigidity in reinforced cutting part as a result of excessive reinforcement thickness of FREP. It resulted in rip-off failure. It means that it should evaluate the rip-off failure when designing reinforcement. It analyzed the reinforcement effect according to reinforced period for FREP. It found that reinforcement effect of P-Type that was reinforced during the usage decreased compared to I-Type that was reinforced before the usage. So when reinforcing a existing structure that is being used, it should consider the stress that is produced due to the fixed load.

• The korean journal of orthodontics
• /
• v.39 no.4
• /
• pp.203-212
• /
• 2009

Objective: The aim of this study was to evaluate the strain induced in the cortical bone surrounding an orthodontic microimplant during insertion in a self-drilling manner. Methods: A 3D finite element method was used to simulate the insertion of a microimplant (AbsoAnchor SH1312-7, Dentos Co., Daegu, Korea) into 1 mm thick cortical bone. The shape and dimension of thread groove in the center of the cortical bone produced by the cutting flute at the apical of the microimplant was obtained from animal test using rabbit tibias. A total of 3,600 analysis steps was used to calculate the 10 turns and 5 mm advancement of the microimplant. A series of remesh in the cortical bone was allowed to accommodate the change in the geometry accompanied by the implant insertion. Results: Bone strains of well higher than 4,000 microstrain, the reported upper limit for normal bone remodeling, were observed in the peri-implant bone along the whole length of the microimplant. Level of strains in the vicinity of either the screw tip or the valley part were similar. Conclusions: Bone strains from a microimplant insertion in a self-drilling manner might have a negative impact on the physiological remodeling of cortical bone.

• Journal of the Korean Dietetic Association
• /
• v.4 no.2
• /
• pp.235-244
• /
• 1998

Hand washing is an important component of hygiene program for food handlers. Hands can be a source of direct or indirect contamination of foods with pathogenic microorganisms. In this study, the effectiveness of hand washing methods and the use of 70% alcohol solution against transient skin bacteria was tested in an university foodservice facility. 70% alcohol solution is sprayed for 5 seconds automatically when hands are placed in the dispenser. Samples were taken using swab technique in meat cutting area, vegetable trimming area, and vegetable cutting area: before and after washing hands according to planned methods, and after being sprayed with 70% alcohol solution after washing hands. The bacteriological analysis of total plate counts, coliform, fecal coliform of food handlers' hands was done. Statistical data analysis was completed with Mann-Whitney U test and Kruskal-Wallis model using the SPSS program. The levels of initial contamination of workers' hand were significantly different by the work areas($x^2$=9.156, p<0.01). Workers in the vegetable trimming area had more heavily soiled hands than in the other work areas. Mean of TPC counts and coliform was 8.97×$10^5$ CFU/12.4$cm^2$, 2.93×$10^2$ MPN/12.4$cm^2$ respectively, but fecal coliform was not detected. Transient bacteria were removed from hands after washing and using 70% alcohol solution but were not removed completely. Mean reduction percentage in TPC varied among work areas and ranged from 93.19% to 94.99%, and in coliforms from 97.31% to 100%. A significant difference in TPC was found between before and after hand disinfection (Z=-2.714, p<.01) and between standardized hand washing procedures and un-standardized hand washing procedures(z=-2.301, p<.01). Subjects using the hand sanitizer showed a great elimination of TPC(99.45% reduction), but this effect was valid only after following proper washing procedures. Based on the results, the most effective hand washing method was recommended as the combination of the standardized hand washing procedure with warm-water and use of the 70% alcohol solution. The results can be used to develop hand hygiene programs and training strategies for enhancing hand hygiene practices for food handlers in foodservice operations.

• Journal of the Korean Academy of Child and Adolescent Psychiatry
• /
• v.32 no.2
• /
• pp.71-78
• /
• 2021

Objectives: This study was conducted to investigate the reliability and validity of the Korean version of the DSM-5 Level 2 Cross-Cutting Symptom Measure-inattention [Swanson, Nolan and Pelham, version IV (SNAP-IV)] and anger [Patient-Reported Outcome Measurement Information System (PROMIS) Anger] for parents and guardians of children aged 6-17 years. Methods: We included 104 children and adolescents diagnosed with attention-deficit/hyperactivity disorder (ADHD), ADHD with anxiety and depression, depressive disorder, anxiety disorder, and tic disorder with somatic symptoms (ADHD=41, depression=9, anxiety=14, ADHD+anxious depression=11, tic+somatic symptoms=29). Their ages ranged from 8 years to 15 years. The participants' mothers completed the SNAP-IV, PROMIS Anger scale, Korean version of the IOWA Conners Rating Scale (K-IOWA), and Korean ADHD Rating Scale (K-ARS) so that the reliability and validity of the SNAP-IV and PROMIS Anger scales, which are DSM-5 scales for assessing inattention and anger of children and adolescents, could be examined. Results: The reliability coefficient of SNAP-IV (Cronbach's α) was 0.94. The correlation coefficients between SNAP-IV, K-IOWA inattention, and K-ARS inattention scores ranged from 0.73 to 0.86. The mean SNAP-IV scores of the ADHD and the ADHD+anxious depression groups were significantly higher than those of the anxiety and the tic+somatic symptoms groups. The reliability coefficient of the PROMIS Anger was 0.91. The correlation coefficient between PROMIS Anger and K-IOWA oppositional/defiant scores was 0.75. The PROMIS Anger mean score of the ADHD+anxious depression group tended to be higher than that of the other groups. Conclusion: These results suggest that the Korean version of the DSM-5 Level 2 Cross-Cutting Symptom Measure-inattention and anger for parent and guardian of child age 6-17 might be a reliable and valid test and may be useful for screening children and adolescents with ADHD.

• The Journal of Engineering Geology
• /
• v.27 no.3
• /
• pp.255-265
• /
• 2017

We have determined the optimal pumping rate of the PW-2 water well (depth=100 m) at Imgokri, Sangju City. Cutting analysis and geophysical logging data reveal water-producing horizons at 26.1-26.5, 28.0-30.0, 33, 58, and 71 m. For pumping rates of 40, 55, 70, 90, and $132m^3/d$ over 70 days, the estimated drawdown from the PW-2 well was 6.48, 11.56, 18.07, 28.99 and 60.26 m, respectively. During a constant-rate pumping test at a rate of $117m^3/d$, the cone of depression intersected an impermeable boundary after 120-150 min of pumping. Therefore, we consider the critical pumping rate for well PW-2 to be $90m^3/d$. After pumping at $90m^3/d$ for 70 days, the calculated drawdown was 28.82-31.27 m. We suggest an optimal pumping rate for well PW-2 of $70-90m^3/d$, as the optimal pumping rate should be similar to the critical pumping rate. Sharp increases in the slope of the time-drawdown relationship, dissolved oxygen concentrations, and oxidation-reduction potential during the constant-rate pumping test indicate the limited development of bedrock aquifers around PW-2.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.3
• /
• pp.319-324
• /
• 2003

Statement of problem. Adhesives in dentistry playa major role in the success of restorative treatments. In the treatment of all ceramic restoration it is needed to find the adequate bond strength between enamel and dentin. Purpose. The purpose of this study was to evaluate shear bond strength of resin cement bonded to extracted human uncut enamel, cut enamel, and dentin in vitro. Material and methods. Ten freshly extracted anterior teeth without any previous restorative treatments were chosen. The extracted teeth were embedded in PMMA cold acrylic in the shape of a cylinder, 25 mm in diameter by 25 mm in height. The bonding system used was as follow: Uni-Etch (32% phosphoric acid), One-Step adhesive, Duolink resin cement. The specimens were acid etched and rinsed with water. Two layers of One-Step adhesive were coated with a disposable brush on the uncut enamel. VIP curing light at $500mV/cm^2$ was used to cure the adhesive. For cut enamel shear bond test, the specimen used for uncut enamel was further reduced approximately $0.3{\sim}0.5mm$ using a laminate preparation diamond bur (0.3 mm in depth). The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit SiC paper and cleaned with distilled water. The bonding procedure on the cut enamel was same as uncut enamel bonding procedure. For dentin bonding test, the specimen used for cut enamel was further reduced approximately $0.5mm{\sim}1.0mm$ using a laminate preparation diamond bur (0.5 mm in depth of diamond cutting). The amount of reduction was evaluated with the silicone mold. The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit silicon carbon paper and cleaned in distilled water. The bonding procedure on the dentin was same as uncut enamel bonding procedure. All samples were mounted and secured on the Ultradent shear bond test sample holder, and Ultradent restricted shear bond testing device was used with Universal Instron machine until fracture. Analysis of variance (ANOVA) test was performed comparing the result at P<0.05. Multiple comparison (Tukey) was used to compare each groups. Result. The result showed that the mean value in shear bond strength of resin cement bonded to uncut enamel, cut enamel and dentin were 27.04 Mpa, 30.25 Mpa and 26.39 Mpa with respect. Conclusion. Within the limitation of this study, the mean value of the shear bond strength of cut enamel was higher than those of uncut enamel or dentin. However there existed no statistical differences between three different human dentition substrates due to increased adhesive characteristics.

• Tunnel and Underground Space
• /
• v.33 no.1
• /
• pp.29-41
• /
• 2023

The brittleness of rocks plays an important role in determining the fragmentation and failure behavior of rock. However, there is still no standard method to evaluate the brittleness of rock, and previous studies have suggested the several definitions for estimation of brittleness of rock. Even in the process of mechanical rock excavation and drilling, the brittleness of rock is considered as an important property for evaluating the excavation efficiency of mechanical excavators or boreability of rock. The previous studies have been carried out to investigate the correlation between different brittleness of rock and cutting efficiency and boreability of rock. This study introduced a method for calculating the brittleness of rock from punch penetration test, and analyzed the correlation between the brittleness of rock calculated by the uniaxial compressive and Brazilian tensile strengths and that from punch penetration test. From the results of correlation analysis, the relationship between various brittleness was confirmed, and it was found that PSI and BI₃ showed a good correlation with the strength-based brittleness index. In addition, the results indicated that B₃ and B₄ are suitable to represent the brittleness of rock in the field of mechanical rock excavation.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.14 no.3
• /
• pp.2703-2715
• /
• 1972

1. Title of Research Research on the Loss of Irrigation Water Flowing in Earth Channel. 2. Purpose and Importance of Research The purpose of this research is to obtain the accurate loss rated of irrigation water flowing in earth channels so as to give a criterion of designing rational and effective suplpy project of irrigations water. It is the present status that the loss rates of 10 to 20% are obscurely applied without any scientific proof. Therefore, the importance of this research lies in securing loss rates, which are experimentally proves to be suitable for specific local conditions. 3. Content and Scope of Research The selected test reach of the main channel is 1,000m long. Discharges were measured at up and downstream enps by using current meter. The test reach of the lateral channel is 500m long, and parshall flumes were set at both ends to measure inflow and outflow. Finally, for the supply ditch, the test section is 200m long, and sharp-edged rectangular weirs were provided at both ends to measure inflow and outflow. In addition, various factors influence on the loss of irrigation water in channel wer examined. 4. Results of Research and Proposition Results: 1. In the main channel, which is 1,000 M long, and has a slope of 1/3,000 and was constructed by cutting earth, its loss rate is 9.64%. 2. In the lateral, which has a slope of 1/1,500, and is 500m long, and was constructed by cutting, its loss rate is 15.55%. Its average seepage rate is 2.08cm/day. 3. In the supply ditch, which has a slope of 1/300, and is 200m long, and was constructed by filling earth, its loss rate is 12.34%, its average seepage rate being 3.37cm/day. Proposition: As could be seen in the results above-mentioned, it is contradictory to apply a loss rate of 20% for every main channels and 15% for every laterals without variation, as done so for in planning irrigation project. The fact, however, is that loss rates must be different according to localities and characteristics. Due to the fact that this experiment is small in its scope and is nothing but a preliminary one, it is hardly possible to draw decisive conclusions with the results obtained in this research. Loss rates, that are secured through more extensive research, should be used, in order to establish precise irrigation project. Moreover, such researches should be carried out for a number of loclities throughout the nation.

• International Journal of Highway Engineering
• /
• v.13 no.1
• /
• pp.157-168
• /
• 2011

Recently, the cases of freeze-thaw distress on concrete pavement in domestic have been reported periodically. Hereupon, the necessity to establish the standard of spacing factor came to the fore. The test method for analyzing spacing factor is provided in the standard of ASTM C 457. Since researchers tend to judge study results subjectively, the results should be revised throughly. Image analysis program for determining the characteristics of air-void system on hardened concrete identify air void through the difference of a color. The pixel intensity values used in this program have a significant effect on the analysis results. This study compared the automated void count by varying pixel intensity values with the manual void count in order to determine the optimum range of pixel intensity values. Also, this study analyzed the air-void characteristics on eight kinds of concrete mixtures. In this study, it was confirmed that the variation of void counted manually was around 10% from the results of round robin test, and that the optimum range of pixel intensity values is around 80~90. And it was also confirmed that air content (as a whole) was increased generally and spacing factor was decreased by increasing air-entrainer content. But some concrete mixtures showed a tendency that air content was constant and spacing factor was decreased by increasing air-entrainer content. This causes the air entrained by air-entrainer has more influence on spacing factor than air content. Also, the deviation of spacing factor by cutting position of concrete specimen was about 30~100${\mu}m$ because of the limit of 2-D image analysis. The additional study about variation of spacing factor by cutting position of concrete specimen will be performed later.