• Journal of Ocean Engineering and Technology
• /
• v.15 no.1
• /
• pp.52-56
• /
• 2001

This study were looks at the effect of the initial cut length or stress concentration level, on the wave forms produced by crack propagation. The signals were collected, then classified visually for each type of sample. They were put into three classes according to their shapes in the time and frequency domain. Each class should domain signals which could be correlated to a certain micro-failure mechanism that occurs during the fatigue process. Classes of these signals compared, with each sample. To see if there were any classes common to the three samples. The fatigue test attempted to determine if the initial cut length has any influence on the type of signals.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.13 no.1
• /
• pp.45-50
• /
• 2006

Papers were prepared from cut cocoons and mulberry branches, which are byproducts from sericulture industry. The long filament of silk should be cut into appropriate length in order to prepare paper and this was achieved by chemical method. By a mixture of sodium hydroxide and sodium carbonate solution, the silk filaments were cut into short fibers (less than 1 mm in length). Since the short silk fibers (sSf) could not bind each other by itself, starch and poly(ethylene oxide)(PEO) were added as a bonding agent. When starch and PEO were used in a ratio of 3:7, the silk papers had optimum mechanical properties for paper. Fibers from the skin of mulberry branches (MBF) were added to sSf to enhance the mechanical properties of pure silk paper. Bleaching of MBF was performed with a mixture of hydrogen peroxide and sodium silicate. The mechanical properties were greatly enhanced and the optimum blend ratio of MBF and sSf were 7:3. The mulberry/silk paper has good absorption property against formaldehyde, and therefore, the paper could be applied as a wall paper for preventing the sick house syndrome.

• Journal of Biosystems Engineering
• /
• v.34 no.4
• /
• pp.228-233
• /
• 2009

In order to cut the round bale easily, a roughage cut-feeder for the round bale was developed in this study. This study consists of two parts. One is development of a cutting mechanism and a performance test reported in the previous paper. This is the second part of the study. For the study, recent trend of traditional cutting system was analyzed. Also, cost of the prototype cut-feeder was analyzed and determine the break-even point of farm size was determined by comparing with traditional method using a traditional cutter. A prototype cut-feeder was investigated with the fact that working performance, fiber length and shape of roughage and feeding quality was good. Operating cost of the prototype cut-feeder decreased rapidly with an increase of farm size. Break-even point in terms of farm size was 36 heads for beef and 28 heads for dairy. Also, costs estimated were 118,000 won/head year and 148,000 won/head year, respectively.

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1114-1121
• /
• 2000

A flexible disk grinding process model was developed based on the dynamic relationship proposed by Kurfess and the influence of the major system parameters which potentially affect the grinding process was studied. Due to the process complexities, several new parameters were assumed to be kinematically dependent on the geometric layouts of the process. Different process stages had been defined depending on the kinematic relationships between the grinding disk and workpiece. A trend of depth of cut was simulated using the proposed model and compared with the empirically measured data in two dimensions. Due to a poor prediction capability of the first model, a modified model was proposed and a better performance has been proved to reveal a closer description of processed surface quality. Also a deflection length has been verified using a different analytical approach.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.792-801
• /
• 1996

A thinning algorithm -based image analysis technique was developed to measure corn root lengths. The root length measurement method was evaluated by comparing thread lengths measured by the image analysis system with actual thread lengths. The length measurement method accurately estimated actual thread lengths (less than 2% calculated error). Also, a rapid root length density measurement procedure, which utilizes the above root length measurement method, was developed to estimate corn root length density without washing the roots. Root length densities estimated from the cut soil surface of core samples taken from the field were paired with the root length densities determined from washed roots from the same soil core sample. A linear relationship between these two values was expected and was found. Eliminating the root washing procedure reduces the time required for measuring corn root length density substantially.

• Journal of Korean Society of Forest Science
• /
• v.101 no.3
• /
• pp.344-355
• /
• 2012

This study was conducted to analyze on the operational time and productivities of logging operations in whole-tree logging operation system by tower-yarder and swing-yarder, and in cut-to-length logging operation system by excavator with grapple in order to establish the efficient logging operation system and to spread logging operation technique. In the analysis of operational time, in case of whole-tree logging operation system, the felling time was 46.6 sec/cycle by chain saw, the yarding time was 480.6 sec/cycle by tower-yarder, the yarding time was 287.4 sec/cycle by swing-yarder and the bucking time was 155.14 sec/cycle by chain saw. In case of the cut-to-length logging operation system, the felling and bucking time was 225.65 sec/cycle by chain saw, the cut-to-length extraction time was 4,972 sec/cycle by excavator with grapple, the branches and leaves extraction time was 3,143 sec/cycle by excavator with grapple. The forwarding time was 4,688 sec/cycle by wheel type mini-forwarder, the forwarding time was 2,118 sec/cycle by excavator with grapple and small forwarding vehicle. In the analysis of operational productivities, in case of whole-tree logging operation system, the average felling performance was $57.89m^3/day$ by chain saw, the average yarding performance was $20.3m^3/day$ by tower-yarder, $31.55m^3/day$ by swing-yarder respectively, the average bucking performance was $20.3m^3/day$ by chain saw. In case of the cut-to-length logging operation system, the average felling and bucking performance was $11.96m^3/day$ by chain saw, the average cut-to-length extraction performance was $34.75m^3/day$ by excavator with grapple, the average branches and leaves extraction performance was $37.66m^3/day$ by excavator with grapple, the average length of operation road construction was 73.8 m/day by excavator with grapple. The average forwarding performance by wheel type mini-forwarder and the average forwarding performance by excavator with grapple and small forwarding vehicle was $15.73m^3/day$ and $65.03m^3/day$, respectively.

• Journal of Biosystems Engineering
• /
• v.24 no.1
• /
• pp.67-74
• /
• 1999

A prototype cut-flower sorter was developed and tested for its performance with five varieties of roses. Support plates driven by a chain mechanism transported the roses into an image inspection chamber. Color image processing algorithms were developed to evaluate the length, thickness, and straightness of stem and color, height, and maturity of bud. The average absolute errors of the system for the measurements of stem length, stem thickness, and height of bud were 19.7 mm, 0.5 mm, and 3.8 mm, respectively. The results of classification by the sorter were compared with those of a human inspector for straightness of stem and maturity of bud. The classification error for the straightness of stem was 8.6%, when both direct image and reflected image by a mirror were analyzed. The accuracy in classifying the maturity of bud varied among the varieties, the smallest for‘Nobless’(1.5%) and the largest for‘Rote Rose’(13.5%). The time required to process a rose averaged 2.06 seconds, equivalent to the capacity of 1,600 roses per hour.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 2001.04b
• /
• pp.51-56
• /
• 2001

This study was carried out to research the effect of nutrient composition and GA4＋7 on growth, flower quality and bulb development in special hydroponics of cut tulip. Flowering of 'Cassini' was markedly accelerated by standard+GA4＋7, K200＋GA4＋7, N250＋GA4＋7 treatment, last internode was increased by N250 as compared with other treatment. For 'Christmas Marvel', flowering was promoted by K250＋GA4＋7, last infernode and total length were also increased with K250＋GA4＋7 as compared to other treatment. For 'Golden Apeldoorn', flowering was accelerated by K200＋GA4＋7, last internode was increased with N300＋GA4＋7 treatment and total length was increased in N250＋GA4＋7 treatment as compared with the standard plants. Bulb weight and number of 'Cassini', 'Christmas Marvel'and 'Golden Apeldoorn' were decreased by GA4＋7 as compared to non-treatment, and bulb diameter was not affected by GA4＋7.

• Journal of Veterinary Clinics
• /
• v.37 no.4
• /
• pp.180-184
• /
• 2020

The purpose of this study was to report the reliability and validity of oblique single-cut rotation osteotomy (OSCRO) in 3D-reconstructed canine bone models with femoral varus and torsional deformities. A healthy adult male beagle was recruited to create a 3D bone model, and this bone model was modified by using a 3D program. Fifteen bone models were constructed for this study. OSCRO simulation was performed in accordance with the plan after printing using a 3D printing machine. The anatomical lateral distal femoral angle (aLDFA), anteversion angle (AA), anatomical caudo-distal femoral angle (aCdDFA), mechanical caudo-distal femoral angle (mCdDFA) and pre- and postoperative bone length were calculated. There were no significant differences between the target values and postoperative values. In addition, the difference between pre- and postoperative bone length was small (p = 0.001). Our findings suggest that OSCRO could be an effective surgical option for MPL with bone deformities in small-breed dogs that often undergo conventional distal femoral osteotomy.

• Journal of Korean Society of Forest Science
• /
• v.86 no.4
• /
• pp.476-488
• /
• 1997

The purpose of this study was to figure out the suitable field standards for revegetation measures on cut-slopes in consideration of the environmental factors. The field survey was conducted from 1995 to 1996 on highway cut-slopes. The results obtained could be summarized as follows; The major revegetation measures surveyed were 5 major measures as a whole in descending order of seed-spraying measures, block-sod pitching measures, latticed block pitching measures, hydro-seeding measures with seed-fertilizer-soil materials, and several netting measures on highway cut-slopes. According to the analysis of the environmental factors, the plant coverage was affected several major environmental factors which were soil factors(soil hardness, soil texture, soil and rock condition), and site factors(slope gradient, slope length). From a viewpoint of optimum selection, the major 3 factors(soil factors, slope gradient factors, slope length factors) should be considered for selection of revegetation measures on highway cut-slopes.