• Horticultural Science & Technology
• /
• v.30 no.1
• /
• pp.13-20
• /
• 2012

This study was carried out to examine the effect of cutting condition on the growth of rooted cuttings and their subsequent growth of cut flower in plug cutting of Dendranthema grandiflorum 'Baekma'. The more leaves were attached to the cutting, the higher shoot growth of rooted cutting was observed. Cutting with two to six leaves was effective in shoot growth and rooting than any other treatment. Shoot growth of rooted cutting was not affected by cutting length, but rooting was better in 5 to 7 cm long cutting. Shoot growth and rooting of rooted cutting was promoted by increasing the cutting diameter, and rooting was better in 3.6-4.2 mm thick cutting than 3.1 mm thick cutting. As the treating concentration of NAA increased, shoot growth was inhibited and root length shortened in rooted cutting. Soaking with $100mg{\cdot}L^{-1}$ ${\alpha}$-naphtalene acetic acid (NAA) for 1 h was effective in shoot growth and rooting. Root growth such as root number, root length, and root weight was better in rooting medium mixed with 2:2 of peatmoss:perlite than the other treatments. When rooted cutting produced from cutting with four or six leaves was planted, better length, weight, and leaf number of cut flower was observed. In rooted cutting produced with 7-9 cm long cutting, growth of cut flower such as length, weight, and ray flower number was more effective than the others. Therefore, it is recommended that the 7 cm long and 3.6 mm thick cutting with four to six leaves is used to improve their rooting and subsequent growth of cut flower in plug cutting of Dendranthema grandiflorum 'Baekma'.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.4
• /
• pp.419-425
• /
• 2009

Recently, the number of shallow tunnel construction increases to improve the structural safety and environment-friendliness. In Semi-Cut and Cover Method, ground is excavated to the crown arch level and braced rib arch is set to backfill before the excavation of lower face. Semi-Cut and Cover Method is proposed to solve the problems occurred by the conventional Cut and Cover Method, such as unstability, high-cost and the large cutting slope to be reinforced. In this paper, the behaviors of Braced Rib Arch in shallow tunnel excavated by semi-cut and cover method was studied. Model tests in 1:10 Scale were performed in real construction sequences. The distance between supports of rib arch was 1.8 m and the length of spacer was 1.0 m. the size of test pit was 4.0 m (width)$\times$3.3 m (length) 4.0 m (height) in dimension. Tests results show that backfill load acting on arch was smaller than that in the conventional Open-Cut Method.

• Transactions of Materials Processing
• /
• v.15 no.4 s.85
• /
• pp.311-318
• /
• 2006

One of the most important quality problems in flat plate leveled from hot rolled coils in cut-to-Iength lines is bowing and cambering when they are cut in small width parts. It is verified analytically and experimentally that residual stress remained in plate is th ε source of the problem. In order to produce low residual stress flat plate from hot rolled coils, the proper conditions of leveling are studied and two things are implemented. One is proper plastic deformation area ratio to reduce residual stress within customer requirement by applying suitable plastic deformation and maintain leveling load within structural strength limit of leveler. The other is maintaining uniform plastic deformation along the width of the plate during leveling. Customer requirement for residual stress is met by applying above 70% of plastic deformation area ratio and uniform deformation along width of coil by adjusting back up rolls according to deformation analysis of work roll and back up roll assembly and leveling tests.

• International Journal of CAD/CAM
• /
• v.6 no.1
• /
• pp.167-172
• /
• 2006

Recently, wire-EDM became a necessity for many engineering applications, particularly in the dies making. No-Core cut process is helpful for operations in which falling slug can jam the machine or wire. In this paper a proposed CAM system (called NCPP) is introduced, to overcome the limitations of the existing CAM systems in the machining of No-Core cut. The proposed CAM system (NCPP) provides pocketing of No-core cut and optimal selection of the position of starting hole (wire threading point), to minimize toolpath length. It was written for data exchange between CAD-CAM-CNC machines. This data model will become part of the ISO (Data model for Computerized Numerical Controllers) international standard. The NCPP system has been implemented in Visual C++. Many examples are used to illustrate NCPP system. The results show that, NCPP saves the machining time by significant value. This value depends on the shape and complexity of the workpiece that is being cut.

• Journal of Forest and Environmental Science
• /
• v.30 no.1
• /
• pp.71-75
• /
• 2014

Forest roads failure is one of the most common problems caused by heavy rainfalls. This study investigated the characteristics on stabilization measures installed for cutting slopes failure of forest road resulted from heavy rainfalls. Three primary factors (slope length, slope gradient, soil type) affecting cutting slope failure were considered and stabilization measures were classified into two types (A type: wooden fence, vegetation sandbag, stone masonry; B type: wire cylinder, gabion, concrete retaining wall) through discriminant analysis based on their capacity of resistance to slope failure. Results showed that A type was mainly installed in such conditions as cut slope <8 m, cut slope gradient $30-40^{\circ}$ and soil type with soil while B type occurred in locational conditions as cut slope length >8 m, cut slope gradient < $30^{\circ}$ and > $30^{\circ}$, and soil type of gravelly soil and rock.

• Geomechanics and Engineering
• /
• v.38 no.4
• /
• pp.421-437
• /
• 2024

The soil nailing method entails the utilisation of nails to reinforce and stabilise a zone of soil mass. This is widely used for various applications due to its effective performance under various loading conditions. The seismic response of 6m high vertical soil-nailed cut in various site classes under dynamic excitations has been investigated in this study considering various lengths and inclinations of nails. The influence of frequency content of dynamic excitation on the response of structure has been assessed through finite element analysis using time history data of three different earthquakes. The seismic stability of the nailed cut in retaining soil in various sites under El Centro, Kobe and Trinidad earthquake ground motion is evaluated based on maximum acceleration response, maximum horizontal deformation, earth pressure distribution on the wall and maximum axial force mobilised in nails. The optimum nail inclination is identified as 15° and a minimum nail length ratio of 0.7 is essential for a stable vertical cut under dynamic excitations.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.722-726
• /
• 2010

Inventory survey is process collecting data about cut slope. It's different from inspection. It contains not only basic information about cut slope, especially location, GPS positioning, height, length, weathering, joint direction, water conditions but also level of danger and damage. Collected data are being used get at status about cut slope along national roads. And It helps judging about priority of detailed investigation. According to results of analysis, we found better method about maintenance of cut slope. Later on, if inventory research is finished, we will understand characteristics of collapse slopes.

• Journal of Korean Society of Forest Science
• /
• v.102 no.2
• /
• pp.229-238
• /
• 2013

This study was conducted to analyze on the operational cost of logging operations in the whole-tree logging operation system by tower-yarder and swing-yarder, and in the cut-to-length logging operation system by excavator with grapple in order to spread efficient logging operation technique and to establish the logging operation system. In the results of the analysis of operation cost, in case of the whole-tree logging operation system, the operation cost was 2,099 won/$m^3$ in felling by chain saw, 28,286 won/$m^3$ in yarding by tower-yarder, 18,265 won/$m^3$ in yarding by swing-yarder, 18,939 won/$m^3$ in bucking by excavator with grapple and chain saw, 20,484 won/$m^3$ in forwarding and accumulation by wheel type mini-forwarder, 12,701 won/$m^3$ in forwarding and accumulation by excavator with grapple and small forwarding vehicle. In case of the cut-to-length logging operation system, the operation cost was 10,160 won/$m^3$ in felling and bucking by chain saw, 7,567 won/$m^3$ in cut-to-length extraction by excavator with grapple, 6,982 won/$m^3$ in branches and leaves extraction by excavator with grapple, 3,040 won/$m^3$ in the operation road construction by excavator with grapple, 20,484 won/$m^3$ in forwarding and accumulation by wheel type mini-forwarder, 12,701 won/$m^3$ in forwarding and accumulation by excavator with grapple and small forwarding vehicle.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.170-177
• /
• 2000

Sorting cut roses according to quality is very essential to increase the value of the product. Many factors are involved in determining the grade of cut roses: length, thickness, and straightness of stem, color and maturity of bud, and extra. Among these factors, the stem straightness and bud maturity are considered to be difficult to set proper classification criteria. In this study, a prototype machine and an analysis procedure were developed to grade cut roses according to stem straightness and bud maturity by utilizing color image processing and neural network. The test results indicated 15.8% classification error for stem straightness and 10.0% for bud maturity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.200-200
• /
• 2011

Although the cut-off probe, a precise measurement method for the electron density, is widely used in the industry, the physics on the wave spectrum of the cut-off is not understood yet, only cut-off point frequency containing the information of electron density has been analyzed well. This paper analyzes the microwave frequency spectrum of the cut-off probe to see the physics behind using both microwave field simulation (CST Microwave Studio) and simplified circuit simulation. The result shows that the circuit model well reproduces the cut-off wave spectrum especially in the low frequency regime where the wavelength of the driving frequency is larger than the characteristic length and reveals the physics of transmission characteristics with frequency as resonances between vacuum, plasma and sheath. Furthermore, by controlling the time domain in solver of the microwave simulator, the cut-off like transmission peaks above the cut-off frequency which has been believed as cavity effect is verified as chamber geometry effect. The result of this paper can be used as the basis for the improvement of cut-off probe.