• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.1
• /
• pp.62-66
• /
• 2010

A new soft recovery pulse width modulation quasi resonant converter composed only passive devices snubber network is proposed. This passive devices snubber network is revised form of folding snubber network that suppressed the reverse recovery current of main rectify diode in PWM converter. It also makes the MOSFET switching devices operate in soft state. The efficient of the proposed converter is almost same level to that of the converter of active snubber type. The overall circuit is simple and easy to realized. Therefore, it is suitable to apply to middle range output power source.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.3
• /
• pp.254-262
• /
• 1990

In the active power filter, the PWM method for controlling the power converter plays an important role for the performance and the efficiency of the filter. In this paper, a new PWM method for the single phase current source type active power filter is presented, which is intended particularly for obtaining the maximum efficiency of the compensation. This method is basically based upon the optimized injection method, but in contrast to the existing method, this method adapts the optimized injection method by putting not only the pulse width, but also the pulse position into control variables. By doing this, when the number of pulses per one cycle is N, lower order harmonics up to the Nth order can be completely eliminated by the filter. So, this method is much more efficient than any other existing method. These characteristics are well verified by the computer simulations and the experiments.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.4
• /
• pp.174-180
• /
• 2005

Linear pulse motor (LPM) has the vibration during the operation because of magnetic characteristic which is caused by the mechanical configuration and the electromagnetic property. This paper proposes the calculation of thrust on the base of magnetic equivalent circuit for the purpose of the vibration minimization of LPM. The permeance of LPM is calculated and simulated from the construction tooth. The thrust is compared with the analytical method, the 3D finite element method (FEM) and the experimental values. The vibration of LPM is measured and estimated to select the input current wave for an optimal operation condition.

• Journal of Power Electronics
• /
• v.9 no.1
• /
• pp.18-25
• /
• 2009

Conventional series-resonant pulse frequency modulation controlled DC-DC high power converters with a high-frequency transformer link which is designed for driving the high power microwave generator has the problem of hard switching commutation at turn-on and turn-off of active power switching devices. This problem is due to the influence of the magnetizing current of the high-frequency transformer. This paper presents a novel prototype for a high-frequency transformer using parasitic parameters with a lossless inductive snubber and a series resonant capacitor assisted series-resonant zero current switching pulse frequency modulated DC-DC power converter, which is designed using a high power magnetron for microwave ovens. In order to implement a complete and efficient soft switching commutation, the performance of the new converter topology is practically confirmed and evaluated in the prototype of a power microwave generator.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.400-402
• /
• 2007

This paper presents a vector control implementation for PMSM using Real Time Workshop and Embedded Target for TI C2000 DSP in MATLAB/SIMULINK. Speed, current and vector controllers are easily designed and implemented by using the MATLAB/SIMULINK program. Feedback of motor speed is processed through C28x QEP(Quadrature Encoder Pulse) block from encoder pulse. 3-Phase currents ares processed through C28x ADC block from current sensors. And gating signal of PWM inverter is generated through SVPWM and PWM block. Real-time program is drawn using SIMULINK and then converted program code for speed control of PMSM is downloaded into the TI eZdsp 2812 board. Experiments were carried out to examine validity of the proposed vector control implementation.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.81-82
• /
• 2006

This paper presents the influence of the compositions of sintered Ti-Ni alloys on their thermo-mechanical properties. The Ti-Ni alloys having various compositions from 50at%Ni to 51at%Ni were sintered using elemental Ti and Ni powders by a pulse-current pressure sintering equipment. The deformation resistance in stress-strain curves increased with an increase in Ni content. In the case of Ti-50at%Ni, tensile strength and elongation were more than 500 MPa and 7%, respectively. The increase in Ni content also makes the transformation temperatures lower. The deformation resistance at a test temperature change from 293K and 353K in isothermal tensile test increased with elevating test temperature.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.5
• /
• pp.421-426
• /
• 2017

Herein, we investigated surface morphological characteristics of anodic films on Al6061 alloy prepared by unipolar pulsed Micro-arc oxidation (MAO) in a mixed solution of $Na_2SiO_3$ + KOH. The number and size of pores as well as craters on anodic alumina surface were studied as a function of different voltages, duty cycles and applied anodic current densities. The morphological characteristics of all samples were investigated by scanning electron microscopy, conforming that the most uniform surface morphology of MAO films on Al1050 alloy was obtained at high applied current density with low duty cycle.

• Journal of the Korean institute of surface engineering
• /
• v.22 no.4
• /
• pp.207-214
• /
• 1989

The surface morphology and the proferred orientation of the Pb-Sn alloy electrodeposite were investated by the change of electrolysis conditions in pulse current electroplating. The preferred orientation of Pb-phase in alloy deposits was changed in the sequence of (110)longrightarrow(100)or(100)+(111)longrightarrow(111) with increasing peak current density, while that of $\beta$-Sn phase changed from (321)+(301)to(301)+(111) mixed orientation. The surface morphology was closely related to the preferred orientation of alloy electrodeposits. The alloy deposits, which had (100)or(111) for pb-phase and (321)or(100)(301)for $\beta$-Sn sespectively, showed the surface structure of granular crystallites. The alloy deposits whih mixed orientations for both phases had microstructure of closely the closely stacked crysrallites, which was inclined to the surface.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.840-843
• /
• 1993

In this paper, an LPM controller using microprocessor was implemented and adopted Microstep method to control the LPW. In Microstep method, current waveform is sinusoidal not square. This method is characterized by less vibrating, less noisy, and more precise position control. Also, we simulate the static thrust characteristics for each waveform. The experiment was performed according to the mechanical vibration at the acceleration mode and slewing mode. The current tracks reference sinusoidal waveform well and stability was improved as we expected. Therefore, the possibility of the open loop position control was proposed.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.137-139
• /
• 2001

This paper describes a new methods of detecting rotor position in SRM(switched reluctance motor). The Conventional method of position sensorless control for SRM is measuring phase current and pulse voltage applied in unexcited phase. The estimation of rotor position based on the detection of inductance by pulse current. Implementation is via low-cost electronic circuits with DSP320F241. Test results show that this technique is a possible approach to detect the rotor position of an SRM.