• International Journal of Highway Engineering
• /
• v.19 no.3
• /
• pp.11-18
• /
• 2017

PURPOSES : This study investigates the effect on concrete pavement accordance with the curing methods in cool weather and supports the best method in the field. METHODS : Two field tests evaluated the curing methods of concrete pavement in cool weather. Firstly, five curing methods were tested, including normal curing compound, black curing compound, bubble sheet, curing mat, and curing mat covered with vinyl. Concrete maturity was compared from temperature data. Secondly, normal curing compound and curing mat with vinyl, which showed the best performance, were compared in terms of maturity and join condition index. RESULTS:From the field tests, it is an evident that curing mat with vinyl accelerated the concrete strength. Therefore, it is possible to conduct saw-cut works in cool weather, which minimizes damage on concrete at joint. CONCLUSIONS : For concrete pavement in cool weather, using curing mat with vinyl as the curing method could overcome the strength delay. Therefore, strength and durability problems on concrete at joint due to cool weather would be fewer in the future.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.3
• /
• pp.211-217
• /
• 2016

In this research, the performance of surface covering technique using a white-colored bubble sheet on reducing the cracking due to the plastic, and drying shrinkages for high rise building construction were evaluated by comparing the exposed surface without any surface treatment. From the results of the experiment conducted during fall season, desired results of decreased numbers, length, maximum width, and area of cracking were obtained without a significant difference on heat of hydration and cumulative temperature. Therefore, it is considered that the surface covering technique using bubble sheet is an appropriate method for preventing plastic and drying shrinkage cracking at fall season concrete construction.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.413-419
• /
• 2009

As the refractive index of the prism layer becomes higher, the optical performance of the prism sheet gets better and the efficiency of the LCD backlight unit is improved. In order to increase the refractive index of the prism layer, the ultraviolet curing type resins were prepared by mixing high refractive index materials containing aromatic groups and the multi-functional reactive diluents. By using 9,9-bis [4-(2-acryloyloxyethoxy)phenyl] fluorene, the refractive index of the prism layer was increased up to 1.58 and the brightness of the backlight unit was improved. Since the light source used in the backlight unit caused the yellowing in the prism sheet and deteriorated the brightness accordingly, the hindered amine light stabilizer was used to improve the yellowing resistance successfully.

• Design & Manufacturing
• /
• v.16 no.1
• /
• pp.43-49
• /
• 2022

As technologies in various industrial fields develop, high-quality parts are required. In the past, precision parts were produced by the contact machining method, but the contact machining method has clear limitations. In order to solve this problem, research on a non-contact processing method has been conducted, and laser processing and electric discharge processing are representative. However, the non-contact method has a problem in that productivity is insufficient, and there is a problem that it takes a lot of time to continuously process microholes. Researchers have developed an electron beam drilling equipment for continuous processing of fine holes, and a vaporization amplification sheet to increase the processing efficiency of the equipment. In this study, a cylindrical vaporization amplification sheet using room temperature curing type silicon was fabricated, and the metal distribution and thickness uniformity of the produced sheet were analyzed. In order to manufacture a cylindrical vaporization amplification sheet, an equipment capable of using centrifugal force was developed, and a sample in which metal powder was evenly distributed and a constant thickness was produced.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.160-161
• /
• 2022

This study is to investigate the temperature history over time of the cement mortar to confirm the bubble sheet insulation effect using the heat generat sheet. As a result of the experiment, it was confirmed that the heating effect was 6℃ higher on average than other types of sheets when the heating sheet is attached on the bottom of the double layered bubble sheet. For future research, it is planned to verify the heating performance by using the heating sheet under the same environmental conditions as the heating performance will be verified.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.03a
• /
• pp.241-246
• /
• 1998

• Textile Coloration and Finishing
• /
• v.34 no.3
• /
• pp.157-164
• /
• 2022

This study tried to analyze the heat resistance properties by blending epoxy and phenolic resin in a certain ratio, and to analyze the adhesive properties at the time of metal-polymer hetero-adhesion by applying Epoxy-phenolic resin between a silicon steel sheet and m-aramid sheet, the viscosity, adhesive peel strength, and adhesive cross section were measured using a rotational rheometer, a tensile tester(UTM), and a field emission scanning electron microscopy(FE-SEM). The thermal stability and heat resistance were confirmed by measuring the mass loss according to the temperature increase using Thermogravimetric analysis(TGA). After blending with epoxy and Phenolic resin(1:0.25 ratio) curing at 110℃ for 10 min, high adhesive strength was improved more than 40% compared to the adhesive strength using epoxy alone. When the space between the silicon steel sheet and m-aramid sheet, which is created during curing of the E-P blend, is cured with a slight weight, it is possible to control the empty space and improve adhesion.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.11a
• /
• pp.30-35
• /
• 2008

The purpose of EVA sheet in PV module is to bond or laminate the multiple layers of a module. We studied the influence of EVA sheet gel content on photovoltaic module durability. Gel Content was measured by manufacturing Glass/EVA Sheet/Back Sheet scheme at several curing temperature. Through this experiment, we could confirm that there are changes on Gel Content of EVA Sheet. The transmittance of $140^{\circ}C$/4min process condition was more excellent than the other condition at ultraviolet wavelength range. The thermal stability of $150^{\circ}C$/4min process condition was higher than the other condition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.365-366
• /
• 2009

Humidity curing of the concrete after placing is significant to ensure the crack resistance, strength, and durability. Generally, there are watering and sheet curing methods as humidity curing methods to the upper part of slab concrete, therefore this study investigates effects of these curing methods to preservation of humidity on the cement mortar.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.2
• /
• pp.224-230
• /
• 2012

In this paper, flame-resisting PMMA(polymethyl methacrylate) sheet was manufactured and its characteristics were tested. PMMA was synthesized by bulk polymerization of a monomer methyl methacrylate with addition of phosphorous flame retardant, triethyl phosphate and ethylene glycol dimethacrylate as a cross linking agent. PMMA sheet was manufactured by using the cell molding method, which does not alter or affect the existing property of PMMA. Then the characteristics of PMMA sheet were tested for the TEP content, the content and curing time of EGDMA. As TEP content increases, the length of carbonization lessens and the amount of char production increases. As a result, it strengthened the effect of flame retardants. But the hardness of the sheet decreased as TEP content increased. However, hardness increased when EGDMA was added up to 3 wt% while curing time was decreased from 3 hours to 2 hours. There was no change of hardness when more than 3 wt% of EGDMA was used.